A laterally supported, compact beam is simply supportéd át Böth ends. It is subjected to loads that would bend the section's major x-axis. Given: Plastic Modulus, Zx = 4.10 x 10^6 m^3 Plastic Modulus, Zy = 1.00 x 10^6 mm^3 Yield Strength, Fy 350 MPa Resistance Factor for Flexure, phi = 0.90 Evaluate the design capacity of the beam, in kN-m. 1435 1201 1291 1538

A laterally supported, compact beam is simply supportéd át Böth ends. It is subjected to loads that would bend the section's major x-axis. Given: Plastic Modulus, Zx = 4.10 x 10^6 m^3 Plastic Modulus, Zy = 1.00 x 10^6 mm^3 Yield Strength, Fy 350 MPa Resistance Factor for Flexure, phi = 0.90 Evaluate the design capacity of the beam, in kN-m. 1435 1201 1291 1538

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

The members of the truss are 25mmx50mm in cross section. Determine the maximum load P that can be applied so that the stresses will not exceed 100 MPa in tension or 70 MPa in compression. See figure 101. Choose the best answer. Figure 101 2m 1.5m 2.5m
The following steel circular bar (Es = 200 GPa) is divided into two segments. Segment 1 is tubular and segment 2 is solid. Determine the distance "x" so that the bar does not exceed a total deformation of 2.5 mm. The load P is equal to 25 kN, the diameter d is equal to 30 mm, and the length L is equal to 10 m.
Asiacell|Asiacel K/s Asiacell For simply supported beam with rectangular cross section shown, determine the values and location of the maximum tensile and compressive bending * stresses 1000 lb 400 lb/ft 6 in DV 8 in 10 ft RA Rp
An 8 m long steel is simply supported at the left end and 2 m from the right end. It carries a total uniform load of 45 kN/m all throughout its length. STEEL DECION CIVIL ENGINEERING Beam properties: A = 11,500 mm² bf = 250 mm tw = 10 mm d == 350 mm If=: 16 mm lx = 266 x 10 mm If the Beam is laterally supported throughout the beam a) Determine the Maximum Bending Stress b) Determine the Maximum Web Shear Stress c) To strengthen the beam, 2-200 mm x 10 mm cover plates, one at the top of the flange and the other at the bottom of the flange were added. What is the resulting maximum bending stress?
A steel structural member is to be used as a column 5 m long. The column is to be pinned at both ends for bending about X-X axis and fixed at one end and pinned at the other for bending about Y-Y axis. The properties of the member section are as follows:E= 200 GPa, yield stress= 350 MPa, Ixx = 222 x 106 mm4, Iyy = 72.71x106 mm4 and A= 12.33 x 103 mm2Using Perry-Roberston equation, calculate the buckling stress and the corresponding load
An 8 m long steel is simply supported at the left end and 2 m from the right end. It carries a total uniform load of 45 kN/m all throughout its length. STEEL DECION CIVIL ENGINEERING Beam properties: A= 11,500 mm² bf = 250 mm tw- 10 mm d = 350 mm If=: 16 mm lx = 266 x 100 mm If the Beam is laterally supported throughout the beam b) Determine the Maximum Web Shear Stress
1 A rectangular beam has the dimensions (see Fig. 3.2b) b = 250 mm, h = 650 mm, and d = 600 mm and is reinforced with three No. 25 (No. 8) bars so that A, cylinder strength f is 28 MPa, and the tensile strength in bending (modulus of rupture) is 3.27 MPa. The yield point of the steel f is 420 MPa, the stress-strain curves of the materials being those of Fig. 1.16. Determine the stresses caused by a bending moment M 1530 mm. The concrete 61KN-m.
Q4: The aluminum block has a rectangular cross section and is subjected to an axial compressive force of 8 kip. If the 1.5-in. side changed its length to 1.500132 in., determine the Poisson's ratio. Assume modulus of elasticity (E) = 10 x 10^3 ksi 1.5 in.j 2 in. 8 kip- 8 kip 3 in.-
A small aluminum alloy [E = 65 GPa] tee shape is used as a simply supported beam as shown. For this beam, a = 125 mm. The cross-sectional dimensions of the tee shape are b= 15 mm, d = 23 mm, and t = 9 mm. After loads are applied to the beam at B, C, and D, a compressive normal strain of 460 u is measured from a strain gage located at c = 9 mm below the topmost edge of the tee stem at section 1-1. What is the applied load p?
Determine the axial compressive strength of an HSS steel with a length of 4.6m with respect to the principal axis. Use Fy = 318 MPa. Section Properties: A = 1742 mm2 ly = 3.29 x 106 mm4 lx = 9.53 x 106 mm4 CIVIL ENGINEERING. STEEL DESIGN 203.2 -3.2 101.6 -3.2
A small aluminum alloy [E = 73 GPa] teeshape is used as a simply supported beam as shown. For this beam, a = 150 mm. The cross- sectional dimensions of the teeshape are b = 25 mm, d= 38 mm, and t=7 mm. After loads are applied to the beam at B, C, and D, a compressive normal strain of 490cis measured from a strain gage located at c= 9 rmm below the topmost edge of the tee stem at section 1-1. What is the applied load P? 3P Strain gage d a a H Answer: P = i
The stiffness matrix of the beam shown below is - 1. (2 В El 2EI 4m 8m A.