A cable is placed around three parallel pipes. Two of the pipes are fixed and do not rotate, the third pipe is slowly rotated.The coefficients of friction areH₂-0.25 andH=0.20. Given, M = 40 lb.W1AWсBDetermine the largest weight Wthat can be raised if only pipe A is rotated counterclockwise.The largest weight that can be raised if only pipe A is rotated counterclockwise is[lb.

Given,Coefficients of friction,

A cable is placed around three parallel pipes. Two of the pipes are fixed and do not rotate, the third pipe is slowly rotated. The coefficients of friction are H₂- 0.25 and H= 0.20. Given, M = 40 lb. W1 W Determine the largest weight Wthat can be raised if only pipe A is rotated counterclockwise. The largest weight that can be raised if only pipe A is rotated counterclockwise is lb.

A cable is placed around three parallel pipes. Two of the pipes are fixed and do not rotate, the third pipe is slowly rotated. The coefficients of friction are H₂- 0.25 and H= 0.20. Given, M = 40 lb. W1 W Determine the largest weight Wthat can be raised if only pipe A is rotated counterclockwise. The largest weight that can be raised if only pipe A is rotated counterclockwise is lb.

International Edition---engineering Mechanics: Statics, 4th Edition

4th Edition

ISBN:9781305501607

Author:Andrew Pytel And Jaan Kiusalaas

Publisher:Andrew Pytel And Jaan Kiusalaas

Chapter7: Dry Friction

Section: Chapter Questions

Problem 7.85RP

See similar textbooks

Similar questions

Two identical chairs, each weighing 14 lb, are stacked as shown. The center of gravity of each chair is denoted by G. The coefficient of static friction is 0.2 at B (the contact point between the chairs) and 0.35 at A, C, and D. Determine the smallest force P that would cause sliding.
A wedge is used to prop up the 6000-lb block of marble. The wedge angle is =30, and the angle of static friction is s=12 between all contact surfaces. Determine the smallest force P that would prevent the wedge from sliding out.
Draw the FBD of the entire frame, assuming that friction and the weights of the members are negligible. How many unknowns appear on this FBD?
The leather rein used to fasten the horse to the hitching rail weighs 3.5 oz per foot. The coefficient of static friction between the rail and the rein is 0.6. If a 34-lb force acting on the bridle is sufficient to restrain the horse, determine the smallest safe length L for the free end of the rein.
The coeffient of static friction between the uniform bar AB of weight W and the ground is 0.45. Find the smallest angle and the corresponding force P that would initiate simultaneous tipping and sliding of the bar.
The brake pads at C and D are pressed against the cylinder by the spring BF. The coefficient of static friction between each pad and the cylinder is 0.15. Find the smallest tension in the spring that would prevent the cylinder from rotating when the clockwise couple M=2200lbin. is applied. Neglect the weights of the members.
The figure shows a steel bar being processed by a rolling mill. Given that P=80kN and r =0.016, determine the force F required to advance the bar at a constant speed.
Find the tension T in the cable when the 180-N force is applied to the pedal at E. Neglect friction and the weights of the parts.
The 600-lb cable spool is placed on a frictionless spindle that has been driven into the ground. If the force required to start the spool rotating is F = 160 lb, determine the coefficient of friction between the ground and the spool. Neglect the diameter of the spindle compared to the diameter of the spool.
The normal pressure acting on the disk of the sander is given by p=(4/3)+(r2/6), where p is the pressure in pounds per square inch (psi) and r represents the radial distance in inches. Determine the torque C required to operate the sander at constant speed if the kinetic coefficient of friction for the surface being sanded is 0.86.
Calculate the horizontal force P required to push the 85-lb lawn mower at constant speed. The center of gravity of the mower is at G, and the coefficients of rolling resistance are 0.12 for the front wheels and 0.18 for the rear wheels.
The woman is trying to move the crate of weight W by pulling on the rope at the angle to the horizontal. Find the smallest possible tension that would cause the crate to slide and the corresponding angle .