Answered: A material has the following…

A material has the following properties: density p = 8932 kg/m³, specific heat cp = 1.17 x 10-4 m²/s. Find the conductivity 380 J/kg-K, and thermal diffusivity & = [W/m-K]. Your Answer:

Principles of Heat Transfer (Activate Learning with these NEW titles from Engineering!)

8th Edition

ISBN:9781305387102

Author:Kreith, Frank; Manglik, Raj M.

Publisher:Kreith, Frank; Manglik, Raj M.

Chapter1: Basic Modes Of Heat Transfer

Section: Chapter Questions

Problem 1.71P: 1.71 The thermal conductivity of silver at 212°F is 238 Btu/h ft °F. What is the conductivity in SI...

See similar textbooks

Related questions

Q: A three-blade propeller of a diameter of 1.5 m has a rotational speed is 60 Hz, the activityfactor…

A: The objective of the question is to calculate the required thrust to weight ratio for an aircraft to…

Q: What is the mass of the bug?

Q: Determine the moments of inertia with respect to the centroidal axes of the following figure:

A: Given figure 2

Q: Q1/ Choose the correct answer: 1- When all forces (lift, weight, drag, thrust) and moments about the…

A: There are five questions in which we have to give the correct option.

Q: A motorcycle and rider have a combined mass of 350kg. The vehicle's velocity is 100 km/hr. The rider…

Q: Consider a wind farm composed of 100 turbines of 1-MW each. The rotor diameter D of each turbine is…

A: Given:

Q: A three-blade propeller of a diameter of 1.5 m has a rotational speed is 60 Hz, the activity factor…

A: Given:the diameter of the propeller is The rotational speed is The activity factor is The static…

Q: 3- A forced circulation boiler delivering 36 kg/s at 130 bar is operated with a circulation ratio of…

Q: A single-stage axial flow pump with outer radius r2 =0.240 m and inner radius r1=0.120 m is given.…

Q: A steel cantilever beam, of length 2L, has an l-section, see Figure Q3. The cantilever beam is under…

A: For the solution refer below images.

Q: Q.5- Consider the liquid-level control system shown in Figure below. assume that the velocity of the…

A: To find:Determine the transfer function.

Q: Q3: The response for the system shown is given by the plot of x(t) vs t. If the spring constant is…

Q: For Air: y = 1.4 Question B1 a) With the aid of sketches give a clear account of the operation of…

A: To calculate the mass flow rate, calculate area ratio, back pressure drawing

Q: A bridge truss extends x = 205 m across a river (shown in the figure below) where 0 = 43°. The…

Q: 1) Water (p= 1000 kg/m³, u=0.001 Pa-s) flows trough a horizontal asphalted cast iron pipe 20 cm in…

Q: 2-74. Determine the magnitude and coordinate direction angles of the resultant force, and sketch…

A: As per Bartleby's policy in case of multiple questions I can solve only first one.

Q: Explain if knowing the ratio between the thermal conductivity and the viscosity of a gas allows us…

A: Find outthe massthe heat capacitySizeGivenThe ratio between the thermal conductivity and the…

Q: a) What is the approximate direction of acceleration of point E? (North, South, South East)

A: The pulleys are rotating in the clockwise direction.And the angular acceleration is also showing in…

Q: The channel shape cross-section and the rectangular cross-section shown in the Figure Q4 are made of…

A: The solution is mentioned below

Q: Consider the manipulator shown in the following figure. (a) Explain the difference between forward…

Q: Q.11- Consider the positions servomechanism is shown in figure below. Assume the following numerical…

A: Find outDetermine the natural frequency and damping ratio of the systemgivenGain of potentiometer…

Q: The factors of safety at point H predicted by the maximum-distortion-energy theory (von Mises…

A: For the solution refer below images.

Q: Consider the bar in Figure 2, which has cross-sectional area A = 1·10−3 m2, modulus of elasticity E…

Q: A cross-section of a beam is shown in Figure Q2. If the shear force in this section is V = 281 KN,…

A: Given : The shear force in this section is The diagram is,

Q: Discuss the effects of five different production errors on the overall performance of manufacturing…

A: The detailed solution is mentioned below

Q: A three-blade propeller of a diameter of 1.5 m has a rotational speed is 60 Hz, the activity factor…

A: Given:The diameter of the propeller, The rotational speed, The activity factor, The static torque…

Q: A centrifugal pump having a head-capacity relationship given by the equation ha=180 – 6.10 X 10-4 Q2…

Q: Calculate the rotational speed. A, and acceleration, 0, for the mechanism in Fig. 3 if 8-50.fo 5 cm…

Q: A local shop is maintained at 101.3 kPa and 19oC. The air inside the shop is forced to leave at a…

Q: A cicular dise of 100 kg mass and Im diameter is supported between two bearings on a shaft of…

A: Given:To find:Angular velocity of precession.

Q: A 0.75-m x 1.5-m window is constructed of 6-mm-thick glass. On a cold night, the inside and outside…

A: “Since you have posted multiple questions with multiple sub parts, we will provide the solution only…

Q: (b) Using the provided data: cross-section width w= 12 mm, cross-section hight h=98 mm, ● length of…

Q: A sheet of aluminium alloy is reduced in thickness by 25% following a rolling operation. Tensile…

A: The objective of the question is to understand the impact of a rolling operation on the mechanical…

Q: B. Based on the data given below, determine if the fluid is a Newtonian or non-Newtonian fluid.…

A: Using the given data let's calculate the slope of the characteristic curve of the fluid.Shear stress…

Q: Q₁: The system shown has two masses. Beam of mass (J.*m L² kg.m²) rotates about fixed point (O) and…

A: The mass moment of inertia of the beam is The mass moment of inertia of the disk is,To find the…

Q: Solve the problem. A 11-in. connecting rod in an engine connects the wrist pin of a piston at point…

Q: 2.25 in. 90 lb C Force 4.5 in. A 180 lb 10° Replace the forces acting at A and D with an equivalent…

Q: 2. You are working for a glider manufacturer and have been asked to analyse the laminar boundary…

A: For the solution refer below images.

Q: For the beam shown, draw the Shear and Moment Diagrams for 3 loading cases below. For each load…

A: Given:The three loading conditions are given for the given beam;Case 1: downward, and downwardCase…

Q: The channel shape cross-section and the rectangular cross-section shown in the Figure Q4 are made of…

A: Solution is provided below

Q: 3.3 Evaluate the specific physical exergy, ePH, in kJ/kg, of a stream of (a) saturated water vapor…

Q: vertical distance from the location where the maximum shear stress occurs

Q: The inner diameter of this shaft is 80 mm and the outer diameter is 100 mm. The applied loads are…

A: Given:To find:Maximum allowable load P.

Q: If P=9.8kN Determine the reaction forces at Supports A and D

Q: Work out the inverse kinematics of a scara robot assuming that the first and second rotatingrobot’s…

A: The objective of the question is to calculate the inverse kinematics of a SCARA (Selective…

Q: Q6) A 50-cm-long, 800-W electric resistance heating element cm and surface temperature 120°C is…

A: The length of heating element = 50 cm = 0.5 mThe diameter of heating element = 0.5 cm = 0.005 mThe…

Q: Q2: For mass-spring system shown. The mass is given an initial displacement x(0)= 0.1 m, and…

A: The stiffness of the springMass of the blockInitial displacementIt is released from the rest so the…

Q: Air (assumed incompressible) flows steadily into the square inlet of an air scoop with the…

Q: Q3 A portable conveyor is to be raised and lowered using the double power screw arrangement as shown…

A: Given:Value of the total load, Design stress of the power screw, Lead angle of the screw,…

Q: The seesaw is pivoted in the middle, and the mass of the swing bar is negligible. (Figure 1) Find…

A: We know that Lets calculate torque, torque net is equal to: Calculation of moment of inertia:…

Concept explainers

Fluid Dynamics

The study of the flow of gases and liquids, usually in and around solid surfaces, is known as fluid dynamics in physics and engineering. Fluid dynamics, for example, can be used to evaluate the movement of air through an airplane wing or the surface of a vehicle. It can also be used in ship design to increase the speed at which ships pass through water.

Question

solve show all steps/solution

=
A material has the following properties: density p = 8932 kg/m³, specific heat cp -
1.17 x 10-4 m²/s. Find the conductivity
380 J/kg-K, and thermal diffusivity &
=
[W/m-K].
Your Answer:

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1: Given

VIEW

Step 2: solution

VIEW

Solution

VIEW

Step by step

Solved in 3 steps with 3 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.

Similar questions

A house wall is composed of 3 layers in series to each other. There is an Aluminum layer that is 4 cm thick, Copper layer that is 6 cm think and Gold layer that is 3 cm thick. What is the total conductivity of the wall and its R-value in units of ft2.F.hr/Btu? [KAl = 2.37 W/cm.C, KCu = 4.01 W/cm.C, KAu = 3.17 W/cm.C]
Consider a wall of thickness 50 mm and thermal conductivity 14 W/m.K, the left side (x-0) is insulated. Heat generation (q) is present within the wall and the one dimensional steady-state temperature distribution is given by T(x) = ax +bx+c [°C], where c = 200 °C, a = -1285 °C/m , b= needs to be determined, and x is in meters. What is the heat generation rate in the wall (kW/m )? 9, K 9(L) L> Insulation
Find the axial stress (Subscript[\[Sigma], z]) and axial strain (Subscript[\[Epsilon], z]) for a thick-walled circular pipe subjected to an internal pressure Subscript[p, i] for the following three cases:a) the pipe is long and open (plane strain)b) the pipe is short and open (plane stress)c) the pipe is is closedExpress the above solutions in terms of the pressure Subscript[p, i], the the pipe inner and outer radii and the material constants.
Question 1: [Simple stresses] 1. A hydraulic system is used to apply a force in an external fixation device to hold broken ends. The piston of this hydraulic ram is 30 cm in diameter and the water pressure (shaded portion of the sketch) is 3 MN/m² as shown in Figure Q1.1. 3 MN/m? 30 cm 4 cm Figure QI.1 Hydraulic system Determine: 1.1. The stress in the piston rod which has dimeter of 4 cm 1.2. The elongation of the 2 m long piston rod. Take Young's modulus as E = 200 GN/m²
CALCULATE THE FOLLOWING: We performed the experiment to measure MATERIAL 1 - BRASS the thermal conductivity of 2 materials (Brass & Steel) in the laboratory and measured the following tabulated values: Calculation for Brass Quantities Values Material 1- BRASS Calculated Power (Q') W (Diameter = 25mm) Area of cross section (A) m2 Power Difference in Temperature Temperature (°C) between two points (AT) °C Difference in distance between two points (Ax) m Q' 1 2 3 (W) Thermal conductivity of brass (kp) W/m°C 4 5 6 8 9. 14.65 79 77.4 76 50.1 46.5 42.4 36 34.5 33.6 MATERIAL 2 - STEEL Calculation for Steel Material 2 - STEEL %3D Quantities Values Calculated (Diameter = 25mm) %3D Power (Q') W Power Area of cross section (A) m2 Temperature (°C) Difference in Temperature between two points (AT) °C Q' 1 |(W) Difference in distance between two points (Ax) m 2 3 7 8 14.2 88.6 87.5 85 33.9 33.6 32.4 Thermal conductivity of steel (kg) W/m°C
II. A circular column is made of concrete [E. 4.2(10³)ksi] while being reinforced with six steel rods [Est = 29 (10³)ksi]. It is acted upon 4 in. - 30 kip by an axial force of 30 kip as shown in the figure to the right. Each rod has a diameter of 0.85 in. 3 ft Solve for the following: a) Force in each steel rod, Pst b) Force in the concrete, P. c) Stress in each steel rod, Ost = kip kip %3D ksi d) Stress in the concrete, oc = ksi
Question 3 We can make an energy dense capacitor by stacking layers of conductors separated with a dielectric, as shown below. Then, every other layer is connected together and held at the same voltage. V₁ V2 Suppose that all layers are identical and a single pair of plates has a capacitance of 21 F. What is the equivalent capacitance of this setup? Enter your answer in units of [Farads (F) ], rounded to the nearest one.
The previous solution makes no sense. Please provide correct handwritten solution. [The answer must he in handwritten format only , Please consider it]
The rate of heat flow equation is Q O A. Thermal resistance OB. Thermal coefficient O C. None of these OD. Thermal conductivity Type here to search KA(T₁-T₂) X E The term X ΚΑ is known as 99+
Heat Transfer Design a 1D conduction experiment to measure thermal conductivity of 3 different materials that can be done in your kitchen. Identify the variables that will be changed and write a detailed protocol.
3. Thermal conductivity of a substance is measured as k = k, TIT, . Find an average value for thermal conductivity in the temperature range of T1 and T2. [Ans. = (k, /272 xT} 2 – T}/2) (T2 – T;) 1|
Engineering Mechanics (Method of Members: Frames/ Composite Structures)First Picture: ExampleSecond Picture: Assignment Question