A cylindrical insulation for a steam pipe has an inside radius of 5 cm, an outer radius of 10 cm, and a thermal conductivity of 0.5 W/(m K). The inside surface of the insulation is at a temperature of 200 oC, and the outside surface is at 20 oC. Determine the heat loss per meter length of the insulation. O a. 185 W/m O b. 518 W/m O c. 581 W/m O d. 815 W/m

A cylindrical insulation for a steam pipe has an inside radius of 5 cm, an outer radius of 10 cm, and a thermal conductivity of 0.5 W/(m K). The inside surface of the insulation is at a temperature of 200 oC, and the outside surface is at 20 oC. Determine the heat loss per meter length of the insulation. O a. 185 W/m O b. 518 W/m O c. 581 W/m O d. 815 W/m

Principles of Heat Transfer (Activate Learning with these NEW titles from Engineering!)

8th Edition

ISBN:9781305387102

Author:Kreith, Frank; Manglik, Raj M.

Publisher:Kreith, Frank; Manglik, Raj M.

Chapter2: Steady Heat Conduction

Section: Chapter Questions

Problem 2.38P: 2.38 The addition of aluminum fins has been suggested to increase the rate of heat dissipation from...

See similar textbooks

Similar questions

2.38 The addition of aluminum fins has been suggested to increase the rate of heat dissipation from one side of an electronic device 1 m wide and 1 m tall. The fins are to be rectangular in cross section, 2.5 cm long and 0.25 cm thick, as shown in the figure. There are to be 100 fins per meter. The convection heat transfer coefficient, both for the wall and the fins, is estimated to be K. With this information determine the percent increase in the rate of heat transfer of the finned wall compared to the bare wall.
1.10 A heat flux meter at the outer (cold) wall of a concrete building indicates that the heat loss through a wall of 10-cm thickness is . If a thermocouple at the inner surface of the wall indicates a temperature of 22°C while another at the outer surface shows 6°C, calculate the thermal conductivity of the concrete and compare your result with the value in Appendix 2, Table 11.
1.4 To measure thermal conductivity, two similar 1-cm-thick specimens are placed in the apparatus shown in the accompanying sketch. Electric current is supplied to the guard heater, and a wattmeter shows that the power dissipation is 10 W. Thermocouples attached to the warmer and to the cooler surfaces show temperatures of 322 and 300 K, respectively. Calculate the thermal conductivity of the material at the mean temperature in W/m K. Problem 1.4
A hollow spherical steel has an inner diameter of 30cm and outer diameter of 37cm. It is covered with insulation of 5cm thick. The inner surface of the steel is kept at a constant temperature of 100°C and outside insulation is 30°C. The thermal conductivity of the material is 0.65 W/m-k. By what percentage will the rate of loss be decreased if the thickness of the insulation is increased by 4cm? O a. 16.65% O b. 83.35% O c. 79.57% O d. 20.43% O e. None
Steel pipe (outer diameter 100 mm) is covered with two layers of insulation. The inner layer, 40 mm thick, has a thermal conductivity of 0.07 W / (m K). The outer layer, 20 mm thick, has a thermal conductivity of 0.15 W / (m K). Pipes are used to delivering steam with a pressure of 600 kPa. The temperature on the outer insulation surface is 24 ° C. If the pipe is 10 m long, determine the following: (assuming that the conduction heat transfer resistance of the steel pipe and the vapor convection resistance are negligible). a. Hourly heat loss ... (kj / hr)b. temperature between insulation layers ... (° C.)
Steel pipe (outer diameter 100 mm) is covered with two layers of insulation. The inner layer, 40 mm thick, has a thermal conductivity of 0.07 W / (m K). The outer layer, 20 mm thick, has a thermal conductivity of 0.15 W / (m K). Pipes are used to deliver steam with a pressure of 500 kPa. The temperature on the outer insulation surface is 24 ° C. If the pipe is 8 m long, determine the following: (assuming that the conduction heat transfer resistance of the steel pipe and the vapor convection resistance are negligible). a. Heat loss per hour. = Answer kJ / hour. b. Temperature between insulation layers. = Answer ° C.
Steel pipe (outer diameter 100 mm) is covered with two layers of insulation. The inner layer, 40 mm thick, has a thermal conductivity of 0.07 W / (m K). The outer layer, 20 mm thick, has a thermal conductivity of 0.15 W / (m K). Pipes are used to deliver steam with a pressure of 600 kPa. The temperature on the outer insulation surface is 24 ° C. If the pipe is 8 m long, determine the following: (assuming that the conduction heat transfer resistance of the steel pipe and the vapor convection resistance are negligible). a. Heat loss per hour. = kJ / hour. b. Temperature between insulation layers. = ° C
Steel pipe (outer diameter 100 mm) is covered with two layers of insulation. The inner layer, 40 mm thick, has a thermal conductivity of 0.07 W / (m K). The outer layer, 20 mm thick, has a thermal conductivity of 0.15 W / (m K). Pipes are used to deliver steam with a pressure of 800 kPa. The temperature on the outer insulation surface is 24 ° C. If the pipe is 10 m long, determine the following: (assuming that the conduction heat transfer resistance of the steel pipe and the vapor convection resistance are negligible). a. Heat loss per hour. = AnswerkJ / hr. b. Temperature between insulation layers. = Answer ° C.
A steam pipe (inner diameter = 150 mm and outer diameter = 160 mm) havingthermal conductivity 58 W/m. °C is covered with two layers of insulation, ofthickness 30 mm and 50 mm respectively and thermal conductivities 0.18 W/m. °Cand 0.09 W/m .°C respectively. The temperature of the inner surface of steam pipeis 320°C and that of the outer surface of the insulation layers is 40°C.Determine the quantity of heat lost per meter length of steam pipe and layercontact temperature,
One vessel having a carbon-steel wall of thickness 5 mm carrying saturated steam and water at 423K. The vessel is insulated with magnesia of thickness 50 mm. If the ambient air temperature is 321 K, determine the heat loss from the vessel. Given: i. thermal conductivity of carbon steel is 52 W/m.K ii. thermal conductivity of magnesia is 0.5 W/m.K iii. surface coefficient of insulation surface is 3 W/m2.K
Water flows at 67 C inside a 2.5 cm inside diameter tube such that hi = 3500 W/m² .C . The tube has a wall thickness 0.72 mm with a thermal conductivity of 18 W/m.C. The outside of the tube loses heat by free convection with ho= 7.6 W/m².C. Calculate the overall heat transfer coefficient and heat loss per unit length to surrounding air at 15 C.
Calculate the quantity of heat conducted per minute through a duralumin circular disc 127 mm diameter and 19 mm thick when the temperature drop across the thickness of the plate is 5 degrees Celsius. Take the coefficient of thermal conductivity of duralumin as 150 W/(m-K).