A continuous and aligned fibrous reinforced composite having a cross-sectional area of 975 mm, then the area is subjectet to an extemal tensile load. If the stresses sustained by the fibre and matrix phases are 215 MPaand 5.38 MPa, respectively, the force sustained by the fibre phase is 76,800 N, and the total longitudinal composite strain is 1.58x10 then determine.

A continuous and aligned fibrous reinforced composite having a cross-sectional area of 975 mm, then the area is subjectet to an extemal tensile load. If the stresses sustained by the fibre and matrix phases are 215 MPaand 5.38 MPa, respectively, the force sustained by the fibre phase is 76,800 N, and the total longitudinal composite strain is 1.58x10 then determine.

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

A continuous and aligned fiber-reinforced composite having a cross-sectional area of 1200 mm² is subjected to an external tensile load. If the stresses sustained by the fiber and matrix phases are 152 and 2.27 MPa, respectively, the force sustained by the fiber phase is 72300 N, and the total longitudinal strain is 0.00143, determine the following: (a) The force sustained by the matrix phase (in N). i (b) The modulus of elasticity of the composite material in the longitudinal direction (in GPa). i N i (c) The modulus of elasticity for the fiber phase (in GPa). GPa i GPa (d) The modulus of elasticity for the matrix phase (in GPa). GPa
question 1 of 3 A1 meter length of rubber with a Young's modulus of 0.01 GPa, a circular cross-section, and a radius of 0.001 m is subjected to a force of 1,000 N. What is the new length of the rubber after the force is applied (assuming it doesn't break)? O 10.5 m O 32.8 m O 31.8 m O 1.83 m
1. An element of graphite-reinforced composite is completely dry and is constrained against any dimensional changes in the 1 and 2 directions, but it is free to expand in the 3 direction. The element absorbs 1.5% of its dry weight in the form of moisture. (a) What is the strain in the 3 direction as a result of the moisture absorption? Why is this strain different from the value given by B3AM? (b) What stresses develop in the element? Assume that moisture absorption does not influence the material properties.
Q2/ Apolmer must not fail when tensile stress of 125 Mpa is applied .if the surfuce energy of this polymer is 0.5 j/ m and modulus of elasticity of 3 Gpa Answer the following : 1. Convert j/m to N/ m 2. Determine the allowable length of crack in ( mm) before failure
At an axial load of 25 kN, a 50-mm-wide by 20-mm-thick polyimide polymer bar elongates 2.8 mm while the bar width contracts 0.29 mm. The bar is 190 mm long. At the 25-kN load, the stress in the polymer bar is less than its proportional limit. Determine (a) the modulus of elasticity. (b) Poisson's ratio. (c) the change in the bar thickness. Answers: (a) E= (b) v= (c) Athickness= i i GPa mm
At an axial load of 24 kN, a 35-mm-wide by 15- mm-thick polyimide polymer bar elongates 3.0 mm while the bar width contracts 0.15 mm. The bar is 230 mm long. At the 24-kN load, the stress in the polymer bar is less than its proportional limit. Determine (a) the modulus of elasticity. (b) Poisson's ratio. (c) the change in the bar thickness. Answers: E= = V = IN Athickness= i GPa mm
A tensile force of 200 KN is applied on a 0.02-m diameter and.2-m long rod. After applying the load, the diameter of the rod decreases to 0.01998 m and the length increases to 2.01 m. Assuming no permanent deformation occurs in that material, the modulus of elasticity (GPa) is?
Thank you for answering this question. Please you specify each step as soon as possible. Good Luck! Thank You. Consider a 60-mm cube made of graphite-reinforced polymer composite material that is subjected to a tensile force of 100 kN perpendicular to the fiber direction, directed along the 2-direction. The cube is free to expand or contract. Determine the strains (Ɛ11; E22, Ɛ33, Y23, Y31. Y12) using following material constants for graphite-reinforced polymer composite. E1 =155 GPa, E2 = E3 = 12.10 GPa U 23 = 0.458, D12 =V13 = 0.248 G23 = 3.20 GPa, G12 = G13 = 4.40 GPa
An elastoplastic material with strain hardening has the stress–strain relationshipshown in Figure 1.6(c). The modulus of elasticity is 175 GPa, yield strength is480 MPa, and the slope of the strain-hardening portion of the stress–strain diagramis 20.7 GPa.a. Calculate the strain that corresponds to a stress of 550 MPa.b. If the 550-MPa stress is removed, calculate the permanent strain.
A stress of 1 kPa in a polymer deceased to 0.98 kPa after six weeks. This polymer is to hold a bundle of steel rods for up to one year. If the stress is less than 1.5 kPa, the band will not hold the rods tightly. Determine the initial stress needed to hold the rods.
P2. Design a cylindrical thin-wall composite fuselage for storing compressed natural gas at a maximum operating pressure of 20 MPa. The pressure vessel is made by filament winding with fibres at ±45 degrees and is required to sustain three times the operating pressure without failure. The radius of the cylindrical pressure vessel must be 0.25 meters, and the length must be 2 meters. The maximum strengths of the composite ply are equal to 2000 MPa in the fibre direction and zero perpendicular to the fibre direction. Determine the minimum number of composite plies required to meet the design requirements. Hoop stress and longitudinal stress of cylinder are Answers: 38 plies (when tp=1 mm) t pr 21
A rectangular plate of composite material is formed with unidirectional fibres orientated at 30 degrees to the longitudinal axis. The composite material has properties in the principal material directions of E₁ = 150 GN/m², E₂ = 45 GN/m², V12 = 0.28, V21 = 0.37 and G₁2 = 75 GN/m². A stress of 60 MN/m² is applied to the plate on the longitudinal direction? What is the strain in this direction. Give you answer in micro-strain. Your Answer: Answer