A machine works in three strokes whose total stroke length is 36 cm and completed in 2 minutes. The machine table accelerates uniformly from rest to maximum speed during the first stroke for 12 cm; then the table speed falls to half of the maximum cutting speed at the end of the second stroke for next 0.15 m. Then the speed reaches to zero in the remaining last stroke. Find the maximum cutting velocity of the machine in mm/s. O 6.67 O 10 400 0.15

A machine works in three strokes whose total stroke length is 36 cm and completed in 2 minutes. The machine table accelerates uniformly from rest to maximum speed during the first stroke for 12 cm; then the table speed falls to half of the maximum cutting speed at the end of the second stroke for next 0.15 m. Then the speed reaches to zero in the remaining last stroke. Find the maximum cutting velocity of the machine in mm/s. O 6.67 O 10 400 0.15

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

In a dc machine when the number of parallels paths is (a) and the number of poles is (p), thus for lap winding O a p O a = 2 ENG
Q3) In a two-excitation and two-pole machine, the rotor and stator of both poles are prominent relations The inductor of the rotor and stator is as follows: Lss =(0.5 + 0.2cos20) H Lrr =(0.8 + 0.3cos20) H Lsr =0.7coseH The resistance of the windings is zero. If the rotor is in the position 0 =60 ° and flows from the stator A sinusoid with an effective value of 10A passes and the rotor winding is short, medium torque Calculate the impact on the rotor
Q9 / What are the function of brushes , pole and commutator in DC machine
estion 1 "A DC machine consists of 4-poles and operating at 1500 rpm. Its frequency of the induced emf in armature is determined as 50 Hz" O True O False S A Moving to another question will save this response. e IT:P AR
8) the armature resistance of dc machines with number of poles > 2 is larger when the machine is: wave wound lap wound None of the above
.Find the torque when armature current is halved a.20 N-m b.5 N-m c.40 N-m d.10 N-m
An 8-pole DC machine has a simplex wave-wound armature containing 200 coils of 10 turns each. The resistance of each turn is 0.01 Ω. The flux per pole is 0.004 Wb. What is the internal resistance of the armature in ohms? What is the current absorbed by this machine in amperes at the instant it's connected to a 100 Vdc source? What is the internally generated torque produced by the armature of this machine in N-m at the instant it's connected to the 100 Vdc source? With the DC machine connected to the 100 Vdc source, what is the steady state angular speed of the machine in rpm? What is the internally generated voltage of the armature of this machine at steady state in volts?
An 8 pole, lap connected armature has 500 conductors has the flux per pole is 20 mWb is driven at the speed of 720 rpm, then the e.m.f generated in the machine is, O 220 V O 120 V O300 V O480 V
Describe the similarities in the construction of a DC motor and a DC generator. Please answer in short point wise and dont copy from other sources i will like lt
For 6 polar D.C machine armature has 36 number of slots and the type of winding is a double layer simplex lap winding. a. How many coils are present? b. What is the coil span in terms of number of slots? c. If each coil has 4 turns, then what is the total number of armature conductors presents? d. How many parallel paths will be their in the armature? e. Altogether how many brushes will be their?
1.Two identical shunt generators running in parallel, each with armature resistance of 0.02 ohms and field resistance of 50 ohms. The combined load current is 5000A. The field are so excited that the generated voltages of one machine is 610V and the other is 600V. The terminal voltage of this parallel combination will be. www Ish1 Rh1 a.350-360 V b.450-460 V c. 550-560V Rat www az G₂ Raz 5000 A Ish2
An 8 pole, simplex lap wound, shunt generatoe has 800 conductors and a flux per polw of 0.025Wb. The armature and shunt field resistances are 1 ohms and 45 ohms respectively. if a resistance of 11.25 ohms is connected as a load and the machine is running at 800 rpm. calculate the load cureent(in amp)