A cable with supports at the same elevation has a span of 600 ft and a sag of 60 ft. The cable supports a uni- formly distributed load of 750 lb/ft along the horizontal. Determine The length of the cable.
Q: The wide-flange member is made from an elastic perfectly plastic material. Determine the shape…
A: The shape factor of the material is the ratio of the plastic moment to the yield moment. The plastic…
Q: Determine the shape factor for the member having the tubular cross section.
A:
Q: 2. The half section of an arc is under a uniformly varying load. If the weight of the arch is 50,000…
A: The centroid of a body is the point where all sides have equal volume. The centre of mass of a solid…
Q: Which of the following is the shear force diagram for the beam below. 12 kN/ m C 3 m 6 m
A: Let the support reaction at B and C are RB & RC. The reactions are calculated as :…
Q: 03 m k= 200 N /m 04m
A: according to the given details in the question.
Q: The horizontal beam is assumed to be rigid while supporting the distributed load. Determine the…
A: Please find the answer below
Q: PROBLEM 1.6 1.7 A level scaffold is to be supported at the center of a 12-ft ladder, as shown.…
A: TO FIND Required length x . and, angle ∅. CONCEPT USED Pythagorus theorum Triangle symmetry rule
Q: Determine the magnitude of the vertical deflection of
A: Given data; Flexural rigidity,EI=200 N.m2Applied moment,Ma=1 mLength,l=2 mDetermine the magnitude of…
Q: Two PARALLEL springs A and B has spring constants 269 N/mm and 91 N/mm, respectively. If the…
A: here, equivalent stiffness in parallel connection Keq. = 269 + 91 = 360 N/mm here, F = Keq. ×…
Q: A locomotive semi-elliptical laminated spring has an overall length of 1.5 sustains a load of 85 KN…
A:
Q: Determine the reactions at the beam supports for the given loading.
A: Determine the lengths upto which Uniform Varying Load is acting by using similar triangles and…
Q: L=20 m Bmax h= 6 m
A:
Q: Determine the shape factor for the wide-lange beam.
A: The shape factor is dimensionless and depends upon the shape and is used to enhance the efficiency…
Q: Determine the value of Elv (in Ib ft³ ) at the section below the load P for the beam loaded by two…
A:
Q: 600 N 800 N 1m 2 m 900 N. m 600 N 800 N Im 2 m 900 N. m 600 N 800 N 1m 1m 2m
A: Explaining the correct free-body diagram (FBD) of the beam.
Q: Two men are carrying on their shoulders a 500-N load suspended from a piece of bamboo 3 m long with…
A:
Q: Given the load the diagram of the overhanging beam 900 lb 400 lb 60 lb/ft A C. 4 ft RA 8 ft 6 ft Rc…
A:
Q: Determine the crippling load for a T-section of dimensions 12 cm x 12 cm x 2 cm and 5 m long which…
A: Given data as per the question Dimensions of T section =12 cm×12cm×2cm Lenth =5 m Young modulus…
Q: 1- Determine the total deformation of the suspended homogenous cone of height "h", density "p", and…
A: Given - Length of conical bar =h Radius of conical bar =r =d/2 Determine the elongation due to self…
Q: Q3\ A beam AB, 6 m long, is simply supported at A and D (where D is 1.5 m from B). It carries a 24…
A: Sign Convention SFD 1) Right Upwards Negative 2) Right Downward Positive 3) Left Upwards Positive 4)…
Q: Determine the maximum height h from which an 80-lb weight can be dropped onto the end of the A-36…
A: Write the expression for Static deflection due to point load acting at the end.
Q: AT-Shaped beam has a length of L-3.5 m is acted upon by the distributed load as shown which has a…
A: Representing system of forces into single force is called resultant force
Q: A flexible cable with supports at the same elevation has a span of 400 ft. If the length of the…
A: Given Data: The length of the cable is L = 500 ft. The distance between the supports of the cable…
Q: Determine the value of Elv (in Ib ft³ ) at the section below the load P for the beam loaded by two…
A: Let the pin end be "A", point at which load P acting is "B", point at which load Q acting is "C"",…
Q: 7- Determine the load in each road (the rod from same material and same area ) 2 m 2 m 1.5 m A 1.5 m…
A: To find load in each rod
Q: For the given shear diagram, draw the actual load (indicate the position of the supports) and its…
A: We know that the shear force diagram is 1 degree higher than the actual loading diagram and the…
Q: the simply supported beam carries a uniformly distributed load of intensity 600 N/m. If E = 10 GPa,…
A:
Q: 13.12 A straight girder of uniform section and length L rests on supports at the ends, and is…
A: Given: Straight girder with uniform length=L Supports at ends To find: To prove it takes load…
Q: The magnitude of the vertical deflection of the free end is
A: Given data; Figure shown having following data;Length,l=1.0 m Flexural regidity EI=200 N.m2 Applied…
Q: determine the maximum load P that can
A: Given: Shear load resists by the nails 2.5 kN To determine : The maximum load that can be applied…
Q: w = 40 kip/ft w = 20 kip/ft a L = 30 ft
A: Dividing the load in two parts and then solve for the following
Q: Q2: Draw the S.F. and B.M. diagrams for the beam which is loaded as shown in Fig. Determine the…
A:
Q: Q14 Find the load .if the load distance 3m and effort distance 10m and effort=300N
A:
Q: Draw the free body diagram. 80 mg 60 20 650 mm 200 925 mm mm By
A: Solution: The free body diagram of the inclined beam is shown below:
Q: 10c The 9.75 m long beam is simply supported at A and B shown below with a uniformly distributed…
A:
Q: The rigid beam is supported by a pin at C and an A-36 steel guy wire AB. If the wire has a diameter…
A: Draw the schematic diagram for the triangle BB’C system. Determine the angle with the help of…
Q: Cantilever beam has fixed support at the point A as shown in Fig. 4. Determine the component of the…
A:
Q: The rigid beam is supported by a pin at C and an A-36 steel guy wire AB. If the wire has a diameter…
A: Consider the free body diagram shown below for the beam. The total weight on the beam is Length of…
Q: Determine the largest intensity w of the distributed load that the member can support.
A:
Q: Calculate the magnitude and the position from point ´a' of the resultant load caused by the loading…
A: Hello. Since you have posted multiple questions and not specified which question needs to be solved,…
Q: NO. 1. Determine the reaction forces in the following structures: 8 kips 15 kip . ft 5'- B F 5' D E…
A:
Q: The beam AB supports a load which varies an intensity of w1 = 6 N/m to w2 = 12 N/m.
A:
Q: Q1) The wall is 12-ft high and consists of 2 x 4 studs. On each side is acoustical fiberboard and…
A:
Q: The 2-inch-thick polymer block is bonded to the rigid support and to the steel plate, which is…
A: Stress is defined as the force per unit area and strain is the ratio of change in dimension to the…
Q: The precast floor beam is made from concrete having a specific weight of 23.6 kN/m³. If it is to be…
A:
Step by step
Solved in 3 steps with 4 images
- The cable supports three 400-lb loads as shown. If the maximum allowable tension in the cable is 900 lb, find the smallest possible sag hC at C.Cable AB supports the uniformly distributed load of 4 kN/m. If the slope of the cable at A is zero, compute (a) the maximum tensile force in the cable; and (b) the length of the cable.A cable with supports at the same elevation carries a uniformly distributed load of 500 Ib/ft along the hori- zontal. If the maximum tension in the cable is 100 kip and the sag at midspan is 40 ft, determine The horizontal distance between supports.
- A cable with supports at the same elevation has a span of 600 ft. The length of the cable is 630 ft. If the max- imum tension in the cable resulting from a uniformly dis- tributed load w along the horizontal is 360 kip, determine The sag in the cable at the middle of the span.is The left support of the cable shown in Fig. located 40 ft below the right support. The cable is horizontal at the left support. If the maximum tension in the cable re- sulting from a uniformly distributed load w along the hor- izontal is 400 kip, determine the length of cable 40 n 400 ftTwo men carry a load of 2 kN by means of two ropes fixed to the weight. One rope is inclined at 45º and the other at 30º to the vertical. Find the tension in each rope.
- A horizontal cable exerts a force of 399.971 pounds while holding a boom into place. Determine the angle the boom makes with the ground if it supports a 1000-pound load, as shown in the figure. Include fbd, given and solution.Find the support reaction at A and the tension at the rope from the beam shown bellow. The pulley is frictionless. Given: a = 8 ft, b = 4 ft, c = 2 ft, r = 6 in, w1 = 1500 lb/ft. Note: Draw the free body diagram and answers should be in 3 decimal places.Two men are carrying on their shoulders a 500-N load suspended from a piece of bamboo 3 m long with each man positioned at the ends. If the load is suspended 1 m from one end find the load carried by each.
- A cable with supports at the same elevation has a span of 550 ft. The cable weighs 4 lb / ft and the sag at midspan is 100 ft. Determine The tension in the cable at midspan.Q1/ The 500-kg uniform beam is subjected to the three external loads shown. Compute the reactions at the support point O. The x-y plane is vertical. 30° 15 kN.m 3 kN A C 1.4 kN 1.2 m 1.8 m 1.8 mA simple beam having a span of 6m has a weight of 20 kN/m. It carries a concentrated load of 20kN at the left end and 40 kN at 2m from the right end of the beam. If it is supported at 2m from the left end and at the right end, compute the reaction at the right end of the beam.