A long, solid cylinder of radius 2 cm hinged at point A is used as an automatic gate, as shown in Fig. 6. When the water level reaches 15 cm, the cylindrical gate opens by turning about the hinge at point A. Determine (a) the hydrostatic force acting on the cylinder and its line of action when the gate opens and (b) the weight of the cylinder per cm length of the cylinder. Fig. 6

A long, solid cylinder of radius 2 cm hinged at point A is used as an automatic gate, as shown in Fig. 6. When the water level reaches 15 cm, the cylindrical gate opens by turning about the hinge at point A. Determine (a) the hydrostatic force acting on the cylinder and its line of action when the gate opens and (b) the weight of the cylinder per cm length of the cylinder. Fig. 6

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

The storage tank contains lubricating oil of specific weight (y). In one inclined side of the tank, there is a D m diameter circular inspection door, mounted on a horizontal shaft along the centre line of the gate. The oil level in the tank rests h m above the mounted shaft. (Please refer table 01 for relevant y, D and h values) Describe the hydrostatic force and centre of pressure with the aid of a free body diagram of the inspection door. Calculate the magnitude of the hydrostatic force and locate the centre of pressure. Estimate the moment that would have to be applied to the shaft to 450 open the gate. Stop If the oil level raised by 3 m from the current level, calculate the new moment required to open the gate. B specific weight = 7100 D = 0.7 m h = 25 m Figure 01
The storage tank contains lubricating oil of specific weight (y). In one inclined side of the tank, there is a D m diameter circular inspection door, mounted on a horizontal shaft along the centre line of the gate. The oil level in the tank rests h m above the mounted shaft. (Please refer table 01 for relevant y, D and h values) Describe the hydrostatic force and centre of pressure with the aid of a free body diagram of the inspection door. Calculate the magnitude of the hydrostatic force and locate the centre of pressure. Estimate the moment that would have to be applied to the shaft to 450 open the gate. Stop If the oil level raised by 3 m from the current level, calculate the new moment required to open the gate. B specific weight = 7100 D = 0.7 m h = 25 m do last part only Figure 01
• A bin holds three cylinders, each weighing 1200 N. The diameter of each cylinder is 600 mm. Assume frictionless surface. W А В Given: W W= 1200 N ERE C d = 0.6 m Determine: a.) Force at Point A b.) Reaction at Point D RF RG c.) Reaction at Point G ->
A U-tube contains a liquid of relative density 1.25 to a height of 25 cm in both the columns. It is rotated about a symmetrical vertical axis with 15 cm from both the limbs. Calculate the pressure at the bottom end points and mid point when the speed of rotation is 240 revolution per minute. 15cm--15cm- 25 cm IM B
5.32 The four devices shown in Fig. P5.32 rest on frictionless wheels, are restricted to move in the x direction only, and are initially held stationary. The pressure at the inlets and outlets of each is atmospheric, and the flow is incompressible. The con- tents of each device are not known. When released, which de- vices will move to the right and which to the left? Explain. (a) (c) FIGURE P5.32 (b) (d)
3-134 A system is equipped with two pressure gages and a manometer, as shown in Fig. P3-134. For Ah = š cm, deter- mine the pressure difference AP = P, - P. Air Ah Manometer fluid SG = 2.67 Oil SG = 0.87 P1 P2 FIGURE P3–134
A hollow steel tube (1) with an outside diameter of D1 and a wall thickness of t1 is connected to a solid aluminum rod with a diameter of d2. The system is supported by a restraint at A and is subjected to loads at B and C.[D1 = 56 mm, t1 = 1 mm, d2 =d3 = 48 mm, E1 = 210 GPa, E2 = E3 = 55 GPa, P1 = 28 kN, P2 = 17 kN, L1 = 295 mm, L2 = 195 mm, L3 = 260 mm] Determine the movement of joint B with respect to support A?in mm Determine the movement of joint C with respect to support A?in mm Determine the movement of joint D with respect to support A?in mm
A semi-circular gate AB shown in the figure is hinged at B. Find the reaction at A. water 6 m A 4 m В
Quizes Syllabus Compute the hydrostatic force [Select] v acting for a gate 2.5 m wide and 2.0m long has Conferences a water on one side and is inclined with the horizontal as shown. Water is 1.60 m above the top of the gate. Compute the distance ( Select] v of the center of pressure from (B) and the force [ Select ] v perpendicular to the gate needed at the bottom (A) to open the gate. hinge gate 2m 45 to search IN %23
solve problem using the pressure-prism concept
The air above the liquid (S.G.=0.85) is under a pressure of 40kPa gage. The rectangular gate is 2.0m wide. a) Determine the hydrostatic force acting on the gate. b) Determine the location of the force measured from the hinge. c) Calculate the minimum value of P to hold the gate in place.
1. A tank is filled to a depth of 5 feet of water and is 8 wide by 10 feet long. Determine the hydrostatic force acting on the horizontal bottom and on the vertical ends of the tank. 3 m Hinge 2. The gate shown is rectangular and has dimensions 6 m by 4 m. What is the reaction at point A? Neglect the weight of the gate. Atmospheric pressure Stop 30 6 m Water