A horizontal cantilever 2 m long is constructed from z-section shown in Fig. 9.19. A load of 10 kN is applied to the can- tilever at an angle of 60° to the horizontal as shown. Assuming that no twisting moment is applied to the section, determine the stresses at points A and B. Ix = 48.3 × 10-6 m², I₂ = 4.4 × 106 m², Ixy = 9.91 × 106 m². What will be the deflection of the end of the cantilever ? y E = 200 GN/m². 80 + 18 U 240 x- 60° 10kN B ТУ 18 Ꮎ H 80 All dimensions in mm Fig. 9.19 주

A horizontal cantilever 2 m long is constructed from z-section shown in Fig. 9.19. A load of 10 kN is applied to the can- tilever at an angle of 60° to the horizontal as shown. Assuming that no twisting moment is applied to the section, determine the stresses at points A and B. Ix = 48.3 × 10-6 m², I₂ = 4.4 × 106 m², Ixy = 9.91 × 106 m². What will be the deflection of the end of the cantilever ? y E = 200 GN/m². 80 + 18 U 240 x- 60° 10kN B ТУ 18 Ꮎ H 80 All dimensions in mm Fig. 9.19 주

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

1. Two cables A and B had their both ends attached to each other as shown. Cable A is 10 in long and cable B is 0.5 in longer than cable A; hence making cable B slack. The diameter of cable A is 0.70 in. while cable B has a diameter of 0.25 in. Find the stresses for both cables if the system supports a downward force P = 0.15kip. Use E = 50ksi. P
Calculate the smallest area of each cable if the stress is not to exceed 76 000 KPa in bronze and 118 MPa in steel if a homogeneous 778 000 g bar AB is supported at either end by a cable.
1. A 60-mm diameter steel tube with a wall thickness of 3 mm just fits in a rigid hole. Determine the tangential stress developed if an axial compressive load of 12 kN is applied. Use v = 0.30 and E = 200 GPa. Answer: 0 = 6.37 MPa 2. A 200-mm long bronze tube closed at both ends fits without clearance in a 70-mm hole in a rigid block. It has a diameter of 70 mm and a wall thickness of 5 mm. The tube then sustained an internal pressure of 4.5 MPa. Use v = 0.33 and E= 83 GPa. Compute the tangential stress in the tube. Answer: Ot = 5.20 MPa
Eight steel cables (with equal distance to each other) are supporting a circular heavy moulding of diameter 3m from an overhead point. If the moulding weighs 5 kN/m and the attachment point is 4m above it, determine the following:a. Calculate the tension of the cable.b. Determine the diameter of the wire if the allowable stress is 125 MPa.c. If the diameter of the cable is 10 mm, find the deflection of the steel cable.d. If the diameter of the cable is 10 mm, find the vertical displacement of the molder.
The P load applied to a steel bar is transferred to the board by an annular washer. The diameter of the rod is 34mm and the inner diameter of the washer is 35.7 mm. Since it is known that the axial normal stress on the steel bar is 119 MPa, and the average bearing stress between the washer and the board should not exceed 34 MPA, how many mm is the smallest allowable outer diameter of the washer?
Three cables having an area of 0.05 in^2 each is carrying the load W as shown. With no stress, the original lengths of the cables are 74.99 ft, 75.00 ft, and 74.94 ft. E = 29 x 10° psi Calculate for the stress in the intermediate wire. Choices: a. 8,026.65 psi b. 9,999.66 psi c. 19,939.80 psi d. 10,102.52 psi 1500 lb
Q6 A spherical vessel of 1.6m inner diameter is constructed by joining two hemispheres with equally spaced bolts as shown in fig.3. The vessel will operate at an internal pressure of 600kPa. Calculate the vessel plate thickness t. Given the allowable stress for the sphere plate will equal 50MPa. If the same plate was used to make a cylindrical vessel to operate at the same internal pressure, find the cylinder maximum allowable diameter. ... المزيد A Ľ تعديل حذف 0 المفضلة Lo مشاركة
1. A BRONZE ROD IS SUBJECTED TO A TENSILE LOAD OF 15,000N. IF ITS ALLOWABLE STRESS IS 75 MPa, CALCULATE THE OUTER LENGTH OF THE SIDE OF THE PENTAGONAL TUBE IF THE INNER LENGTH OF THE ONE SIDE IS 40mm. 15,000N 15,000N 40mm CROSS-SECTION OF THE BRONZE ROD BRONZE ROD
The rectangular bar shown is connected to a support bracket with a 24 mm diameter pin. The width of the rectangular bar is 70 mm and its thickness is 15 mm. The bearing stress in the bar cannot exceed 120 MPa. Determine the maximum value of Pmax that can be supported based solely on consideration of the bearing stress in the bar. Note: This question is not asking about any stresses in the support bracket...just bearing stress in the rectangular bar.
An engineering machine component operating in a high temperature environment consists of a copper pipe having a cross-sectional area of 2 000 mm² and 0.3 m long, which is placed between two rigid caps. Four M22 steel bolts are symmetrically arranged around the tube and parallel to the axis of the tube and are lightly tightened. 3.1 Find the stress in the pipe and the bolts if the temperature of the assembly is increased from 25 °C to 95 °C. 3.2 What load will each bolt carry at the raised temperature? 3.3 Make a neat sketch of the assembly. (Est = 200 GPa, Ecu – 100 GPa, as: = 12 × 10-6/ °C, acu = 16 × 10-6/ °C)
Please don't copy from other sources.will report The section of a crane hook is rectangular in shape whose width is 30 mm and depth is 60 mm. The centre of curvature of the section is at a distance of 125 mm from the inside section and the load line is 100 mm from the same point. Find the capacity of the hook, if the allowable stress in tension is 75 MPa. Also determine the location of the neutral axis and the stress at inner and outer fiber.
A simple pin connected truss is loaded and supported as shown. The truss is constructed from three aluminum members, each having a cross sectional area of A = 1220 mm ^2. Assume a = 1.4 m, b = 8.9 m, and c = 3.6m. If P = 60kN and Q = 80kN determine the normal stress in each member.