A homogeneous cylinder is submerged into two layers of liquid composed of water at the top layer and a heavier, non-polar liquid (SG=3.6) at the lower layer. It settled in equilibrium as shown in the figure. Diameter 125mm Draft in H20-710mm Draft in Non-Polar Liquid-280mm a. Determine the density of the cylinder. b. How much vertical force is needed to push the cylinder down by twice the given draft in the non-polar liquid? Use r = 3.14.

A homogeneous cylinder is submerged into two layers of liquid composed of water at the top layer and a heavier, non-polar liquid (SG=3.6) at the lower layer. It settled in equilibrium as shown in the figure. Diameter 125mm Draft in H20-710mm Draft in Non-Polar Liquid-280mm a. Determine the density of the cylinder. b. How much vertical force is needed to push the cylinder down by twice the given draft in the non-polar liquid? Use r = 3.14.

Name: A homogeneous cylinder is submerged into two layers of liquid compose
Uploaded: 2024-03-20T06:56:55.000Z
Channel: Bartleby
Description: A homogeneous cylinder is submerged into two layers of liquid composed of water at the top layer anda heavier, non-polar liquid (SG=3.6) at the lower layer. It settled in equilibrium as shown in the figure.Diameter-125mmDraft in H20-710mmDraft in No

International Edition---engineering Mechanics: Statics, 4th Edition

4th Edition

ISBN:9781305501607

Author:Andrew Pytel And Jaan Kiusalaas

Publisher:Andrew Pytel And Jaan Kiusalaas

Chapter8: Centroids And Distributed Loads

Section: Chapter Questions

Problem 8.121P: One side of the container has a 03-m square door that is hinged at its top edge. If the container is...

See similar textbooks

Similar questions

The hemispherical glass bowl is filled with water. Find the location y of the center of gravity of the filled bowl. Approximate the bowl as a thin shell of radius R=6.15in. Use 1=162lb/ft3 for glass and 2=62.4lb/ft3 for water.
One side of the container has a 03-m square door that is hinged at its top edge. If the container is filled with water, determine the smallest force F that must be applied to the bottom edge of the door to keep it closed.
A glass tube of intemal diameter 3 mm is immersed in mercury. The angle of contact of mercury with glass can be taken as 130°. What will be the level of Hg in the tube relative to the free surface of the liquid outside the tube? Take surface tension of liquid 0.48 N/m.
Question: A shaped pipe having an inner diameter of 76 mm is mounted to an open atmosphere tank as shown in the figure given below. Tank is filled with water. Shaped pipe is filled with an unknown liquid. Equilibrium is reached as shown in the figure. Calculate the density of the unknown liquid in terms of ton/m³. Givens: Pwater=1 g/cm³; pair=0,0013 g/cm³; g=9.81 m/s²; ywater=9810 N/m³. h/2 h -Air Water h/2 45 h/2 Unknown Liquid 2h
A rectangular aluminium block with a cavity at its center is completely submerged in water as shown in Figure 2.3. The dimensions of the block are 10 cm x 8 cm x 6 cm. The densities of aluminum and water are 2700 kg m-3 and 1000 kg m-3 respectively. The mass of air in the cavity can be neglected. The block is able to stay at rest uprightly in water as shown in Figure 2.3. Draw and label the force(s) acting on the aluminium block in Figure 2.3 Deduce the weight of the aluminium block using the pressure difference found in (b)(i) which is given by ρg(h2 – h1). . Hence, find the volume of the cavity.
Consider the hemispherical gate attached to a cylindrical buoy as shown in the figure. The thickness of and weight of the cable connecting the buoy and the gate are negligible. Which of the following is the volume above the hemispherical gate that is needed in the calculation of the vertical component of the resultant hydrostatic force acting on it? 4m Y? 3 m Select one: O a. cylinder up to the liquid surface O b. cylinder up to the liquid surface minus the hemisphere O c. cylinder up to the bottom surface of the buoy O d. cylinder up to the bottom surface of the buoy minus the hemisphere
2. A circular ring (radius = 5.0 cm) is used to determine the surface tension of a liquid. The plane of the ring is positioned so that it is parallel to the surface of the liquid. The ring is immersed in the liquid and then pulled upward, so a film is formed between the ring and the liquid. In addition to the ring's weight, an upward force of 3.6 x 10 N is required to lift the ring to the point where it just breaks free of the surface. What is the surface tension of the liquid?
A closed tank whose bottom is 18 inches in diameter is filled with three liquids: 4 inches of carbon tetrachloride (SG=1.59), 2 inches of water and 12 inches of syrup (SG=1.31). The air chamber in the tank is pressurized at 1296 psf. d. Apply the PANEL EQUATIONS to determine the magnitude, direction and location of the total hydrostatic force acting at the bottom of the tank.
The fresh-water side of a concrete dam has the shape of a vertical parabola with a vertex at A. Let d represent the dam's depth (into the figure's plane). The value of d is unknown, and you may express it as d in your analysis. Determine (a) The horizontal and vertical components of the pressure force acting on the dam and their respective lines of action location. (b) The line of action of the reaction force exerted by the dam passes through point B. Calculate the distance b. Useful information: p = g=9.81m2, x= ³a, y = 3, A = 2ab 3a 10³ kg 36 m -27 m C Parabolic Area a b m³,
Problem 1 AU-shaped tube is partially filled with a liquid of known density p1. At the right end, another liquid of unknown density p2 is added. These are immiscible, and the heights of the columns are hi and h2, respectively, as shown in the figure below. Determine the density p2. d.1. h2 hi p2 P1
A glass tube of internal diameter 3mm is immersed in mercury. The angle of contact of mercury with glass can be taken as 130°. What will be the level of Hg in the tube relative to the free surface of the liquid outside the tube? Take surface tension of liquid = 0.48 N/m.
A gate with a mass of 45 kg is hinged at point A. The gate dimensions are a = 90 cm and b = 60 cm, and the angle between the horizontal is 45°. A counterweight of W is attached with a rod to balance the gate, as shown in the figure. If the length of the balancing rod is 90 cm and the vertical distance from point A to the free surface of the water is given as 30 cm, determine the required mass of counterweight to keep the gate closed.