A gas with density 1.3kg/m and dynamic viscosity 4air = 1.1 x 10-5Pa. s flows past a flat plate of length L=2.2m and width B =1.2m. The shear force on one side of the plate is Fs = 1N. Assuming that the flow is turbulent from the leading edge of the plate, what is the velocity of the gas past the plate? The velocity is V = m/s. (Provide your answer to 2 decimal places.)

A gas with density 1.3kg/m and dynamic viscosity 4air = 1.1 x 10-5Pa. s flows past a flat plate of length L=2.2m and width B =1.2m. The shear force on one side of the plate is Fs = 1N. Assuming that the flow is turbulent from the leading edge of the plate, what is the velocity of the gas past the plate? The velocity is V = m/s. (Provide your answer to 2 decimal places.)

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

A viscous fluid of viscosity 2.48 Pa-s and density 884 kg/m³ is dragged by a rigid flat surface that moves upward with speed V, as shown. The velocity profile in the fluid layer is of the form, pg v(x) = (x? – 2hx) + V Find the minimum speed V for which the entire fluid layer moves upward. What are the minimum and maximum values of the shear stress in the layer? Assume the flow to be incompressible and fully developed. 5 mm
An incompressible fluid (kinematic viscosity, 7.4 x10-7 m²/s, specific gravity, 0.88) is held between two parallel plates. If the top plate is moved with a velocity of 0.5 m/s while the bottom one is held stationary, the fluid attains a linear velocity profile in the gap of 0.5 mm between these plates; the shear stress in Pascals on the surface of top plate is (a) 0.651 x 10-3 (c) 6.51 (b) 0.651 (d) 0.651 x 103
A fluid with specific weight of 12000 N/m³ and viscosity of 0.002 kg/m.s flows between two parallel plates as shown in the figure. The upper plate moves with the velocity of U and the lower plate is fixed. (a) Find the velocity profile u(y) in terms of h, U, and dp/dx. Assume the flow is steady, 2D, and parallel to the plates. (b) A manometer is used to measure the pressure drop Ap = p2- pi of the flow. Find Ap if the elevation difference in the manometer is H=0.2 cm and ym=16000 N/m³. (c) Assuming dp/dx Ap/L, find the fluid velocity at y=h/2. Consider h=2.5 cm, L=15 cm, and U=0.007 m/s.
An incompressible fluid (kinematic viscosity, 7.4 x10-7 m²/s, specific gravity, 0.88) is held between two parallel plates. If the top plate is moved with a velocity of 0.5 m/s while the bottom one is held stationary, the fluid attains a linear velocity profile in the gap of 0.5 mm between these plates; the shear stress in Pascals on the surface of top plate is rt of this book may be repro
[1] A Newtonian fluid with a viscosity u and density p, is flowing at a laminar condition on an inclined plate with the length Land width W at a temperature T as shown in the figure. The fluid layer on the plate has a thickness of d. Establish the mass, energy, and momentum balances based on the given system. Draw the velocity and shear stress profiles. H, P AP Øm2
An incompressible fluid (kinematic viscosity =7.4x10-7 m2/s, specific gravity=0.88) is held between two parallel plates. If the top plate is moved with a velocity of 0.5 m/s while the bottom one is held stationary the fluid attains a linear velocity profile in the gap of 0.5 mm between these plates,find the shear stress in Pascal on the surface of top plate.
A cylindrical machine part moves within a surrounding cylinder. The centrelines of the part and the surrounding cylinder are coincident. The cylinder is full of an oil (viscosity 0.25kg/ms) that is not flowing i.e. no pressure gradient is applied. What is the value of the viscous force exerted on the machine part as it moves along the cylinder at a speed of 9m/s? • The machine part is 0.06m long and has a radius of 0.041m. • The ratio of the machine part radius to the cylinder radius is 0.98. • Assume that the flow is dominated by viscous forces. • Give your answer as an absolute value i.e. no negative sign, in Newtons to one decimal place.
The wing of a tactical support aircraft is approximately rectangular with a wingspan (the length perpendicular to the flow direction) of 16.5 m and a chord (the length parallel to the flow direction) of 2.75 m. The airplane is flying at standard sea level with a velocity of 250 ms¯¹. Assume the wing is approximated by a flat plate. Assume incompressible flow. Use μ = 1.789 x 10-5 kg/ms (a) If the flow is considered to be completely laminar, calculate the boundary layer thickness at the trailing edge and the total skin friction drag.
The block of weight W = 50 N is pulled by a weight W0 = 60 N along the surface of a table by means of an inextensible cable and a pulley. Between the block and the table there is a uniform layer of oil of viscosity m = 0.1 Pa-s and clearance h = 2 mm. The contact area is 0.01 m2. Find the terminal velocity U if the table is very long.
(a) A wing section with a chord of c and a span of b is mounted at zero angle of attack in a wind tunnel. A pitot probe is used to measure the velocity profile in the viscous region downstream of the wing section as shown in the figure. The measured velocity profile is u(z) = U∞ - (U/2) cos[TZ/(2w)] for -w ≤ z ≤w. Here, w = 0.02c. Assuming a constant pressure p = Poo along the streamlines (dashed lines in the figure) and across the wake where the velocity was measured, calculate the friction drag coefficient Cp, of the wing section. Upo ZA Streamlines u = U-L co COS +w Viscous wake 'W 2w
(a) A wing section with a chord of c and a span of b is mounted at zero angle of attack in a wind tunnel. A pitot probe is used to measure the velocity profile in the viscous region downstream of the wing section as shown in the figure. The measured velocity profile is u(z) = U∞ - (U/2) cos[TZ/(2w)] for -w ≤ z ≤w. Here, w = 0.02c. Assuming a constant pressure p = po along the streamlines (dashed lines in the figure) and across the wake where the velocity was measured, calculate the friction drag coefficient Cp, of the wing section. U Streamlines u = U_ -- cos 22 2W² +w Viscous wake = -W (b) Consider a thin flat plate at zero angle of attack in an airflow at P∞ = 1.225 kg/m³, T∞ = 288 K and μ∞ 1.7894 x 10-5 kg/m/s. The length of the plate is 2 m and the span is 0.5 m. Assume the boundary layers on the plate are laminar throughout (on the upper and lower surfaces both) where LBL(x)/x = 0.664/√√/Rex applies. The freestream velocity is 100 m/s. Calculate the friction drag (Df) of the first…
Oil flows between two very long parallel plates, separated from H, with width b. The bottom plate moves with speed U and is isolated. The upper plate is at rest and receives heat from the environment at a rate equal to qs". Consider laminar flow, thermally developed. Due to the high viscosity of the fluid, viscous dissipation is relevant U isolada 1 - Estimate the velocity profile considering the null pressure gradient and determine the average speed. 2. Determine dissipation per volume unit. 3. Set mixing temperature and determine the mixing temperature variation over the plates.