A five-story building has interior columns spaced 8m apart in two perpendicular directions. Given design loads: Roof: DL= 5 kPa LL=0 Floor: DL= 7 kPa (typical each floor) LL= 2.4 kPa (3rd, 4th and 5th floor) LL= 6 kPa (2nd floor) A. What is the total axial load on the column at second floor due to service live load, KN B. What is the total dead load on the column at ground floor in KN C. What is the total axial dead and live load at the column at ground floor in kN

A five-story building has interior columns spaced 8m apart in two perpendicular directions. Given design loads: Roof: DL= 5 kPa LL=0 Floor: DL= 7 kPa (typical each floor) LL= 2.4 kPa (3rd, 4th and 5th floor) LL= 6 kPa (2nd floor) A. What is the total axial load on the column at second floor due to service live load, KN B. What is the total dead load on the column at ground floor in KN C. What is the total axial dead and live load at the column at ground floor in kN

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

Given the floor layout below. Assume this is an upper story in a multistory office building. Perform live load reduction as appropriate. The floor is subjected to service (i.e. unfactored) superimposed dead load of 6.94 kPa and L = 3.24 kPa. Concrete weighs %3D 23.6 kN/m3. Typical interior floor beam is 326 x 649 mm. Slab thickness is 143 mm. Columns are 352x352 mm square. Determine the maximum factored bending moment (in kN-m) on a typical interior floor beam (secondary) assuming simply supported at both ends. 9-75 m 9-75 m 9-75 m 2 @ 6m 2 (@ 6 m 2 @ 6 m 6 m 12 m 12 m 12 m 12 m
Design economical spacing of 10 mm diameter stirrups for the beam which carries the loads shown. Design shear reinforcement of prestressed beam with the following properties listed. Properties: f’c = 28 MPafy = 276 MPaAps = 800 mm2Ds = 10 mmDm = 18 mmfse = 800 MPafpu = 1500 MPafpe = 860 MPaPe = 250 kN
A TIMBER BLOCK "B x B" mm SQUARE IS REINFORCED ON OPPOSITE SIDES BY A "B" mm AND 't' mm THICK STEEL PLATES. DETERMINE THE THICKNESS 't' SO THAT THE ASSEMBLY WILL SUPPORT AN AXIAL LOAD OF 1000 KN WITHOUT EXCEEDING A MAXIMUM TIMBER STRESS OF 12 MPa OR A MAXIMUM STRESS IN STEEL OF 350 MPa. MODULUS OF ELASTICITY OF STEEL AND TIMBER ARE 210 GPa & 7 GPa RESPECTIVELY. B t B t PROB 04
4.1 A simply supported beam is reinforced with 5-ϕ25 mm at the bottom and 2-ϕ20 mm at the top of the beam. Concrete covering to centroid of reinforcement is 70 mm at the top and 64 mm at the bottom of the beam. The beam has a gross depth of 450 mm and gross width of 300 mm. fc’= 28 MPa, fy = 415 MPa. Assume bars laid out in single layer. Calculate the following if the limiting tensile steel strain is 0.004 for a ductile failure: Calculate: Depth of the neutral axis from the extreme concrete compression fiber to the nearest whole number = ____?___ mm
The roof on the building in has a slab that is 175mm thick. The beams are 300 mm. wide and have a total depth of 400 mm., the bay dimensions are 6 m. in the X direction and 6.5 m. in the Y direction, and the superimposed service dead load is 0.29 KPa. Calculate the slab factored load in KPa. Use NSCP provisions for Live Loads.
4.3 A simply supported beam is reinforced with 5-ϕ25 mm at the bottom and 2-ϕ20 mm at the top of the beam. Concrete covering to centroid of reinforcement is 70 mm at the top and 64 mm at the bottom of the beam. The beam has a gross depth of 450 mm and gross width of 300 mm. fc’= 28 MPa, fy = 415 MPa. Assume bars laid out in single layer. Calculate the following if the limiting tensile steel strain is 0.004 for a ductile failure: Calculate: Maximum service uniform live load over the entire span in addition to a DL = 20 kN/m (including the weight of the beam) if it has a span of 6 m = _____?____ kN/m (to the nearest whole number)
4.2 A simply supported beam is reinforced with 5-ϕ25 mm at the bottom and 2-ϕ20 mm at the top of the beam. Concrete covering to centroid of reinforcement is 70 mm at the top and 64 mm at the bottom of the beam. The beam has a gross depth of 450 mm and gross width of 300 mm. fc’= 28 MPa, fy = 415 MPa. Assume bars laid out in single layer. Calculate the following if the limiting tensile steel strain is 0.004 for a ductile failure: Calculate: Design strength of the beam section to the nearest whole number = ____?___ kN·m
III. A simply-supported rectangular concrete beam with a width of 300mm wide, 600 mm total depth, and 5.8 m long, is needed to accommodate both ceiling height clearance below and the superimposed loads. If f' = 28 Mpa and steel 415 Mpa, fy = 13) what is the allowable resisting moment of the beam without 300 mm stressing the concrete beyond 0.45f"c and steel 0.60f,? Use the transformed area method and rn 8 65 mm 2 #25mm 535 mm 600 mm 14) what is the allowable resisting moment of the beam using the strength design method. 4 #32 mm 65 mm 15) Compare the results of (a) and (b) and comment your observation.
3rd: A simply supported 12-m span beam, 300-mm wide by 550-mm deep, is pre- stressed by straight tendons with Aps = 774 mm² located 70 mm from the bottom at an initial prestress of 1.10 GPa. What maximum service uniform live load can the beam support in addition to its own weight if allowable tensile stress in concrete 0.5 x square root of f'c is permitted. after 17% loss Write your answer in 2 decimal places only. Use fc = 30 MPa unit weight of concrete 24 kN/cu.m. Sign convention is (+) tension, (-) compression. Indicate the sign in your final answer.
(a) The detached servant room of a quarter is having internal size of 3.0mxx4.50m. It is to be covered by a roof of RCC. The dead load on roof 4.5kN//m^(2) and the live load is 1.50kN//m^(2) Design the slab by I.S. Code method. Assume grade of concrete as M25 and grade of Steel as Fe415.
A TIMBER BLOCK “B x B” mm SQUARE IS REINFORCED ON OPPOSITE SIDES BY A “B” mm AND ‘t’ mm THICK STEEL PLATES. DETERMINE THE THICKNESS ‘t’ SO THAT THE ASSEMBLY WILL SUPPORT AN AXIAL LOAD OF 1000 KN WITHOUT EXCEEDING A MAXIMUM TIMBER STRESS OF 12 MPa OR A MAXIMUM STRESS IN STEEL OF 350 MPa. MODULUS OF ELASTICITY OF STEEL AND TIMBER ARE 210 GPa & 7 GPa RESPECTIVELY.
A rectangular beam 250mm wide, 500 mm deep is reinforced at the bottom with 4-20-mm-diameter bars and at the top with 2-16-mm bars. Concrete cover to bar centroid at the top is 80mm and at the bottom is 70mm. Use concrete strength f’c=21 MPa and steel yield strength fy=415MPa for 20-mm bars and fy=275MPa for 16mm bars. - Determine the limiting tensile stress ratio for a tension controlled condition in positive or negative bending with the given material strengths. - Determine the design moment capacity of the beam in positive bending in kN.m (whole number) - Determine the design moment capacity of the beam in negative bending in kN.m (whole number)