A Long-shunt dynamo running at 800 r.p.m suppLies8 20hw at e a terminal voltage of 200 V. The resistancesof the armature, shunt ficld and senes freld are o-05,lo0, and o.07n vespectively. The overall efficiemey atthe above Load is 85.find cas Cu losses (b) dolRe tronand friction Losses ce) the torque excrted by the primemoter,

In this question we have given long shunt dc generator ...We have to find out losses in generator…

- A Long-shunt dymamo running ad g00 r.p.m suppLies 8 20hw at e a terminal voltage of 200V. The resistances of the armature, shunt ficld and senes freld are o-05, lo0, and o.07A vespectively.the overall efficiemey at the above Load is 8.find cas culosses (b) iAak iron and Friction Losses ce) the torque exerted by the prime motor.

- A Long-shunt dymamo running ad g00 r.p.m suppLies 8 20hw at e a terminal voltage of 200V. The resistances of the armature, shunt ficld and senes freld are o-05, lo0, and o.07A vespectively.the overall efficiemey at the above Load is 8.find cas culosses (b) iAak iron and Friction Losses ce) the torque exerted by the prime motor.

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

A single phase full wave AC voltage controller has a resistive load of 5 ohms and an input voltage of Vs = 220 V (RMS), 50 Hz. The delay angles of both thyristors are set to 90 degrees. The maximum power that can be delivered to the load is: Select one: a. 5.65 kW b. 9.68 kW c. 11.52 kW d. None of these
Maz a) A sinewave is having a frequency of 50 Hz and instantaneous value of 250 Volts at 1.3 milli seconds. Find D The maximum value of sinusoidal voltage waveform and i) The value of voltage at 2.1 milli seconds. b) Determine the instantaneous equation for the voltage waveform shown in figure, if Vp=100 Volts, Time period is 10 milli seconds and 0 =40 degrees. on Vp Upload your Answers steps in the "Final Answer Submission" Link provided in the Moodle. a) (i) Maximnum value = a) (ii) Value of voltage at 2.1 ms = b) Angular frequency =
a) A sinewave is having a frequency of 100 Hz and instantaneous value of 150 Volts at 1.4 milli seconds. Find i) The maximum value of sinusoidal voltage waveform and ii) The value of voltage at 1.7 milli seconds. b) Determine the instantaneous equation for the voltage waveform shown in figure, if Vp=200 Volts, Time period is 5 milli seconds and 0 =40 degrees. Vp t = 0 Upload your Answers steps in the "Final Answer Submission" Link provided in the Moodle. a) (i) Maximum value = a) (ii) Value of voltage at 1.7 ms = b) Angular frequency =
7. A coil having a resistance of 20 ohms and an inductance of 0.75 henry is connected in series with a 30-ohm resistor and to a 120-volt d-c source. A switch across the series resistor is then closed, and the circuit is assumed to be in a steady-state condition. At the instant the switch is opened, what will be the rate of current change and the power delivered by the magnetic field.
Steam enters an adiabatic turbine at 6 MPa and 550 °C and leaves at 10 kPa and 50 °C. If the environment temperature and pressure is 0 °C and 103.325, what is the second law efficiency of the turbine? O a. 0.70 O b. 0.75 O c. 0.81 O d. 0.72 O e. 0.78
• Q5/ in a DC motor. List and describe the types of losses that occur
The induced voltage in dc motors beyond the pole edges is Select one: O a infinity b. 180 V C. 220 V O d. zero
Electrical machine having 5 pole-pairs is supplied with 20 Hz. Peak value of induced back-emf is 120 V. Let's assume there is (0°) zero degrees between rotor and stator and at this moment peak back-emf is induced. What will be mechanical angle between rotor and stator in 0.03 seconds from that moment? What will be an induced back-emf in 0.03 seconds? Angle between rotor and stator deg
a) A sinewave is having a frequency of 50 Hz and instantaneous value of 150 Volts at 1.2 milli seconds. Find i) The maximum value of sinusoidal voltage waveform and i) The value of voltage at 1.7 milli seconds. b) Determine the instantaneous equation for the voltage waveform shown in figure, if Vp=100 Volts, Time period is 5 milli seconds and 0 =50 degrees. Vp i= 0 Upload your Answers steps in the "Final Answer Submission" Link provided in the Moodle. a) (i) Maximum value = a) (ii) Value of voltage at 1.7 ms b) Angular frequency %3D
The resistance of the field winding(copper wire) of a DC machine is 0.25 ohm at 25°C. When operating at full-load, the temperature of the winding is 75 °C. The temperature coefficient of resistance of copper is 0.00427 per °C at 0°C. Find the resistance of the field winding at full-load.
a) A sinewave is having a frequency of 50 Hz and instantaneous value of 100 Volts at 1.3 milli seconds. Find i) The maximum value of sinusoidal voltage waveform and i) The value of voltage at 2.1 milli seconds. b) Determine the instantaneous equation for the voltage waveform shown in figure, if Vp=100 Volts, Time period is 5 milli seconds and o =50 degrees. Vp Ф
The maximum speed of an alternator working at 60 Hz is possible when the number of poles of the machine is ........ a. 4 b. 5 c. 3 d. 2