A centrifugal pump delivers 60 litres of water per second to a tank situated at a height of 20 metres.If the overall efficieney of the pump is 70%, find the power required for the pump. (Ans. 16-8 kW)1.

Answered: Image /qna-images/answer/6d6d119d-298e-4a7b-bc8f-4dc6ffa62987.jpg

Answered: A centrifugal pump delivers 60 litres…

A centrifugal pump delivers 60 litres of water per second to a tank situated at a height of 20 me If the overall efficiency of the pump is 70%, find the power reguired for the pump. (Ans, 16-8

International Edition---engineering Mechanics: Statics, 4th Edition

4th Edition

ISBN:9781305501607

Author:Andrew Pytel And Jaan Kiusalaas

Publisher:Andrew Pytel And Jaan Kiusalaas

Chapter8: Centroids And Distributed Loads

Section: Chapter Questions

Problem 8.113P: Calculate the resultant force caused by the water acting on the parabolic arch dam. The water levels...

See similar textbooks

Related questions

Q: Draw the schematic diagram of hydroelectric power plant. Label all the parts and write down the…

A: Electricity is harnessed from the water through the hydroelectric power stations. Various parts of…

Q: The component of Francis turbine which minimizes loss of kinetic energy at turbine outlet is a.…

A: Turbine: The mechanical device that always rotates and converts the energy that is taken from the…

Q: tion 20 When choosing the optimal pump, the operating point should be kept close to O maximum head…

A: The intersection of pump characteristic and piping system characteristic is called operating point…

Q: A two-lobe rotary positive-displacement pump, similar to that of Fig, moves 3.64 cm3 of tomato paste…

A: Given data

Q: Discuss with neat diagram the pump flow characteristics if pumps are used in : (i) Parallel (ii)…

A: When pumps are connected in parallel, the total discharge is equal to the sum of the flow from each…

Q: _ is an example for Non- Positive Displacement Pump.

A: A positive displacement pump is a pump in which a fixed amount of fluid is transferred in a cycle…

Q: trifugal pump lifts water from a sump to a m is suction lift. The suction and delivery on pipe is…

Q: A centrifugal pump delivers 25 liters of water per second against a head of 10 meters and running at…

Q: A single acting reciprocating pump having cylinder diameter of 150 mm and stroke 300 mm is used to…

A: Write the given values with the suitable variables. d=150 mm=0.150 mL=300 mm=0.3 mh=30 mN=60 rpm…

Q: 20. A centrifugal pump has an impeller 45 cms in diameter running at 450 rpm. The dischargė at inlet…

A: Given: Impeller diameter D2=45cm or 0.45m (Impeller diameter means diameter of the impeller at the…

Q: Figure shows two points a half-period apart in theoperation of a pump. What type of pump is this ?…

A: The working is as the centre rod moves to the right, the check valves allows A to fill and B to…

Q: 3.5 A pipe 50 cm in diameter carries water (10°C) at a rate of 0.5 m/s. A pump in the pipe is used…

A: Answer: The power that must be supplied to the pump is 203.7650 kW (273.1434 hp).

Q: Two centrifugal pumps, a 5-in delivering 129gpm and a 4.5 in delivering 140gpm are connected in…

A: Given data Two centrifugal pumps are present. Pump 1 delivers 129 gpm using 5 inch impeller Pump 2…

Q: B-A pump has the following parameters N=2133.5 RPM, Ns = 40 RPM, D= 37.1 cm and is used to pump…

Q: What power must be supplied by the pump to the system to move oil from the lower to the upper…

Q: The characteristics for a pump are given in the table below. The pump is required to left water…

Q: Discuss the primary difference between positive displacement pump and dynamic pump. Give example for…

Q: Q2) Centrifugal pump, works between two large and free surface tanks, of efficiency 80% driven by a…

Q: The performance data for a centrifugal water pumpare shown in Table P14-31 for water at 20°C…

A: Given that :- Volume flow rate (Lpm) =12 Firstly change into m^3 12 L/min = 12 × 10^-3 (m^3) /60…

Q: Pump charecterishics Curve halm), esyetem curve Q (mi/s) Q Pz # Show the location of operating point…

A: Location of operating point of the pump arrangement system-

Q: of positive displacement pump

Q: Explain the construction and working principle of a fixed vane pump with a neat diagram. Also derive…

A: VANE PUMP The drawback of gear pumps is minor leakage because of the space between gear teeth and…

Q: EX.1 An axial flow pump with an impeller rotor diameter of 30 cm handles water at a rate of 2.7…

A: Given, Diameter of first pump= D1=0.3m Diameter of the second pump= D2=0.2m Discharge…

Q: What is the performance of pump (in %, whole number) that supplies 80 gpm of water (80°F) with…

A: Solution is attached below:

Q: A horizontal axis wind turbine is installed at a location having free 3 m/s. The 75 m diameter rotor…

Q: siphon draws water fror nospheric pressure. Assur velocity at point P in the

A: introduction: we have to find out velocity at point P

Q: the ratio of power output of the pump to the power input to the pump is known as

A: Pump efficiency,η=Power output of pumpPower input to pump where,Power output=ρgQHwhere,ρ=density of…

Q: The 11-in Bell and Gossett pump is tobe scaled up to provide, at best efficiency, ahead of 250 ftand…

A: Given: The size of bell and Gosset pump, D = 11 in The head, h = 250 ft The flow rate, Q = 3000…

Q: 3. A centrifugal pump having an impeller of diameter 500 mm delivers 140 litres of water per second.…

Q: Q_3/Figure shows a pump employed for lifting water from a sump. If it is required to pump (60…

Q: Example (2-2): Find the specific speed of a double suction centrifugal pump delivering 1.5 m/s…

A: Data given- Q = 1.5 m3/s H = 15 m N = 725 rpm

Q: :-in the figure shown find the pump power if the discharge of oil is 200L/sec and the relative…

Q: Air 25 kPa Blade Water 3m 659 Jet W

A: As given that air pressure = 25 kPa, The height of water in the tank up to opening = 3 m, Weight of…

Q: A and B are homologous pumps operating at the speed of 800rpm.Pump A has an impeller with diameter…

Q: In the Figure.Q3, The energy decline of the connections and the pipe before the pump is 3m.…

Q: of the pump is 70%. Calculate (a) the developed head of the pump and (b) the total power input. (c)…

A: The water flow rate from reservoir is Q2=60 gal/min×0.003785 m3 1 gal×1 s60 min=3.75×10-3 m3/sec.…

Q: A centrifugal pump has r2 = 9 in, b2 = 2 in, and β2 = 35°and rotates at 1060 r/min. If it generates…

A: Given: Centrifugal pump rotates at N=1060 r/min, head generated is h=150 ft calculating the angular…

Q: Dove the inlet. There is no signifi local acceleration of gravity is 9.5 ess? Explain using…

Q: A pump has a displacement volume of 5 in3. rotates at 1000 rpm and 1000 psi. If the volumetric…

Q: Find the force required to hold the blade in position, if the jet weight (100kg) and discharge…

Q: A pump has overall efficiency of 70 %. It delivers 90 Ipm at 1000 rpm and 700 N/cm". If the prime…

A: Given: overall efficiency of pump, ηo=0.70 mechanical efficiency , ηm…

Q: The motor of the pimp consumes 1.05 hp of electricity. The pump increases the pressure of water from…

Q: 2 A 32m high down comar-tank exib high down comar-tank system operates at loobar. IF the quality of…

A: Given Volume, V = 32 m3 Initial pressure, P1 = 100 bar Quality, x = 0.5…

Q: A centrifugal pump lifts water against a static head Az = VEN m. The pipe setup has a constant…

A: Given: EN = 62 Δz=62=7.874 m hLS=620.3=3.45 mhLD=3md = 0.15 mw=0.015 mβ2=22°ηh=0.85N= 20*62 = 1240…

Q: A pump has overall efficiency of 70 %. It delivers 90 Ipm at 1000 rpm and 700 N/cm. If the prime…

A: η0=70%Q=90LpmN=1000 rpmp=700 Ncm2Tinput=12 KN-cm

Q: pump is installed in a pipe system, where at the suction side 1.0 m below the pump, an open…

A: It is required to determine total energy head

Q: Refer to the system curve drawn on this pump curve. If the pump is to move 1200 gpm, what is the…

A: Given: Q = 1200 gpm To find: Dynamic head at given flow rate using the plot.

Q: PUMP DISCHARGES 150 LITERS PER SECOND OF WATER TO A HEIGHTOF 80 METERS. IF THE EFFICIENCY IS 80% AND…

Concept explainers

Applied Fluid Mechanics

A fluid is a substance that is continuously deformed by the application of shear stress. The rate of deformation of a fluid depends on its viscosity. The fluid tries to flow when it interacts with some other system.

Question

100%

A centrifugal pump delivers 60 litres of water per second to a tank situated at a height of 20 metres.
If the overall efficieney of the pump is 70%, find the power required for the pump. (Ans. 16-8 kW)
1.

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Step by step

Solved in 2 steps with 2 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.

Similar questions

Include a free body diagram A pump is installed in a pipe system, where at the suction side 1.0 m below the pump, an open manometer reads a vacuum of 20 cm of mercury. The pipe is 10 cm in diameter and the flow is 35 L/s of water. Find the total energy at the location of the manometer, relative to a datum, through the pump. A. 12.74 m B. -4.67 m C. 2.56 D. -2.72 m
A pump is installed in a pipe system, where at the suction side 1.0 m below the pump, an open manometer reads a vacuum of 20 cm of mercury. The pipw is 10 cm in diameter and the flow is 35 L/s of water. Find the total energy at the location of the manometr, relative to a datu, through the pump. a.2.74 m.b.2.56 m.c.-4.67 m.d.-2.72 m.
In a steady adiabatic flow through a duct with no shaft/electrical work and no change in elevation and potential energy, the (A) enthalpy remains constant B inlet enthalpy is greater than the outlet enthalpy (C) outlet enthalpy is greater than the inlet enthalpy
For this system and Ywater = 62.4 lb/ft³, what is the (a) total horsepower required by the pump? and (b) the power transferred to the water (water horsepower)?
1. Determine the power delivered by the pump in kW 2. Determine the pressure head at point 2 in meters. 3. Determine the pressure head at point 1 in meters Thanks
1. A centrifugal pump has external and internal diameters of 300 mm and 150 mm respectively. The vane angles of inlct and outlet are 25 and 30° and the pump runs at 1450 r.p.m, If the velocity of flow through the pump is constant, find the work done per kN of water. (Ans. 20-2 kJ)
Two electric motors are being considered to drive a centrifugal pump. Each motor is capable of delivering 60 horsepower (output) to the pumping operation. It is expected that the motors will be in use 2,000 hours per year and the MARR = 8% per year. (1 hp = 0.746 kW) a. If electricity costs $X per kilowatt-hour, calculate the annual cost of electrical power for each motor b. What cost of electricity (S/kWh) makes the two pumps breakeven (i.e. have the same equivalent annual cost)? Assume repeatability and MVS = $0. c. Choose the graph to illustrate your answer to Part (b). d. Which motor should be selected? Click the icon to view the datatable for the additional information about two alternatives. Click the icon to view the interest and annuity table for discrete compounding when the MARR is 8% per year. a. The annual cost of electrical power for Motor A is $(xX). (Round to two decimal places.)
Two electric motors are being considered to drive a centrifugal pump. Each motor is capable of delivering 90 horsepower (output) to the pumping operation. It is expected that the motors will be in use 2,000 hours per year and the MARR = 5% per year. (1 hp = 0.746 kW) a. If electricity costs $X per kilowatt-hour, calculate the annual cost of electrical power for each motor b. What cost of electricity ($/kWh) makes the two pumps breakeven (i.e. have the same equivalent annual cost)? Assume repeatability and MVs = $0. c. Choose the graph to illustrate your answer to Part (b). d. Which motor should be selected? Click the icon to view the datatable for the additional information about two alternatives. Click the icon to view the interest and annuity table for discrete compounding when the MARR is 5% per year. a. The annual cost of electrical power for Motor A is $( XX). (Round to two decimal places.)
A pump discharges 50 tons of water per hour to a height of 8 m, overall efficiency of the pumping system being 69%, what is the input and output power?
In an external gear pump, if the delivery rate is 8 cm3/revolution, the prime mover's speed which is connected to the pump of with 2900 rpm,Determine The pump delivery in terms of litres per minute is
We have a system that must pump 195 GPM, at a height of 85 meters, and its losses byaccessories are 5% of their static load, please indicate the operating point and choose the impeller thatbest fits between the options of the graph A, B, C, D and F, indicate what is the expected returnof this pump, which would be the expected consumption in Hp.
A pump is installed in a pipe system, where at the suction side 1.0 m below the pump, an open manometer reads a vacuum of 20 cm of mercury. The pipe is 10 cm in diameter and the flow is 35 L/s of water. Find the total energy at the location of the manometer, relative to a datum, through the pump. A. -4.67m B. 12.74m C. -2.72m D. 2.56