Q3- Only Answer two branches.a- calculate the atomic backing factor for Bc..b- 10 mm diameter of Brinall hardness ball when the load =500 kgr andHB= 300 determined the diameter of indenter.C- The diminutions of the low alloy steel impact test sample as shown infig below and the notched depth is 1.5 mm determine the impacttoughness if the impact energy absorption at test is 100 joul.Charpy10 mmso man

Because the volume of each of the eight corner atoms is shared between eight adjacent cells, each…

Answered: a- calculate the atomic backing factor…

Engineering

Mechanical Engineering

a- calculate the atomic backing factor for Bc..

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

1- The diminutions of the mild steel impact test sample as shown in fig below and the notched depth is 2mm determine the impact toughness if the impact energy absorption at test is 80 joul . Charpy 10 mm 55 mm 10 mm 2- Explain with the drawing the procedure of the charpy test. 3- Explain with the drawing the procedure of the Izod test. 4- Explain with the drawing the difference between Izod and charpy tes.
1- The diminutions of the mild steel impact test sample as shown in fig below and the notched depth is 2mm determine the impact toughness if the impact energy absorption at test is 80 joul. 2mm Charpy 10 mm 55 mm 10 mm
Calculate Brinell Hardness for Hardened AW-6060 Aluminium if mean depression diameters (d)= 5.64mm with applied load of * ?3000kgf
Using the tensile test simulation tool, a. generate the stress-strain curve for aluminum b. Indicate the following points in the stress-strain curve for aluminum and give the corresponding values: limit of proportionality elastic limit 0.2% offset yield stress (include the graph illustrating how this was determined) ultimate stress fracture stress c. Calculate modulus of elasticity. d. compare aluminum with nylon (include the related graph) and answer the following: Which has higher tensile strength? Provide the necessary values to support the answer. Which is stiffer? Support your answer with calculations.
In the state of loading as made of brittle material tensile and compression fracture values of the exposed arm, respectively. σUT=200 MPa and σUC=800 MPa and factor of safety n=4 as it is; a) First reduce the applied forces to point B, b) By determining the critical point of the critical section and stresses Calculate it and show it on the stress element. c) Calculate the diameter of the AB part according to the Coulomb criterion. Note: Neglect the effect of cutting forces.
During the test of hardness due to Brinell, the diameter of the testing sphere was0.01m, the exerted load was 3.0 tons and the diameter of the indented area wasapproximately 0.003 m. Find the value of the hardness for this material. Also find theTensile strength if the proportionality constant was approximately 3.45.
Problem 4: 6.43. The simple expressions for Rockwell hardness num- bers in Table 6.9 involve indentation, 1, expressed in millimeters. A given steel with a BHN of 235 is also measured by a Rockwell hardness tester. Using a 16 -in.-diameter steel sphere and a load of 100 kg, the indentation t is found to be 0.062 mm. What is the Rockwell hardness number? Solution:
Determine the strength of the bedrock granite. Assume you sampled the granite where it was exposed at the surface and ran a series of 4 triaxial compression tests (results given below). Determine the Coloumb coefficient (or friction angle) and the cohesion of the rock given these test results. Either use graph paper to draw Mohr’s circles and a failure envelope to help you determine these values or use the computer to make a plot. Show all your work for credit! Test Confining pressure Axial load at failure 1 4.5 MPa 35.5 MPa 2 9 MPa 50 MPa 3 17 MPa 73 MPa…
Q2/Calculate the impact resistance of a metal if it was chosen by the Charpy method, the cross-sectional area of the sample at the notch was 0.8 cm2, the pendulum weight of the hammer was 25.81 kg, the angle of elevation (a) was 141.5°, the length of the pendulum was 0.75 m, and the angle of turn back (ß) was 12°? E
A square cross-section v-notched specimen of height 75 mm has each side of 10 mm has been selected to perform Charpy impact test. A v-notch of thickness 1.9 mm is made at the middle of the specimen length. Determine the cross-sectional area at notch.
Calculate the elustic limit of the plate 10 plate 8X0 - S00 pounds of load material 6061 Aluminum - Determine whattypeof stress is acting at this point -calculate the magnitude of this stress
1. A bronze alloy specimen having a diameter of 12.8 mm and a gage length of 50 mm was tested to fracture. Stress and strain data obtained during the test are shown in Figure. Determine: 400 Upper scale a. the modulus of elasticity. b. the proportional limit. c. the ultimate strength. 320 Lower scale 240- d. the yield strength (0.20% offset). 160 e. the modulus of resilience. f. the true fracture stress if the 80 final diameter of the specimen at the location of the fracture was 10.5 mm. 0.100 0.200 0.300 0.400 0.005 0.010 0.015 0.020 g. The Poisson's ratio. Strain (mm/mm) Stress (MPa)