A figure below is a 200-mm diameter pulley which was attached on a 60-mm diameter shaft and it applies a torque to the shaft equivalent to 2.2 kN-m. The allowable shearing stress in the key is 70 MPa. If the length of a key is 70 mm, determine the designed width of the key. ... F 0.20 m T = 2.2 kN-m 0.06 m 0.03 m

A figure below is a 200-mm diameter pulley which was attached on a 60-mm diameter shaft and it applies a torque to the shaft equivalent to 2.2 kN-m. The allowable shearing stress in the key is 70 MPa. If the length of a key is 70 mm, determine the designed width of the key. ... F 0.20 m T = 2.2 kN-m 0.06 m 0.03 m

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

A figure below is a 200-mm diameter pulley which was attached on a 60-mm diameter shaft and it applies a torque to the shaft equivalent to 2.2 kN-m. The allowable shearing stress in the key is 70 MPa. If the length of a key is 70 mm, determine the designed width of the key. 12 mm 14 16 15 mm
Determine the largest torque T which may be applied to end of the solid bar which is shown in the diagram below, knowing that the maximum allowable shear stress = 107MPa and G = 40GPa. Provide your answer in kNm with precision to two decimal points. B 40 mm TABLE 3.1. Coefficients for Rectangular Bars in Torsion a/b C₁ C₂ 1.0 0.208 0.1406 1.2 0.219 0.1661 60 mm 1.5 0.231 0.1958 2.0 0.246 0.229 2.5 0.258 0.249 3.0 0.267 0.263 4.0 0.282 0.281 5.0 0.291 0.291 N 10.0 0.312 0.312 مة 0.333 0.333
2. The lengths LAB = LBC = 200 mm and LCD = 240 mm. The diameter of parts AB and CD of the bar is 25 mm and the diameter of part BC is 50 mm. The shear modulus of the material is G = 80 GPa. What value of the %3D torque T would cause the angle of twist of the right end of the bar relative to the wall to be zero? 4 kN-m A 8 kN-m LAB B T LBC.
10. The hoisting beam assembly shown is supported by two 20- mm-diameter bolts at A and a 150 mm x 200 mm plate at B. In this problem, a = 1.2 m and b = 2.8 m. If the allowable tensile stress of the bolts at A is 112 MPa, which of the following gives the maximum safe value of W in KN? A. 45 C. 30 B. 60 D. 15 ZEIT 0 a BEEN H 8804 pe (cAPlate B to tried man 11 of 1911 b bell 110 mb llame lis To 102 W 20-102 bugil noitsuta
The lap joint shown in the figure is fastened by four 4 - in.-diameter rivets. Calculate the maximum safe load P that can be applied if the shearing stress in the rivets is limited to 14 ksi and the bearing stress in the plates is limited to 18 ksi. Assume the applied load is uniformly distributed among the four rivets. 7/8 in 7/8 in a. 20.56 kips O b. 15.23 kips Oc. 24.74 kips O d. 27.88 kips (
PROBLEM 2: What torque can be applied without exceeding the shearing stress of 65 MPa in the botts? Bolt diameter = 12 mm 83 R₁ R2 R₁ = 200.5mm R₂ = 150.5mm 23 = 100.9mm
A two pinned end bars AB (Copper), ? = 850 ??2, ? = 120 ??? and BC (Aluminum), ? = 1000??2, ? = 70 ??? is subjected to a horizontal force of 100 ?? applied at pin B as shown in the figure, determine the horizontal displacement of pin B.
Question 1 The same torque is applied to two tubes with identical metal sheets, determine the ratio of T circle/Tsquare of the shear stresses. Given: r= 14 mm, S = 19 mm, and t = 2.84 mm. 43 FETOO KA F1 F2 FS FB F7 F8 ESC T H.
1. The compound shaft shown in the figure is attached to rigid supports. For the bronze segment AB, the maximum shearing stress is limited to 8000 psi and for the steel segment BC, it is limited to 12 ksi. Determine the diameters of each segment so that each material will be simultaneously stressed to its permissible limit when a torque T-12 kip-ft is applied. For bronze, G = 6x106 psi and for steel, G = 12x10 psi. Bronze Steel 4 ft 6 ft THARAN
Given the clevis shown, P=25KN. If the shearing stress is limited to 60 MPa, what is the diameter of the bolt in mm?
Two forces, each of magnitude P, are applied to the wrench. The diameter of the steel shaft AB is 15.3 mm. Determine the largest allowable value of P (in N) if the shear stress in the shaft is not to exceed 87.95 MPa and its angle of twist is limited to 5.41°. Use G = 80.32 GPa for steel and L= 433 mm. Round off the final answer to two decimal places. ... P -300 mm P- B L A
A:Y 211O 2_531929016114... -> A rod is composed of an aluminum section rigidly attached between steel and bronze sections, as shown in Figure below. Axial loads are applied at the positions indicated. If P = 11 KN and the cross sectional area of each rod is 312.5 mm, determine the stress in each section. 4P Steel Bronze |Aluminum 609.6 mm 914.4 mm 762 mm