Answered: A force of 800 N is applied on a rigid…

A force of 800 N is applied on a rigid bar as shown in the figure. The moment of F about origin O in clockwise direction is. F 4 m 60° Select one: a. 732 N.m b. 2771.3 N.m c. 3732 N.m d. 1000 N.m

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Related questions

Q: 1.5 In this figure, force F is pulling the rope (wrapped around the drum). There is no slippage…

A: 1.5 ) C 1.6) B 1.7) B

Q: par Tomat. A section of a reinforced concrete elevator shaft is shown in the figure. Compute the…

A: E = 5000 x fc

Q: 03 A F1 = 1300N, F, = 1850N, F; 3500N O1 = 70°, 02 155°, 03 = 200° The point A is acted upòn by…

Q: 6. A block weighing 100N is held on a 40" incline by a bar attached to a 150N block on a horizontal…

Q: Calculate the plastic moment (kN-m) of the cross-section about the horizontal axis. F, = 248 MPa. 50…

Q: For the figure shown knowing that a = 1.00 cm and b = 4.00 cm, determine: a) The centroid of the…

Q: mpute the resultant of the concurrent forces shown in N. P1 = 138 N, P2 = 403 N, = 330 N, 01 = 30…

Q: Q2/ A square plate of 10 cm side is subjected to five forces, applying at the corners, the mid-…

A: Given data in question Square with side 10 cm Vertical and horizontal point loads Angles To find…

Q: SITUATION. To prevent the ladder from sliding down, a person exerts a horizontal force F at C. L2 B…

A: Given, L1 = 1.5 m L2 = 4.5 m α=40°

Q: An overhang beam carries a concentrated load, triangular load and uniformly distributed load as…

A: Given; load w=180 KN/m ans a=1.8 m and b=4 mmoment at roller B MB=−2700 kN.m…

Q: If r ={3 i + 6j} m and F = {20 i + 40 j + 40 k} N, Calculate the moment of F about the y-axis?

A: Given data Force components Radius components To find Moment

Q: 30° 16° 44° x (+) q(+) p(+)

Q: Problem 2. Calculate the moment produced by each force about point A using M=Fd and the right hand…

Q: Problem 1: The bar shown is in equilibrium. Determine force P, T, and R. R 280N 3n 5m 3m 3m PE GOON

Q: Using the triple scalar product to determine the moment of the 750 N force about lineOC, you could…

A: To choose the position vector that can not be used to determine the moment of the 750 N force about…

Q: (b) Prove the equation for moment of inertia for Figure Q3(b) ~gainet axis x and y as; I = bh³/36 ly…

Q: 17- Calculate the value of 810 for the solution of the system given in the figure with the force…

Q: Area Moment Method For the given cantilever beam, (a) Compute the rotation at the free end A, in…

Q: MA = 12 kN .m w = 3 kN/m В 6 m Write the equations for moment as a function of distance x along the…

A: To write bending moment equation

Q: 20° F= 10 N 250 mm B 60° 37.5 mm

A: Draw FBD: ∵v250=sin60ov=250sin60o=216.5 mm∵vu=tan60ou=216.5tan60o=124.9 mmtotal vertical…

Q: 7. The sports car, having a mass of 1700 kg, travels horizontally along a 20 banked track which is…

A: Given data: Mass of car=1700 kg Radius of curvature=100 m It is asked to determine the normal…

Q: 1. In the Figure, determine the force P necessary to start the V-shaped wedge to the right if the…

Q: Situation V. A jet of water is deflected 60° by a frictionless vane moving with a constant velocity…

Q: For the beam loaded as shown, determine the beam deflection at point C. Assume that E = 25500 ksi…

A: Intensity of UDL (w) = 3.2 kips/ft Intensity of point load (P) = 36 kips Young's modulus of…

Q: Determine the spin and arrow equations for the next beam. If any constant is worth zero you must…

Q: b) Wire AB suspends a load of 268 N at Point B. Determine the magnitude of the force P required to…

A: step 1-

Q: From the given frame shown in the figure with a constant value of El=3970 KN- sq. m., determine the…

Q: The point P in the figure travels on the parabola (with focal distance f = 0.5 m) at the constant…

A: Given that The equation of the path is 2y = x2 The value of the focal distance is f = 0.5 m The…

Q: Required information Write the equations for shear and moment between points Band Cas a function of…

Q: PROBLEM 2: EQUILIBRIUM OF FORCE SYSTEM IN SPACE Find the forces in elements AB, AC, and AO. B 7 5. 7…

A: Find the forces in elements AB, AC, and AO.

Q: 8. In the following picture if anti-clockwise direction is positive then what is the moment arm and…

A: Given data- Anticlockwise direction is positive.

Q: F В F3

Q: 1. The rectangular plate is rotating about its corner axis through O with a constant angular…

Q: Shown below is the cross-section of a bridge pier. Knowing that the cross-section is symmetric and…

A: Given Data: The total width of the bridge pier is b=3.2 m. The total depth of the bridge pier is…

Q: D. 90 N 220 N B 180 N A 220 N 100 mm 100 mm

A: Answer:- In this problem we will divide the force into components . Then we will…

Q: Problem: In the figure shown, determine the value of P acting to the left tat is required to pull…

Q: If D KN and E kg, calculate the resultant of the two applied forces in pounds and its direction fron…

Q: the force system shown, determine the magnitud the resultant force. 5ON 240 N.m 45 75N [im 64r 40N…

Q: 9. Determine force P for impending motion to the left if the coefficient of friction for all surface…

A: Free body diagram of block B:

Q: An indeterminate beam carries different types of loads as shown in the figure. Using Moment…

Q: Activity 1. In the Figure, determine the force P necessary to start the V-shaped wedge to the right…

Q: 04. Completely determine the resultant of the force system shown in figure, locate it with respect…

Q: 6. Determine the slope at point C of the frame shown in the figure. The support A is fixed. Take E-…

A: To find slope at C

Q: 18. An elevator with a mass of 1500 kg descends with an acceleration of 2.85 m/s². What is the…

Q: SITUATION. A pole supported at point O is subjected to forces as shown. 2kN 2m 2m 2m 5m 8kN 6kN…

Q: The 700-N force is applied to the 100-kg block, which is stationary before the force is applied.…

Q: The 300-N block in the figure is at rest on the rough horizontal plane before the force P is applied…

A: Figure is as shown

Q: 1. 1. Find the value of F and a if T = 450 N, P = 250 N, B = 30°, and the resultant is 300 N acting…

Q: Problem 1: The bar shown is in equilibrium. Determine force P, T, and R. R 5m 5n 280N 3n 5m 3n 5m…

Concept explainers

Graphical Methods

The graphical method is a method of solving equations involving more than one variable using the Cartesian coordinate system. In civil engineering, the use of the graphical method is limited to the problems involving two variables. The graphical method has a great impact in solving the questions regarding engineering mechanics.

Question

A force of 800 N is applied on a rigid bar as
shown in the figure. The moment of F about
origin O in clockwise direction is.
F
4 m
60°
Select one:
a. 732 N.m
b. 2771.3 N.m
c. 3732 N.m
d. 1000 N.m

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

This is a popular solution!

SEE SOLUTION Check out a sample Q&A here

Step 1

Step 2

Step 3

Step 4

Step 5

Trending now

This is a popular solution!

Step by step

Solved in 5 steps with 5 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, civil-engineering and related others by exploring similar questions and additional content below.

Similar questions

3. In the figure below, a force F passing through C causes a clockwise moment of 217N-m about A and a clockwise moment of 96N-m about B. Determine the force and its x-intercept ix. A 2 m Fx+c Action Line of F .....I.....-. 3 m F, Fx D в ix IF, 5 m.
A A sp wt = y C b 10. Find the moment about AB of the force acting on one side of the vertical surface ABC of figure in problem no. 9, y = 9000 N/m. Ans. 1125 b2h2 N.m
0.3 m mathalino.com B 0.3 m Figure P-226 Given that F=1000Kn and P-1434. Determine the following: a. Components of forces F and P b. Moment at Point A, B, C, and D c. Moment at the Tail of Force F d. Moment at the Tail of Force P e. Moment at the Head of Force F f. Moment at the Head of Force P C. mathalino,com P.
300N 400N 45° 30 A200N Find F and e if the force sysem above is in a state OF Statc equilibrium.
275 N 1600 N 0.5 1.5 m 1.8 m Situation 4. The frame shown with a braked pulley is acted upon by four forces. If the resultant of the forces passes through point A A. 14. Determine the magnitude of the unknown tension T2. c. 877.885 N 1.25 m B. a. 785.996 N b. 846.559 N d. 731.792 N 50° 15. Determine the magnitude and direction of the resultant force R. a. R= 564.299 N, OR = 0.254° b. R= 797.831 N, OR = 54.702° d. R= 829.067 N, OR = 14.383°7 0.6 m c. R= 685.914 N, OR = 75.617°À T2 650 N
Problem 4 In the frame here, the Calculate reaction forces Dr. Dy and also the forces and moment in point C of the frame. Hint: the trapezoidal force is made of a uniform 300 lb/fr plus a triangular force from 0 to 300. 300 lb 10° /fr *. A 4' 600 B 16/fx 9° C
Three control rods attached to a lever ABC exert on it the forces shown. Take F = 144 N, the distance xx = 767 mm, and the distance yy = 533 mm, the moment M is applied counterclockwise at point B with magnitude of 89 N.mm. Determine the value of equivalent moment in N.mm at B. 2.4*F N 55 YYmm 2*FN 20° XXmm 130 20 FN A O a. 200160.98 O b. -95872.72 O c. -173966.56 O d. 200249,98 O e. 200249.98 Question 6
4/70 A force P is applied to the midpoint D of link BC. State the value of the couple M which would render (a) the horizontal force transmitted by pin B zero and (b) the vertical force transmitted by pin B zero. M R 45 B 30 Problem 4/70
Using Area Method Problem 6: Draw the shear and moment diagram. 900 N 400 N 60 N/m D B C. -6 m- +4 m+ а. Determine the shear value at 5 m from A. b. Determine the moment value at 13 m from A. Determine the location of point of inflection. d. What is the value of the maximum negative moment? С.
Q1): Determine the moment of the force system of figure below: (a) with respect to point O. (b) with respect to point A. 30 30° 10b -30 31 206
Determine the Moment of a Force at A. Consider clockwise to be positive. a.) 0 b.) -12/√2 c.) None of the above d.) 12√2 e.) 12/√2
1. Determine the Moment due to force F about: a. Point O b. Point B Note: The thickness of the beam is NOT negligible and is given in the image. Y ///// F=225N 9m 3m Th 5m B 2m O