A composite beam is made of two brass [E - 111 GPa] bars bonded to two aluminum [E - 72 GPa] bars, as shown. The beam issubjected to a bending moment of 250 N-macting about the z axis. Using a - 10 mm, b- 65 mm, c- 20 mm, and d- 45 mm, calculate(a) the maximum bending stress in the aluminum bars.(b) the maximum bending stress in the brass bars.AluminumBrassBrassAluminumAnswers:(a) OaiMPa(b) OerMPaSave for LaterAttempts: 0 of 1 usedSubmit Answer

Given:- a = 10 mm b = 65 mm c = 20 mm d = 45 mm BM = 250 N-m

A composite beam is made of two brass (E - 111 GPa) bars bondedt subjected to a bending moment of 250 N-macting about the z axis. (a) the maximum bending stress in the aluminum bars. (b) the maximum bending stress in the brass bars. Aluminum Brass Brass

A composite beam is made of two brass (E - 111 GPa) bars bondedt subjected to a bending moment of 250 N-macting about the z axis. (a) the maximum bending stress in the aluminum bars. (b) the maximum bending stress in the brass bars. Aluminum Brass Brass

Steel Design (Activate Learning with these NEW titles from Engineering!)

6th Edition

ISBN:9781337094740

Author:Segui, William T.

Publisher:Segui, William T.

Chapter1: Introduction

Section: Chapter Questions

Problem 1.5.6P: The data in Table 1.5.3 were obtained from a tensile test of a metal specimen with a rectangular...

See similar textbooks

Related questions

Q: -3 m 250 mm 200 mm The beam has a rectangular cross section with width b = 200 mm and height stress…

Q: Using the cantilever method, calculate for the magnitude of the moment reaction at support A.…

A: To use the cantilever method

Q: The cantilever bearn consists of a rectangular structural steel tube shape [E -29,000 ksi; I- 1640…

Q: 4. Given A vehicle changes velocity from 80.0 km/hr to 20.0 km/hr in 6.00 seconds. Required: Find…

Q: The stresses shown act at a point in a stressed body. The stress magnitudes are S, = 90 MPa and S, =…

Q: principal strain deformations, and the maximum in-plane shear strain distortion in a sketch. Ex =…

Q: Determine the maximum floor load that the simply supported interior stringer can carry based on the…

Q: n rectangular cantilever beam is Ising As=6-25mm h-250mm h Isi

Q: 0.08 m yakx 0.06m - p. locate the Centroid for the following areas

A: To find the centroid-

Q: A composite beam is constructed using a steel plate (15 mm x 170 mm) with two wood beams (75 mm x…

Q: simply supported beam has a maximum moment equal to 22 KN.m. The beam has a width of 200 mm and a…

Q: The cantilever beam consists of a rectangular structural steel tube shape [E = 29,000 ksi; | = 1520…

Q: E b W A а 3 1.1 m b = 1.7 m W = 224 N

Q: 3- The maintenance costs for a bridge with an expected 50 years life are estimated to be…

Q: Consider a point in astructural member that is subjected to plane stress. Normal and shear stresses…

Q: The internal shear force at a certain section of a steel beam is V=7.2kN. The beam cross section…

Q: 2 m 2 m E 2 m B 2 m 500 kg 4 m A

A: To find the force in each members-

Q: ists of a W14 × 34 structural steel wide-flange shape [E - 29,000 ksi; I = 340 in.4). is to compute…

Q: Reflection on Smart Hard Hat in Construction

A: Purpose: Hard hats are required when working in areas where there is a potential for injury to the…

Q: The stresses shown act at a point in a stressed body. The stress magnitudes are Sx=85 MPa and Sy =…

Q: KINDLY GET THE RIGHT ANSWER Given that B =1 m, L = 3 m, and Q = 110 kN, the soil characteristics…

A: The given data is shown below: B=1mL=3mQ=110 kNCs=15Ccσ'c=40 kN/m2

Q: Determine the amount of N, P2O5, and K2O

A: Fertilizer: - It is a chemical substance which is used to improve the quality of agriculture land…

Q: Q8. Glycerin of density (1250 kg/m³) and viscosity (0.72 Pa.sec) flows through a pipe of (80 mm) in…

A: As per our company guidelines we are supposed to answer only first 3 sub-parts. Kindly repost other…

Q: A square footing is shown below. The footing will carry a gross load of 700 kN. Using a factor of…

Q: The shown beam cross-section has f' 4,000 psi and f, neutral axis "c" (distance from the extreme…

A: Depth of neutral axis = Xu= Asfybα fc= 60000*5.0618*0.56*4000=7.529 in= 7.567 in

Q: PROBLEM 3: A trapezoidal canal having a base width of 40 m carries a discharge of 3.0 cu.m/s at a…

A: solution Given width b=40mts depth d=2mts side slope 2V to 1 H so the top width of the trapezoidal…

Q: For the beam and loading shown, use the double-integration method to determine (a) the equation of…

Q: What are the 5 types of construction?

A: The list of 5 Types of Construction in civil engineering as follows:-

Q: 13. Determine the design strength of the connection shown below. Only check for bolt shear, bearing…

A: Design strength : The lower value of a material's actual resistance obtained while considering the…

Q: A cyclist jumps off the 25° slope track at 5m height, and with the speed 20 m/s. Calculate the time…

Q: A simple curve connects two tangents AB and BC with bearings N 36°12' E and N 58°53' E respectively.…

A: solution Given two bearings N36°12'E and N58°53'Eso the deflection angle I…

Q: 1. Use slope-deflection method to solve the moments listed in ansSheet. And compute the displacement…

A: In slope deflection method ,first we need to find out the fixed end moment corresponding to each…

Q: Determine the rotation of point D of the projecting beam. IE is constant (By the method of virtual…

Q: WT305 x 41 standard steel shape is used to support the loads shown. Assume w - 56kN/m, LAB - 1.0m,…

Q: A simply supported timber beam with length L-5m carries a uniformly distributed load w - 8 kN/m.…

A: Given data in question Span member length UDL Cross section To find out Bending stress in…

Q: indicated in the figure. Using the equilibrium equation approach, determine the normal and shear…

A: Given data in question Stresses Angle To find out Normal and shear stresses

Q: В 5 kN-m

A: To find the thickness of shaft-

Q: Determine modulus of elasticity if bulk modulus 75 MPa and value of poisson ratio 0.32

A: Given data : The value of bulk modulus K=75 MPa The value of Poisson's ratio μ=0.32 To find :…

Q: Two pipes A and B meet at a junction to deliver a mixture of fluids to Pipe C. Water flows at a rate…

A: solution Given flow rate and density in pipe A Qw=297 Lsec and ρw=1000kgm3flow rate and density in…

Q: A triaxial test is performed on a cohesionless soil. The soil failed under the following conditions:…

A: c = 0 (cohesion less soil) σ3= confining pressure = 250 kpa∆σ = deviator stress = 450 Kpa To…

Q: A WT305 x 41 standard steel shape is used to support the loads shown. Assume w = 42 kN/m, LAB = 1.2…

Q: A rectangular cantilever beam shown supports its own deadload plus a factored concentrated load Pu…

Q: Find the angle @g

Q: or F = 500! 3 m 2 m 2 m of Determine and express the results in Cartesian vector 3. format: a. The…

Q: A simply supported beam with a span of 9.5m has a uniformly distributed dead load (including the…

A: step 1-

Q: For the beam and loading shown, use the double-integration method to determine (a) the equation of…

Q: Determine the force value if work done is 15 J and displacemnt is 3 m

A: Introduction : The value of force applied and value of displacement is known . With help of these…

Q: As figure shown, find the head loss between A and B if the velocity is 25 m/s. DA A PA= 29.43 N/cm…

Q: The stresses shown act at a point in a stressed body. The stress magnitudes are S, = 80 MPa and S, =…

A: Given data in question Normal stresses on element Angle To find out Normal and shear stress on…

Q: Design a laterally unsupported beam for the following data.

A: Given Data:Effective Span Leff=4.5mMax Bending Moment= 650kN-mMax Shear force= 300kNsteel of grade =…

Concept explainers

Types of Composite

Composite materials are formed by merging two components that have different chemical and physical properties. The merged output is termed as a composite, whose properties are completely different from the individual components. Composite materials also have better strength than the individual components.Composite materials usually have two main parts, reinforcement material, and matrix material. The matrix material acts as a binder and surrounds the fiber of another material that bears a much higher strength. This material is known as the reinforcement material. The matrix materials are usually high-strength additives resins, while the fibers of the reinforced material can be random, oriented, and in a mat format.Composite materials are also known as fiber-reinforced composite polymers because they are composed of the polymer matrix which is reinforced to laboratory-created fibers or naturally occurring fibers, such as glass fibers, carbon fibers, or aramid fibers. Under the application of external loads, the matrix material absorbs and transfers the loads to the fibers, these fibers in return provide good compressive strength, tensile strength, and stiffness to the fiber-reinforced composite materials.Depending upon the matrix and the reinforcement material, different properties can be induced to the fiber-reinforced composite materials, including good corrosion resistance properties. The most common matrix material is the resin while the glass fibers act as the reinforcement material. Strong fibers provide strength and stiffness to the composite materials while, a soft and flexible resin provides shape to the composite materials.

Question

A composite beam is made of two brass [E - 111 GPa] bars bonded to two aluminum [E - 72 GPa] bars, as shown. The beam is
subjected to a bending moment of 250 N-macting about the z axis. Using a - 10 mm, b- 65 mm, c- 20 mm, and d- 45 mm, calculate
(a) the maximum bending stress in the aluminum bars.
(b) the maximum bending stress in the brass bars.
Aluminum
Brass
Brass
Aluminum
Answers:
(a) Oa
i
MPa
(b) Oer
MPa
Save for Later
Attempts: 0 of 1 used
Submit Answer

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1

Step 2

Step 3

Step 4

Step by step

Solved in 4 steps

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, civil-engineering and related others by exploring similar questions and additional content below.

Similar questions

The data in Table 1.5.3 were obtained from a tensile test of a metal specimen with a rectangular cross section of 0.2011in.2 in area and a gage length (the length over which the elongation is measured) of 2.000 inches. The specimen was not loaded to failure. a. Generate a table of stress and strain values. b. Plot these values and draw a best-fit line to obtain a stress-strain curve. c. Determine the modulus of elasticity from the slope of the linear portion of the curve. d. Estimate the value of the proportional limit. e. Use the 0.2 offset method to determine the yield stress.
A copper strip (Ec= 105 GPa) and an aluminum strip (Ea = 75 GPa) are bonded together to form the composite beam shown. Knowing that the beam is bent about a horizontal axis by a couple of moment M= 33 N-m, determine the maximum stress in the aluminum strip and in the copper strip. Aluminum Copper 24 mm 6 mm 6 mm The maximum compressive stress in the aluminum strip is The maximum tensile stress in the copper strip is MPa. MPa (include a negative sign).
A composite beam is made of two brass [E = 97 GPa] plates bonded to an aluminum [E = 72 GPa] bar, as shown. The beam is subjected to a bending moment of 2420 N-m acting about the z axis. Assume b=64 mm, d1=36 mm, d2=13 mm. Determine: (a) the maximum bending stresses opy,Gal in the brass plates and the aluminum bar. (b) the stress in the brass obrj at the joints where the two materials are bonded together. Brass (2) d2 Aluminum (1) Brass (2) dz b Answers: (a) obr = i MPa, oal = i MPа. (b) Obrj MPa.
A composite beam is made of two brass [E = 96 GPa] plates bonded to an aluminum [E = 62 GPa] bar, as shown. The beam is subjected to a bending moment of 2260 N-m acting about the z axis. Assume b=53 mm, d1=48 mm, d2=14 mm. Determine:(a) the maximum bending stresses σbrσb⁢r, σalσa⁢l in the brass plates and the aluminum bar.(b) the stress in the brass σbrjσb⁢r⁢j at the joints where the two materials are bonded together.
An axial centric force of magnitude P = 450 kN is applied to the composite block shown by means of a rigid end plate. Knowing that h = 10 mm, determine the normal stress in (a) the brass core, (b) the aluminum plates. Aluminum plates (E = 70 GPa) 300 mm Brass core (E = 105 GPa) 40 mm h Rigid end plate 60 mm
A composite beam is made of two brass [E = 106 GPa] plates bonded to an aluminum [E = 60 GPa] bar, as shown. The beam is subjected to a bending moment of 1720 N-m acting about the z axis. Assume b=45 mm, d₁-53 mm, d₂-13 mm. Determine: (a) the maximum bending stresses Obr, Gal in the brass plates and the aluminum bar. (b) the stress in the brass Obrj at the joints where the two materials are bonded together. Brass (2) Aluminum (1) Brass (2) b ↓ d₂ d₁ d₂
An aluminum alloy [E = 69 GPa; v = 0.33; a = 23.0 x 10-6/°C] plate is subjected to a tensile load P. The plate has a depth of d = 215 mm, a cross-sectional area of A = 5100 mm2, and a length of L = 3.9 m. The initial longitudinal normal strain in the plate is zero. After load P is applied and the temperature of the plate has been increased by AT = 53°C, the longitudinal normal strain in the plate is found to be 2320 με. Determine: (a) the magnitude of load P. (b) the change in plate depth Ad. L Answer: (a) P = i (b) Δd = = i d KN mm
The composite bar shown is firmly attached to unyielding supports. An axial load P= 200 kN is applied at 20°C. Assume a = 11.7 um/(m °C) for steel and 23.0 um'(m °C) for aluminum. Find the reaction at the left support. a. find the reaction at the left supportb.find the stress at the steelc. find the stress at the aluminum
PROBLEM 6/6 F = 520 kN Determine the stress in each aluminum and steel bars after 0.2 mm F = 520 kN is applied. Note that a gap of 0.2 mm exist before the external load is Steel 280 mm applied and bars has equal distance with each other. Neglect the weight at the flat form. A = 1100 mm? E = 200 Gpa Steel Aluminum A = 2500 mm2 %3D E = 70 GPa %3D
A flat bar of aluminum alloy 25 mm wide and 5 mm thick is placed between two steel bars each 25 mm wide and 10 mm thick to form a composite bar 25 mm x 25 mm as shown. The three bars are fastened together at their ends when the temperature is 15℃. Find the stress in each of the materials when the temperature of the whole assembly is raised to 55 ℃.Steel: Es = 200 GPa; Coefficient of expansion = 1.2x10^-5/℃.Aluminum: Eal = 200/3 GPa; Coefficient of expansion = 2.3x10-5/℃.
An aluminum alloy [E = 74 GPa; v = 0.33; a = 23.0 x 10-6/°C] plate is subjected to a tensile load P. The plate has a depth of d = 265 mm, a cross-sectional area of A = 5300 mm², and a length of L= 4.2 m. The initial longitudinal normal strain in the plate is zero. After load P is applied and the temperature of the plate has been increased by AT = 57°C, the longitudinal normal strain in the plate is found to be 2920 με. Determine: (a) the magnitude of load P. (b) the change in plate depth Ad. L P Answer: (a) P = i (b) Δd = i kN mm
a) Determine the force P (in kN) required to stretch the Aluminum bar by 3mm. B) Determine the final width and thickness of the Aluminum bar. (1)