A cylindrical container with a massless and frictionless piston is filled with water up to a height h, as shown in the schematic. What mass m should be placed on the piston so that the water flow rate through the opened valve doubles? Consider that piston area A₁ = 0.05 m2, valve area A2 = A₁/8, h = 0.9 m, Pwater = 1000 kg/m³, and g = 9.80 m/s².

A cylindrical container with a massless and frictionless piston is filled with water up to a height h, as shown in the schematic. What mass m should be placed on the piston so that the water flow rate through the opened valve doubles? Consider that piston area A₁ = 0.05 m2, valve area A2 = A₁/8, h = 0.9 m, Pwater = 1000 kg/m³, and g = 9.80 m/s².

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

The pump shown in the figure below delivers a head of 200 ft to the water. Determine the power that the pump adds to the water. The difference in elevation of the two ponds is 150 ft. Assume L = 300 ft, D = 0.75 ft. Ws = S HKL IN valve Pump = 5.0 KL=0.8 KL = 1.5 Pipe length = L Pipe diameter = D Pipe roughness=0 ft-lb/s or K₁ i Lexit 1.0 hp
SUPPLEMENTARY QUESTION The figure shows two reservoirs connected by a pipe. The discharge rate in the pipe is known to be equal to SN/100 (m3/s) (where SN is the sum of your student number). Calculate the height of the second reservoir (H2), and the pressure head, velocity head and elevation head at point 3 (mid-point of the pipe). Hi 300 m H datum A = SN/1000 %3D L = 100 x SN (m) %3D D = 0.3 m
SUPPLEMENTARY QUESTION The figure shows two reservoirs connected by a pipe. The discharge rate in the pipe is known to be equal to SN/100 (m³/s) (where SN is the sum of your student number). Calculate the height of the second reservoir (H2), and the pressure head, velocity head and elevation head at point 3 (mid-point of the pipe). Hi 300 m H2 datum A = SN/1000 L = 100 x SN (m) D=0.3 m Please solve these question my sn number 31
This is an open-top cylindrical tank* height of tank = 4 meters diameter of tank = 2 meters The tank floats in water. The draft is 2.5 meters. diameter of the standard orifice placed at the bottom = 80 mm C = 0.68 What is the time necessary to sink the tank when the orifice is opened?
An engineer sees a water flow through a 0.4 km long and 200 mm diameter pipe having a roughness of 0.0015 mm at 0.075 cubic meter per second. Assuming that the property of H2O is u = 0.001 Nm/sec and p = 1 g/cu.m. He is bored, so he wanted to calculate the following, help him. a. the pressure drop cause of friction b. velocity of H2O in the pipe c. find the Re?
A tank has two identical orifices in one of its vertical sides. The upper orifice is 4 m below the water surface and lowers one 6 m below the water surface. If the value of Cv for each orifice is 0.98, find the point of intersection of the two jets. Include a diagram in your solution. a.At horizontal distance of 6.60 m. b.At horizontal distance of 7.60 m. c.At horizontal distance of 8.60 m. d.At horizontal distance of 9.60 m.
For the Figure, the cover gate AB closes a circular opening 128.6 cm in diameter. The minimum mass equal to . . ton. Let h= 91 cm. ..... ... Mass=? A 50 cm Water 6 m الجواب إجابة
Three pipes are connected in parallel. The difference in heads in each pipe is 40 m.Pipes Diameter (cm) Length (m) Friction factor1 15 500 0.022 10 450 0.033 20 800 0.0253. Determine the flow in pipe 3.
The suction side of a pipe system is as shown in the figure. The pump discharges 495 gpm of water under a total head of 100 ft at 40°F. Atmospheric pressure = 32.7 ft of water. If the required NPSH is 9 ft, will there be a cavitation problem? Please note that 1 cfs equals 449 gpm. 12 ft 6 ft Diameter L = 300 ft Steel = 10 in 5
Pressure gage B is to measure the pressure at point A in a water flow. If the pressure at B в is 87 kPa, estimate the pressure at A, in kPa. Assume all fluids are at 20°C. ywater =9790 N/m', Ymercury =133100 N/m2, yoil =8720 N/m³ SAE 30 oil Gage B Mercury 6 cm 5 cm Water flow 11 cm 4 cm
one IMG_1085 The plastic block shown below measures I.5 m x/.s m x(.7 m and has a specific gravity of 0.38. The concrete block B (density = 2400 kg/m*) is suspended from the corner of the plastic block by means of a cable and the plastic block is thus floating in the lake (T = 15°C) in the orientation shown. Determine the volume of the concrete block (units of liters) noting that it does not rest on the bottom of the lake. Neglect the weight and volume of the cable in your analysis. %3D 1.7 m 0.5 m Water Cable
Four reservoirs have pipes that meet at a common junction. Their characteristics are as follows: (see table) If the friction factor, f = 0.015 for all pipes, determine the following: a. discharge of pipe Ab. discharge of pipe Cc. discharge of pipe D