a cylindrical disk with diameter 40 mm and thickness 2 mm is compressed stress = applied force/cross sectional area what load was placed on the disk when stress = 500MPa
Q: Tutorial Sheet Part 1 (Basics) A thin-walled pressure vessel has a diameter of 45mm, a wall…
A:
Q: 1. A circular cylinder with inside diameter of 10 cm which carries a compressive force equivalent to…
A: Given questions: 1. A circular cylinder with inside diameter of 10 cm which carries a compressive…
Q: • Dimensions: width, b = 54 mm, depth, d = 110 mm, and height, h = 284 mm. • The modulus of…
A: Given:b=54 mmd=110 mmh=284 mmE=3 GPav=0.45θ=70°∆d=0.40 mm
Q: a) If a pipe with an inner diameter of 36 mm is subjected to an axial load of 5.20 x 105 N and the…
A: a) Given: Inner diameter=36mm or 0.036mAxial load (F)=5.2×105NMaximum allowable stress…
Q: The rigid bar ABC supports a load of 21.1 kN at point C. A circular rod (diameter 25 mm) supports…
A: Given:
Q: For the figure shown, have the following information: Bar (1) made of bronze Bar (2) made of…
A:
Q: 6. For the following wire rope diameters of 6 x 19 type wire rope, with steel core, find the…
A: The list of all parameters related to 6×19 type wire rope, with a steel core is given as Now, take…
Q: Two steel wires support a moveable overheadcamera weighing W = 28 lb (see fgure part a) usedfor…
A: W=28lb α = 22° β = 40°diameter1=30milsdiameter2=35mils1mil=0.001in To-Find:- a) Tensile stresses σ1…
Q: An aluminum rod is rigidly attached between a steel rod and a bronze rod as shown below. Axial loads…
A:
Q: Question 1 D A 10kN 28kN + + 60kN 44kN + 120cm 80cm Ocm 40cm Figure 1 a) Draw a Free Body Diagram…
A:
Q: (PeP,<(100, 200) lbflin? m 1.00 Thickness -0.1-in -1.50 I FIGURE 5.21 A rectangle element under…
A: The limited component strategy (FEM) is a well known technique for mathematically settling…
Q: Q2 (a) A steel cable with nominal diameter 25 mm as shown in Table Q2(a) is used in a construction…
A:
Q: Question 5 A crank arm consists of a sold segment of length bi and diameter d, a segment of length…
A: Apply force equilibrium condition along x direction.
Q: A single bar has 3 different cross sections as shown below. The load P1 is equal to 25,500 Newtons…
A:
Q: we want to build a single-rail overhead crane in the workshop.when the load reaches the extreme…
A: Given: The extreme location of load, x = 1800 mm = 1.8 m The tensile stress in rope, σ = 600 MPa The…
Q: Refer to the figure below, what should be the minimum weight of W so that the block of 1000N will…
A:
Q: Q2) In Figure show the force- extension curve for three materials. a) Material b) Material c)…
A: Q)Given data To determine -> which materials has high ductiity, ultimate strength and…
Q: Question 2: The cross-sectional area for the lattice rods in the figure is A=120 mm2, the modulus of…
A: Solution
Q: A rectangular (3" x 5") rod has an axial (tension) load applied, P, of 300,000 lbs. The diameter of…
A:
Q: 1- the upper part in fig below is a steel and lower part is a cast iron , the load P shortens the…
A:
Q: The spar shown in the figure is wood (s.g.=0.62), 2 in by 2 in by 10 ft, and floats in sea water…
A: Buoyant force must balance the weight of wood and weight of steel for given configuration.
Q: A circular cylinder with inside diameter of 10 cm which carries a compressive force equivalent to…
A: As per our guidelines we are supposed to answer only one question in case of multiple questions…
Q: stress; (b) strain; (c) total deformation.
A:
Q: A flat bar is 3/8 inches thick and has a centrally located drilled hole of diameter D. The bar is…
A: The data given is, The thickness of the bar, t = 3/8 inches Tensile load on the bar, P = 4000 lb
Q: Q2) In Figure show the force- extension curve for three materials. a) Material b) Material c)…
A: Yield strength: It is the maximum stress which can be developed in a material without causing any…
Q: An aluminum rod is rigidly attached between a steel rod and a bronze as shown. Axial loads are…
A:
Q: A copper tube is rigidly attached between a steel rod and an aluminum rod. Axial loads are at the…
A: Answer: (a) Steel : A = 176.4706 mm2 ; d = 14.9896 mm. (b) Copper : A = 294.7368 mm2 ; d = 19.3720…
Q: For question 103A and 103B, the thin-walled cylindrical container shown below. Say p is the internal…
A: Internal pressure P=15 MPa Inside diameter d=20 mm Wall thickness t=10 mm Longitudinal stress in a…
Q: A rectangular plate with a hole is shown in fig that carries a tensile load. Stress value calculated…
A: Given that A rectangular plate with a hole is shown in fig that carries a tensile load. Stress…
Q: steel bar
A: C. No stress
Q: A body is subjected to multiple applied loads. The resultant stress at point location (0, 1, 4)…
A:
Q: cross section, side length b, and wall thickness t. The second is a round of diameter b and wa…
A:
Q: Based on the figure below compute for the smallest washer diameter. x = 19 mm bolt tensile stress =…
A:
Q: Question Two A steel flat of thickness 10 mm tapers uniformly from 60 mm at one end to 40 mm at…
A:
Q: Question 1 D B A 10kN 28kN 60kN 44kN 120cm 80cm Ocm 40cm Figure 1 a) Draw a Free Body Diagram for…
A: Part a): A free body diagram is a schematic representation of all the forces acting in a member.…
Q: Sketch a free-body diagram of each element in the figure. Compute the magnitude and direction of…
A: To sketch: The free body diagram of each element and compute the magnitude and direction of each…
Q: 36. A steel bar is heated from room temperature to 80oC while it is free to expand. The bar will…
A: Internal resistance offered by the object per unit normal area when external force is applied is…
Q: Q1A 30 cm square steel bearing plate lies between a 20 cm diameter wooden post and a concrete…
A: According to the given information:…
Q: Given the loading criteria in the figure below, find all reaction forces. |80 kN 30 kN/m 2m 3m 2m
A: A uniformly distributed load (UDL) is a load that is evenly distributed throughout the whole…
Q: Try One - scene 7 of 7 The bar has a 90 mm by 20 mm rectangular cross section. If P = 80 kN,…
A: Calculated force component perpendicular N and parallel V to a - a inclined surface area. And also…
Q: Ql- Compare the maximum stress induced into a rectangular plate 100mm long into x-axis direction,…
A: Given data :- Length = 100 mm Width = 50 mm Thickness = 10 mm Tensile load = 10 KN
Q: An aluminum rod is rigidly attached between a steel rod and a bronze rod as shown in the figure…
A: GIVEN DATA- FOR STEEL AREA=500mm2 , STRESS=200MPa FOR AL AREA=400mm2 , STRESS=115MPa FOR BRONZE…
Q: Answer True or False: For the mechanical structure shown in figure, the concrete pipe have weight…
A: Weight: It is a product of the mass of the object with the gravitational acceleration. The SI unit…
Q: Fig. 1.42 shows a system of three springs in series subjected to two axial loads. The stiffnesses of…
A:
Q: Question Two A steel flat of thickness 10 mm tapers uniformly from 60 mm at one end to 40 mm at…
A: “Since you have asked multiple questions, we will solve the one question for you. If you want any…
Q: Figure Q3 shows a steel bar of diameter 16 mm and length 600 mm subjected to axial forces If E =…
A:
Q: Question 1 The cube in Figure Ql made of 200 mm sides of a certain material is subjected to a…
A: Given: The side of the cube is a=200 mm, Volumetric stress =50 N/mm2, The bulk modulus is K=100x103…
Q: The rigid beam shown in Figure AN- 12 is suspended by three cables. The beam is horizontal prior to…
A: Draw free body diagram of beam
Q: a) Figure Q2a shows a hollow tube of rectangular cross-section subjected to an axial compressive…
A:
Q: A circular steel shaft with length, L (m) has an outer diameter, d2 (mm) and inner diameter, d1…
A:
a cylindrical disk with diameter 40 mm and thickness 2 mm is compressed
stress = applied force/cross sectional area
what load was placed on the disk when stress = 500MPa
Trending now
This is a popular solution!
Step by step
Solved in 3 steps with 1 images
- The hollow drill pipe for an oil well (sec figure) is 6,2 in. in outer diameter and 0.75 in. in thickness. Just above the bit, the compressive force in the pipe (due to the weight of the pipe) is 62 kips and the torque (due to drilling) is 185 kip-in. Determine the maximum tensile, compressive, and shear stresses in the drill pipe.A tube from aluminium with an outside diameter of 50 (mm) and a wall thickness of 5 (mm) is used as a compression member. If the axial normal stress in the member must be limited to 90 MPa, what is the maximum force (in kN) that the member can support.Q6 A spherical vessel of 1.6m inner diameter is constructed by joining two hemispheres with equally spaced bolts as shown in fig.3. The vessel will operate at an internal pressure of 600kPa. Calculate the vessel plate thickness t. Given the allowable stress for the sphere plate will equal 50MPa. If the same plate was used to make a cylindrical vessel to operate at the same internal pressure, find the cylinder maximum allowable diameter. ... المزيد A Ľ تعديل حذف 0 المفضلة Lo مشاركة
- 2. The tires of an agricultural tractor shown below are assumed to be 25 cm wide for the front tires and 40 cm at the rear tires. Ground contact of each tire is 15 cm. Calculate the compressive stress between each tire and the ground surface. Weight = 2,500 kg 15 cm 1.3m Point A 2.2 m 2R 2F1. Figure Q2a shows a hollow tube of rectangular cross-section subjected to an axial compressive load of 250 kN. The section dimensions are breadth, b = 0.12 m, depth, d = 0.05 m with an equal thickness on all sides, t = 0.003 m. Calculate the compressive stress σ in the tube. Give your answer in N/mm2 to 2 decimal places.Problem Solving: Show your Solution 1. A sculpture weighing 10,000 N rests on a horizontal surface at the top of a 6.0-m-tall vertical pillar. The pillar’s cross-sectional area is 0.20 m20.20 m2 and it is made of granite with a mass density of 2700kg/m3.2700kg/m3. Find the compressive stress at the cross-section located 3.0 m below the top of the pillar and the value of the compressive strain of the top 3.0-m segment of the pillar. 2. A 2.0-m-long steel rod has a cross-sectional area of 0.30cm2.0.30cm2. The rod is a part of avertical support that holds a heavy 550-kg platform that hangs attached to the rod’s lower end.Ignoring the weight of the rod, what is the tensile stress in the rod and the elongation of the rodunder the stress? 3. In a hydraulic press, a 250-liter volume of oil is subjected to a 2300-psi pressure increase. If the compressibility of oil is 2.0×10−5/atm,2.0×10−5/atm, find the bulk strain and the absolute decrease in the volume of oil when the press is operating.…
- A 2.4 diameter steel molding is lifted by 4 steel cables as shown. The mold weighs 3 kN/m. (a) what is the required diameter of wire that will not exceed the allowable stress of 120 MPa. and (b) if the wire diameter increase by 20%, find the vertical displacement of the molding. 24mA rectangular block of size 200mm x 100mm x 80mm (i.e. length x width x depth) is subjected to a tensile force of 300 KN in the longitudinal direction. A tensile force of 100 KN on the 200mm x 80mm faces and a compressive force of 80 KN on the 200mm x 100mm faces. Take E= 2 x 10³ N/mm² and Poisson's ratio as 0.3. Calculate the changes in the dimensions and change in volume of the block.Calculate the minimum diameter for a cylindrical vessel that is to carry a gas at a pressure of 10 MPa. The thickness of the vessel is 38 mm and the hoop stress is 83 MPa and the longitudinal stress is 40 MPa. 1 Add file
- PRELIMINARY DISCUSSIONS PME 412 - MACHINE DESIGN 1 PROBLEM: Find the values and plot the distribution of stress over the cross section of the upright of the figure. Locate the point of zero stress. 9,000 N 60 mm thick - 100 mm -50 mm100 kN A bracket in the form of a plate is fitted to a column by means of four rivets of the same size, as shown in Fig. A load of 100 kN is applied to the bracket at an angle of 60° to the horizontal and the line of action of the load passes through the centre of the bot- tom rivet. If the maximum shear stress for the material of the rivet is 70 MPa, find the diameter of rivets. What will be the thickness of the plate if the crushing stress is 100 MPa? 80 80 80 60° All dimensions in mm.Difficulty (3/5) Dimensions: a b 44 in 0.033 in segure and-cap effects 1900 Problem Statement: A cylindrical pressure vessel with dimensions given carries an internal pressure of 21 psi. Find the axial stress and the hoop stress induced in the wall of the vessel Answers: Oheep" be sure to include units with your answers