A circular pile having a diameter of 0.44 m is 16.41 m long which is embedded in a layer of dense compacted sand having the given properties. Soil properties: Lateral pressure factor, K = 3.30 Nq = 60 Specific gravity, Gs= 2.67 Void ratio, e =1.15 Saturation above the GWT = 0.70 Ground water table (GWT) is located 3.87 m below the ground.

A circular pile having a diameter of 0.44 m is 16.41 m long which is embedded in a layer of dense compacted sand having the given properties. Soil properties: Lateral pressure factor, K = 3.30 Nq = 60 Specific gravity, Gs= 2.67 Void ratio, e =1.15 Saturation above the GWT = 0.70 Ground water table (GWT) is located 3.87 m below the ground.

Fundamentals of Geotechnical Engineering (MindTap Course List)

5th Edition

ISBN:9781305635180

Author:Braja M. Das, Nagaratnam Sivakugan

Publisher:Braja M. Das, Nagaratnam Sivakugan

Chapter15: Retaining Walls, Braced Cuts, And Sheet Pile Walls

Section: Chapter Questions

Problem 15.22P

See similar textbooks

Similar questions

A circular pile having a diameter of 0.33 m is 14.21 m long which is embedded in a layer of dense compacted sand having the given properties. Soil properties: Lateral pressure factor, K = 3.53 Nq = 99 Specific gravity, Gs= 2.61 Void ratio, e =1.21 Saturation above the GWT = 0.41 Ground water table (GWT) is located 3.58 m below the ground. Use unit weight of water = 9.81 kN/m3 Coefficient of friction = 0.41 Factor of safety = 3.98 Calculate the allowable capacity of the pile in kN.
The group pile below is to be built in normally consolidated clay. Calculate the consolidation settlement in cm. Cap Size: B = 4 m; L = 5 m Group Pile Dimensions: Bg = 3 m; Lg = 4 m ; cm³ Y = 1.8 gr Clay Parameters: Ysat = 2.gr 9 m 1 m 4 m cm3 m₂ = 3.75 * 10-3 m² /ton 150 ton Saturated Clay Sand
Evaluate the resisting capacity against axial load due skin friction of a concrete pile embedded into a layer of plastic clay given in the following conditions: Size of pile = 0.4 m square Depth of penetratian inta the clay layer = 40 m Unconfined compression strength (qu) af the clay = 200 KPa Ans. 6400 kN
Refer to Figure 18.26b. Let L = 15.24 m, fill = 17.29 kN/m3, sat(clay) = 19.49 kN/m3, clay = 20, Hf = 3.05 m, and D = 0.406 m. The water table coincides with the top of the clay layer. Determine the total downward drag on the pile. Assume that = 0.6 clay. FIG. 18.26 Negative skin friction
Refer to Figure 18.13. Given L1 = 1.5 m, L2 = 3 m; for the sand, =33, =16.5kN/m3, sat=19.0kN/m3; and, for the clay, c=50kN/m2, =0, sat=20kN/m3. Determine the depth of sheet pile required, allowing for a 50% increase from the theoretical estimate.
A 50 cm square precast pile is driven by 9 m into a sandy soil. The standard penetration test results, prformed on this ground, are given in the table below: Depth below ground surface (m) SPT (Nss) 1.5 3.0 4.5 4 6 6.0 12 12 20 24 35 39 If the skin resistance is equal to {T, = 2 x (average Nss along the pile shaft)) kPa. Compute the factor of safety available, if 1100 kN of compressive load is applied on this pile. 7.5 9.0 10.5 12.0
A 50 cm diameter precast pile is driven by 9 m into a sandy soil. The standard penetration test results, prformed on this ground, are given in the table below: Depth below ground surface (m) 3.0 4.5 6.0 7.5 9.0 10.5 12.0 SPT (N55) 6 12 12 20 24 35 39 1.5 4 If the skin resistance is equal to (ts=2 x (average Nss along the pile shaft)} kPa. Compute the number of piles that needed to support a total load of 4400 KN with factor of safety (2.5).
Determine the consolidation settlement of piles group shown below. Sand y = 105 lb/ft³ Groundwater table: 2V:1H Clay Clay (not to scale) (30 f Q = 500 Kip Δαίν Aσ(2) ∙3 ft 27 ft 21 ft (3), 40(3) 2V:1H 6 ft Clay = Ysat 48 ft e,, = 0.82 C₁ = 0.3 115 lb/ft³ 7. Rock Pile group: L = 9 ft: B₂ = 6 ft Ysat = 120 lb/ft³ -0.7 ea 12 ft C = 0.2 $6 it e Ysat = 122 lb/ft³ = 0.75 C = 0.25
In-situ stresses-Seepage condition ground level sheet Example: For the sheet pile which T is buried in sandy soil ,shown in 2.0m the figure below, find the total piling. water level and effective vertical stress at Points 0, 6, and 12?. 4.0m Note: Assume reasonable values for saturated and dry unit weight equipotential datum oollege Of I of the soil 3.0m flow line 3.0m Soil Mechanics : Lecture 2
Q1/ For the footing shown in Figure (1), estimate the pile group capacity. 0.6m dia bored pile Clay c=80 kN/m² y-17kN/m² S=1.5 m T L=12 m
A circular pile 0.45m in diameter and 15m long is embedded in a layer of dense sand. The soil has the following properties: Dry unit eight is 18 kN/m3 and saturated unit weight is 21 kN/m3 (water table is 4m below from the ground surface), Nq=85, k=1.25, tan αα = 0.45 and FS=2.5 a) Calculate the end bearing capacity b) Calculate the frictional resistance c) Calculate the allowable load
A frictional pile with a circular cross-section (diameter = D) is pushed into the soil %3D to a distance (L) and then it is subjected to an axial force (P) on its top end. Derive a formula to calculate the normal stress in any section x. P xx f N/mm2