A composite drive shaft is made up of two sections: a solid steel core and a brass tube encasing the core. The steel core has a diameter of 80 millimeters, and the brass tube has a diameter of 100 millimeters. The maximum allowable shear stress for the steel is 100 megapascals (MPa), and for the brass, it is 50 MPa. What is the greatest torque (T) that can be safely applied to the shaft without exceeding the allowable shear stress in either material? 50 mm Brass 50 mm 40 mm Steel

A composite drive shaft is made up of two sections: a solid steel core and a brass tube encasing the core. The steel core has a diameter of 80 millimeters, and the brass tube has a diameter of 100 millimeters. The maximum allowable shear stress for the steel is 100 megapascals (MPa), and for the brass, it is 50 MPa. What is the greatest torque (T) that can be safely applied to the shaft without exceeding the allowable shear stress in either material? 50 mm Brass 50 mm 40 mm Steel

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

A composite shaft arrangement of brass and steel is shown below. The allowable shear stress are 100 MPa for steel and 50 MPa for brass. Find the maximum torque, T that can be applied on the shaft safety. 50 mm Brass 50 mm 40 mm Steel
The column above is subjected to axial loading only. Assume the following: • E= 29000 ksi G = 10000 ksi • = 986 in4 A = 60 in? • L= 20 ft • Grade 60 steel (60 ksi yield stress) • The column is fixed at the top and pinned at the bottom Which of the following is closest to the maximum normal stress the column can support (before yielding or buckling)? 167 ksi 24 ksi 42 ksi 60 ksi
Two shafts are connected end to end by means of a flanged bolt coupling as shown. The maximum shear stress is limited to 50 MPa in the shafts and 20 MPa in the bolts. If one shaft is solid of 100 mm diameter and the other is hollow of 120 mm external diameter, calculate the bolt diameter so that both shafts and the coupling are all equally strong in torsion. 120 mm 100 mm 200 250 mm mm Solid Hollow Flanged Bolt Coupling 24.17 mm B 27.14 mm C 21.74 mm D 24.71 mm
Assume the transformed steel section reaches its allowable bending stress first. Calculate the magnitude of the allowable bending moment that can be applied in this case. Answer: M- i Ib-in.
A flanged bolt coupling consist of 9 steel bolts evenly spaced around a bolt circle 300 mm. in diameter and 6 bronze bolts on a concentric bplt circle 200 mm. in diameter. What are the sizes of bolts diameters for steel and bronze, if the torque applied is 6,000 N-m and without exceeding the stress of 60 MPa in the steel and 40 MPa for the bronze? The ratio of the bolt diameter db / ds = 0.50. For steel, use Gs = 83 GPa and for bronze, Gb = 28 Gpa.
The 200-mm square aluminum block supports a compressive load of 300 kN. What is the normal stress acting on section a–a in MPa What is the shearing stress acting on section a–a in MPa The lapbelt assembly is to be subjected to a force of 800 N. What is the required thickness t in mm. of the belt if the allowable tensile stress for the material is 10 MPa?
2) A solid rod with the given dimension shown in Fig. Axial loads are applied at the positions indicated. Find the f a) The max Compressive stress in the system P-60 kN Aluminum A=400 mm b) The max Tensile stress in the system P-60 kN Steel A = 500 mm² Bronze A-200 mm² 4P 2.5 m 1.5 m 2.0 m 2P
1.6-2 A round bar of 10 mm diameter is made of alu- minum alloy 7075-T6 (see figure). When the bar is stretched by axial forces P, its diameter decreases by 0.016 mm. Find the magnitude of the load P. (Obtain the mate- rial properties from Appendix H.) P PROB. 1.6-2 7075-T6 d = 10 mm P
Two circular shafts are joined together between fixed supports to resist a torsional moment of 80 kN-m as shown. Determine the absolute value of the maximum torsional shear stress of the hollow steel shaft (in MPa). 20 IN-m Sm stcel hellw circalar duminum Selid circular D= 75 mny Do- IDO mn D> 80 mm G- D GPon 6- IS0 EPa
Determine the maximum load P that can be applied in the system consisting of a bent bar bolted at both ends through the fiberglass as shown. The diameter of the bent bar is 1/4” Ø, outside diameter of the washer is 7/8” Ø and the thickness of the fiber glass is 3/8”. The working shear stress between the fiberglass and the washer is 300 psi, and the allowable bearing pressure between the washer and the fiberglass is 550 psi.
The composite shaft shown in the figure consists of a bronze sleeve (1) securely bonded to an inner steel core (2). The bronze sleeve has an outside diameter of 35 mm, an inside diameter of 30 mm, and a shear modulus of G2 - 45 GPa. The solid steel core has a diameter of 30 mm and a shear modulus of G2 - 85 GPa. Assume L - 380 mm. The composite shaft is subjected to a torque of T- 800 N-m. Determine (a) the maximum shear stresses in the bronze sleeve and the steel core. (b) the rotation angle of end B relative to end A. (1) L B Answers: MPa (a) TI = MPa rad (b) PBIA =
The assembly consists of two red brass C83400 copper rods AB and CD having a diameter of 30 mm, a 304 stainless steel rod EF having a diameter of 40 mm, and a rigid member G. If the supports at A, C, and F each have a stiffness of k= 200 MN/m determine the average normal stress developed in the rods when the load is applied. A C -300 mm- 30 mm 30 mm B D G E 450 mm 40 kN 40 kN 40 mm F