A helical compression spring is fabricated from ASTM A229 oil-tempered wire (Figure 14.3a) and has the mean coil diameter D = 10 mm, wire diameter d = 0.9 mm, total number of active coils N₂ = 14.5, and the modulus of rigidity G = 79 GPa. Find a. The torsional yield strength of the wire

A helical compression spring is fabricated from ASTM A229 oil-tempered wire (Figure 14.3a) and has the mean coil diameter D = 10 mm, wire diameter d = 0.9 mm, total number of active coils N₂ = 14.5, and the modulus of rigidity G = 79 GPa. Find a. The torsional yield strength of the wire

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

A helical compression spring is wound using 0.12-in-diameter phosphor-bronze B159 wire. The spring index C = 10 and the total number of coils is N = 14. You may assume that the spring has both ends squared and ground and is supported between fixed ends. Also, Sgy = 0.45 · Sut- a. Estimate the spring rate. b. Estimate the static load corresponding to the yield strength. c. What should the free length of the spring be to ensure that when it is compressed solid the torsional stress does not exceed the yield strength? d. Calculate the critical value of the free length of the spring to avoid buckling.
The spring constant of a helical compression spring DOES NOT depend on (A) coil diameter (B) material strength (C) number of active turns (D) wire diameter
5. Design a helical compression spring for a maximum load of 1000 N and deflection of 25mm taking Wahl’s factor into consideration. Assume spring index as 5, maximum permissible shear stress for spring wire as 420 MPa and modulus of rigidity as 84 kN/mm2
6. It is desired to design a valve spring of I.C. engine for the following details: (a) Spring load when valve is closed 80 N (b) Spring load when valve is open = 100 N (c) Space constraints for the fitment of spring are : Inside guide bush diameter = 24 mm Outside recess diameter= 36 mm (d) Valve lift 5 mm (e) Spring stcel has the following properties: Maximum permissible shear stress = 350 MPa Modulus of rigidity 84 kN/mm? ried: 1 Wire diameter; 2. Spring index; 3. Total number of coils; 4. Solid length of sprine: 5. Free
A helical compression spring is made with oil-tempered wire of diameter 0.2", mean coil diameter of 2", 12 total coils, 5" free length, and squared ends. (a) Find the solid length. (b) Find the force required to compress the spring to closure? (c) Find the factor of safety against yield when compressed to the solid length. (Hint: Uses Say= 0.5 Sut for shear strength.)
1. Design a compression helical spring to carry a load of 500 N with a deflection of 25 mm. The spring index may be taken as 8. Assume the following values for the spring material: Permissible shear stress = 350 MPa Modulus of rigidity = 84 kN/mm2 4С - 1 0.615 Wahl's factor where C-spring index. 4С - 4
2. A helical valve spring is to be designed for an operating load range of approximately 90 to 135 N. The deflection of the spring for the load range is 7.5 mm. Assume a spring index of 10. Permissible shear stress for the material of the spring 480 MPa and its modulus of rigidity 80 kN/mm. Design the spring. %23 4C - 1 0.615 Take Wahl's factor C being the spring index. 4C - 4 |Ans. d-2.74 mm; D 27.4 mm; n 6|
1. Design a helical spring for a spring loaded safety valve for the following conditions: Operating pressure Maximum pressure when the valve blows off freely = 1 N/mm? = 1.075 N/mm2 Maximum lift of the valve when the pressure is 1.075 N/mm2 = 6 mm Diameter of valve seat =100 mm Maximum shear stress 400 MPa %3D Modulus of rigidity = 86 kN/mm? Spring index = 5.5 [Ans. d= 17.2 mm; D=94.6 mm; n=12| A vertical epring loaded ualue ia noonin
Required information A helical compression spring is wound using music wire of diameter, d, 2.16 mm. The spring has an outside diameter, OD, of 27 mm with plain ground ends and 14 coils. NOTE: This is a multi-part question. Once an answer is submitted, you will be unable to return to this part. What should be the free length to ensure that the torsional stress does not exceed the yield strength when the spring is compressed solid? What is the critical free length? Is there a possibility that the spring might buckle in service? The free length should be |mm. The critical free length should be Buckling is likely Eto occur. mm.
6. It is desired to design a valve spring of I.C. engine for the following details : (a) Spring load when valve is closed = 80 N (b) Spring load when valve is open = 100 N (c) Space constraints for the fitment of spring are : Inside guide bush diameter = 24 mm Outside recess diameter = 36 mm (d) Valve lift = 5 mm (e) Spring steel has the following properties: Maximum permissible shear stress = 350 MPa Modulus of rigidity = 84 kN/mm? Find : 1. Wire diameter; 2. Spring index; 3. Total number of coils; 4. Solid length of spring; 5. Free Тop
Design a helical spring to be used in spring balance with a wire diameter of 6mm and the outside diameter should be limited to 66mm. if the permissible shear stress of the spring material is 325 N/mm? and the Modulus of rigidity is 85kN/mm?. a) Compute the deflection of spring per active turn and the axial load on the spring considering the effect of curvature, take Wahl's factor as Kw= 1.1 b) Calculate the value of axial load neglecting the effect of stress factor. **Note: Please upload your handwritten working/solution to the link provided. The value of Mean diameter of the spring in mm . The Spring Index is. Shear stress factor, neglecting curvature effect . Deflection per active turn in mm Axial Load W in N .. Axial Load W in N. considering effect of curvature .
A helical compression spring is 1o exert a force of 8.0 Ib when compressed 1o a length of 1.75 in. At a length of 1.25 in, the force must be 12.0 Ib. The spring will be installed in a machine that cycles slowly. and approximately 200 000 cycles total are expected. The tem- perature will not exceed 200°F. The spring will be installed in a hole having a diameter of 0.75 in. For this application. specify a suitable material, wire diameter. mean diameter. OD. ID. free length, solid length. number of coils, and type of end condition. Check the stress at the maximum operating load and at the solid length condition. The first of two solution procedures will be shown. The numbered steps can be used as a guide for future problems and as a Kind of algorithm for the spreadsheet approach that follows the manual solution.