A forged steel link with uniform diameter of 30mm at the centre is subjected to an axial force that varies from 40KN in compression to 160 kN endurance strength of the steel material are 600MPA,420 MPa and 240MPA respectively. Find FOS against fatigue endurance as per Soderberg's criterion.

A forged steel link with uniform diameter of 30mm at the centre is subjected to an axial force that varies from 40KN in compression to 160 kN endurance strength of the steel material are 600MPA,420 MPa and 240MPA respectively. Find FOS against fatigue endurance as per Soderberg's criterion.

Mechanics of Materials (MindTap Course List)

9th Edition

ISBN:9781337093347

Author:Barry J. Goodno, James M. Gere

Publisher:Barry J. Goodno, James M. Gere

Chapter7: Analysis Of Stress And Strain

Section: Chapter Questions

Problem 7.6.11P: -11 A rubber cube R of a side L = 3 in. and cross- sectional area A = 9 in2 is compressed inside a...

See similar textbooks

Related questions

Q: A rectangular steel block is 4inches long in the x direction, 2inches long in the y direction, and…

Q: A prismatic bar with a circular cross section is loaded by tensile forces P 65kN. The bar has length…

A: Given, Initial length of the bar, Li=1.75 m Initial diameter of the bar, di=32 mm=0.032 m Applied…

Q: The figure below are timber planks joined together by a bolt with the corresponding measurements.…

A: Given data: τw=10 ksiσb=20 ksid=34 in Need to determine the maximum safest value of P.

Q: Links (1) and (2) support rigid bar ABCD shown in the figure. Link (1) is bronze [E = 15,200 ksi]…

Q: Q.3) A W8 X 24 steel column of 7-ft effective length supports an eccentric load as shown below. The…

A: Given Data:- W 8×24 steel column Effective length le=7 feet…

Q: A solid circular bar is surrounded by a layer of copper rigidly attached to it, the assembly is…

Q: Steel rod (E:200 aPe) is loaded axially with tensice force of 100 KN. Find the sesess in the sod and…

A: Given, Young's modulus of steel rod = E = 200 GPa = 2 x 105 MPa Tensile force = 100 kN = 1 x 105 N…

Q: A solid copper bar of circular cross sectionhas length L =1.25 m and shear modulus of elasticityG =…

A: Shaft is designed on the basis of following two criteria:- Strength Criteria According to Strength…

Q: (7) The figure shows the free body diagram of a connecting link portion having stress concentration…

Q: A steel rod placed between two walls is an exact fit and is stress-free at 20 degrees Celsius. Find…

A: The temperature at which the compressive stress becomes 100 MPa is 62.7350 ℃.

Q: 3. Find the ratio of crippling loads by Euler's and Rankine's formulae for a hollow strut of 40 mm…

A: d0=40 mm di=30 mm I=π64404-304I=85902.924 mm4σyt=300 MpaE=200 Gpaa=17500

Q: A steel rod is stretched between two rigid walls and carries a tensile load of 5000 N at 20°C. If…

A: Given: The tensile load on the steel rod is P=5000 N. The initial temperature of the rod is…

Q: A rectangular steel block is 4inches long in the x direction, 2inches long in the y direction, and…

A: Solution to first three sub-parts as per our company policy:

Q: The figure below is a schematic drawing of a shaft that supports two V-belt pulleys. The loose belt…

A: Given, The yield strength of the material, sy=300 MPa The ultimate strength of the material, su=520…

Q: A load P is supported by a structure consisting of rigid bar ABC, two identical solid bronze [E =…

Q: A 1 m length bar of square cross section with side length 2cm, . is fully supported at one end and…

A: To find: The maximum force that bar can sustain elastically. Given: The length of the bar is l=1 m.…

Q: The mechanism shown

A: Write the expression for the compressive reaction force from the support when the stress in the…

Q: Q 3 A square steel bar 50 mm on a side and 1 m long is subject to an axial tensile force of 250 kN.…

Q: 2. A rigid bar of negligible weight is supported as shown in the figure. If W = 60 kN, compute the…

Q: Q 3 A square steel bar 50 mm on a side and 1 m long is subject to an axial tensile force of 250 kN.…

Q: A 10.0 m long with a cross sectional area 180 mm? copper rod carries a tensile load of 5 kN at 30°C.…

A: Given Data L=10 m=104 mm A=180 mm2 P=5 kN T=30°C To=20°C E=117 GPa a=17*10-6

Q: A solid circular rod with a a circular groove (r = 1.5 mm) and diameter D = 18 mm, Q4 is subjected…

A: The value of the diameter (d), is: d=D-2r=18-2(1.5)=15 mm Now use the Poison's ratio (0.32) and…

Q: Three parallel vertical rods of equal length (L-2m) support a rigid beam AB to which a force…

Q: Problem 5: A circular bar of diameter 2.5 cm is subjected to an axial tension of 20 kN. If the…

A: Stress is the resistance offered by the body per unit area and strain is the measure of the…

Q: Problem Rigid bar ABCD is initially horizontal before the load W is applied and a change of…

Q: steel pin-ended struts of various lengths, two of the values obtained were: In an experimental…

A: Given data,d=1.2cm=0.012mE=200 GN/m2when struts are in endedLe=L and I=π64d4=π640.0124=1.017×10-9 m4

Q: In the cage system in Figure 3, circular section steel bars will be used. Calculate the minimum…

A: The free body diagram of the truss is as follows: Calculate the moment about point D as follows:…

Q: A 1 m length bar of square cross section with side length 2cm, . is fully supported at one end and…

Q: A steel bar of 30 mm * 30 mm square cross section is subjected to an axial compressive load of…

A: As per given A=30×30mm Load=300kn We have to determine contraction of bar

Q: Coefficient of expansion αB= 165.10^-7 1/ 0C , solid copper bar diameter 20 mm , It is placed in a…

A: From the given description: From continuity equation,

Q: A steel rod is stretched between two walls. At 20C, the tensile force in the rod is 5000N. If the…

Q: A homogeneous 800 kg bar AC is supported by two cables as shown in Figure Q2. Double shear and…

A: Given: Mass of the homogeneous bar AC, m = 800 kg Length of the bar AC, L = 10 m At A, a double…

Q: A hollow compression member with circular cross section having outer diameter 2 times the inner…

Q: A prismatic bar held between the two supports is heated above ambient by 30°C Elastic Modulus ofthe…

A: Stress: When a component or a part is subjected to any external force, a resisting force will be…

Q: A composite shaft consists of a brass sleeve securely bonded to half steel shaft, fixed at end A as…

Q: A cylindrical assembly consisting of a brasscore and an aluminum collar is compressed by a loadP…

A: (a) Calculate the cross-section area of the aluminum collar from the given figure. A1=π440 mm2-25…

Q: A solid circular rod with a diameter d= 18 mm is shown in Figure Q-3. The rod is made of an aluminum…

A: The diametral strain of the rod can be determined as, The longitudinal strain of the rod can be…

Q: The cantilevered bar in the figure is made from a ductile material and is statically loaded with Fy…

Q: A composite section 2 m in length, consisting of a steel tube with outer diameter 24 m and thickness…

A: Given, Length of the composite section, L =m Outer diameter of steel tube , dso = 24 mm Thickness…

Q: A leaf spring in an automobile is subjected to cyclic stresses. The average stress = 150 Mpa;…

A: Given Data The average stress is: Savg=150 MPa The variable stress is: Sγ=500 MPa Yield point…

Q: A steel rod is stretched between two rigid walls and carries a tensile load of 4,075 N at 20°C. If…

A: Now write the net elongation in the rod due to mechanical load and thermal load.

Q: A bronze bar 3 m long with a cross sectional area of 320 mm 2 is placed between two rigid walls. At…

A: Given: Length of bar, L = 3m Area of cross-section; A = 320mm2 Initial temp.; T =20oC Compressive…

Q: A composite bar BCD has a uniform external radius R. = 10 cm. Segment BC is solid steel, w composed…

Q: -20kN 8. A steel bar ABCD 4 m long is subjected to force as shown in figure below. Find the…

A: Answer: The total elongation of the bar is 1.7507 mm.

Q: A copper column of annular cross section has an outer diameter of 5m and is subjected to an axial…

A: Given Outer diameter of column do=5 m Axial load applied P=200 kN Allowable compressive stress…

Q: PProb. 2.8-10. A load W is to be suspended from a cable at end C of a rigid beam AC, whose length is…

A: Given Data The stress acting in the y axis for the rod BD is: σy=250 MPa The modulus of elasticity…

Q: Uniform AB brass rod has a rectangular vertical cross section, fixed with support and pin as shown…

A: GivenL=7mP=1.8Kn =1800Nd=60mm=0.06mE=150Gpa =150×109Pa

Q: Q / The mechanism shown in the figure below has 0.02 in. gap at 80 Fahrenheit degree, find (a) the…

Q: Shown below is a rigid beam ABC that is connected by pinned connections to rod (1) at A, rod (2) at…

A: Given Data: The length of rod 1 is l1= 250 mm. The length of rod 2 is l2 =500 mm. The diameter of…

Concept explainers

Mechanisms of heat transfer

Heat transfer is an essential discipline in thermal engineering that deals with the transfer, conversion, usability, and creation of heat or thermal energy. Transfer of heat occurs through various mechanisms like conduction, convection, radiation, and change of phases. All these mechanisms have distinct characteristics, but these mechanisms can simultaneously occur in an identical system.

Question

ASAP please

A forged steel link with uniform diameter of
30mm at the centre is subjected to an axial
force that varies from 40kN in compression to
160 kN endurance strength of the steel material
are 600MPA,420 MPa and 240MPA
respectively. Find FOS against fatigue
endurance as per Soderberg's criterion.

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Step by step

Solved in 2 steps

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.

Similar questions

oblem 100 A bar of steel has the minimum properties S₂ = 40 kpsi, Sy = 60 kpsi, and Sut = 80 kpsi. The bar is subjected to a steady torsional stress of 15 kpsi with an alternating torsional component of 15 kpsi and an alternating bending stress of 12 kpsi. Find the factor of safety guarding against a static failure, and either the factor of safety guarding against a fatigue failure or the expected life of the part. For the fatigue analysis use: Goodman criterion.
ou A bar of steel has the minimum properties S,- 276 MPa, S,-413 MPa, and Su= 551 MPa. The bar is subjected to a steady torsional stress (r m) of 103 MPa and an alternating bending stress (oa ) of 172 MPa. Find the factor of safety guarding against a static failure, and either the factor of safety guarding against a fatigue failure or the expected life of the part. For the fatigue analysis use: (a) Modified Goodman criterion. (b) Gerber criterion. (c) ASME-elliptic criterion note // assume the Kr and Ks equal 1
What is the difference between static and dynamic loading.. Explain with the drawing the types of dynamic loading. b) In the figure shown, a column of AIAL 1045, cold drawn, rotates on bearings. A force of SKN is applied to it8kn . Find the modified resilience limit stress, the stress of Al-Tin Amra
A leaf spring in an automobile is subjected to cyclic stresses. The average stress = 150 Mpa; variable stress = 500 MPa; yield point stress = 350 MPa and endurance limit = 150 MPa. Estimate, under what factor of safety the spring is working, by Goodman and Soberberg formulate
A hollow compression member with circular cross section having outer diameter 2 times the inner diameter and ultimate tensile strength 650 MPa is subjected to an axial load of 50KN and F.S of 5. Find the inner diameter.
Q3\ The cantilevered bar shown in the fig. made from steel Cold-drawn with (Sy = 280 MPa) and is loaded by the forces F=0.55 kN, P 8 kN, and T 30)N m, Preiciple %3D stress in z axis is -20Mpa. Compute the factor of safety, based upon the distortion-energy theory, for stress elements at A.
A hollow circular shaft of inner radius 10 mm outer radius 20 mm and length 1 m is to be used as a torsional spring. If the shear modulus of the material of the shaft is 150 GPa, the torsional stiffness of the shaft (in kN-m/rad) is?
A 200 GPa young's modulus of a piston rod of diameter 20 mm and length 700 mm in a hydraulic cylinder is subjected to a compressive force of 10 kN due to the internal pressure. The end conditions of rod may be assumed as guided at the piston end and hinged at the other end.Calculate the factor of safety for the piston rod.
A brittle material made of ASTM grade 30 cast iron has ultimate strength in tension of 31 kpsi and ultimate strength in compression of 109 kpsi and undergoes the following plane of stress state: o, = 20 kpsi and Tyy = 10 kpsi (CW). a) using the 3D Mohr's circle, find all three principal normal stresses. b) using the Brittle-Coulomb-Mohr theory and Modified-Mohr theory, find the factors of safety for the given plane of stress state.
PROBLEM 2A tri metallic bar is uniformly compressed by an axial force P=12kN applied through a rigid end plate. The bar consists of a circular steel core surrounded by brass and copper tubes. The steel core has a diameter 10mm, the brass tube has an oute diameter of 15mm and the copper tube has an outer diameter of 20mm. E for steel =210Gpa, E for brass =100GPa and E for copper is 120GPa. Calculate the compressive stress of each metal due to force P.
Quesron L UESTION from beading Support Diperenticte nomal caial looding your answer with neat explanatory sketches that show the possible tyes f type of loading de formation resulting from each
5 A one mm diameter steel wire is wounded around a copper tube with external and internal diameters of 140 mm and 120 mm respectively, to increase the strength of tube against internal pressure, find what initial tension must be given to wire, so that maximum allowable stresses for the tube and wire materials 90 and 200 N/mm? respectively are reached simultaneously. Assume poisson coefficient for wire and tube material as 0.3. Modulus of elasticity for copper and steel wire 1000 N/mm' and 2000 N/mm? respectively. The tube is open at ends. reouirements