a new computer drive is proposed to have a disc, as shown in the figure below. The disc is to rotate at 10,000 rpm, and the readers head is to be positioned 0.0005 in above the surface of the disc. Estimate the shearing force on the readors head as a result of the air between the disc and the head. use Mair = 3.737 x 10¹ lb-s (US STANDARD ATM, air at sea level. 2 ft²

a new computer drive is proposed to have a disc, as shown in the figure below. The disc is to rotate at 10,000 rpm, and the readers head is to be positioned 0.0005 in above the surface of the disc. Estimate the shearing force on the readors head as a result of the air between the disc and the head. use Mair = 3.737 x 10¹ lb-s (US STANDARD ATM, air at sea level. 2 ft²

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

The nominal power of the wind turbine is 2 MW at wind speed 11.5m/s, generator efficiency is 94%, gear box efficiency is 65%, power coefficient of blades is 59%. What would be the diameter of the rotor? (Given: density of air = 1.225 kg/m3) %3D
A double acting cylinder has a system pressure of 0.1750 kN/cm to produce an extraction force of 0.065 MN and Retraction force of 49 KN. The available extension velocity is 16500 m/min. (a) Find the diameter piston in mm (b) Find the diameter of ram in mm for the same system pressure. (C) Flow rate in Ipm (d) Retraction velocity E A- BI E
2.5-L bench scale bioreactor is used for the production of recombinant P64K protein from Neisseria meningitides. The dimensions for the bioreactor are Dt 12.9 cm, ratio Di/Dt = 1/3 and N = 700 rpm. With the scale up factor of 2.24, determine the impeller tip speed (m/s) for the pilot scale bioreactor based on constant impeller tip speed and constant power consumption per volume. Predict which scale up method might give a higher concentration of P64K, if the demand of dissolved oxygen plays an important role.
A wind turbine with 10 m diameter rotor. Speed of the rotor at 10 m/s wind velocity is 130 rpm and its power coefficient at this point is 0.35. Calculate the tip speed ratio and torque coefficient of the turbine. What will be the torque available at the rotor shaft? Assume the density of air to be 1.24 kg/m3
Water at 20"C Bows through the pump impeller shown in the figure below, where the inner and outer diameters of the impeller are 160 mm and 400 mm respectively, and the width of the pump blades is 55 mm Part A Wan- μA Estimate the shaft power required to drive the pump at this operating condition Express your answer to three significant figures and include appropriate units. Value Blade Pump impeller The impeller rotates at 3600 rpm Under a particular operating condition, water enters in a direction normal to the inflow surface, the component of the outflow velocity normal to the outflow surface. V is equal to 17 m/s, and the magnitude of the absolute velocity, V, at the outflow surface is 33 m/s Submit Request Answer Units Outflow surface Inflow surface ? 160 บท 400 mun
There are two double-acting pneumatic actuators, the extension of each one is executed in 5 seconds at 80 psi and recoil in 4 seconds at 30 psi, the travel of both is 12 inches, the diameter of the piston is dp = 4 "and of the rod dv = 1"a) Determine the compression ratios. The local atmospheric pressure is 79kpa = (11.5 psi)b) Determine the air consumption in cubic feet per minute of free air PCMc) Determine the average air consumption for each.d) Propose the regulation values of the pressure switch, system pressure and safety valve
The nominal power of the wind turbine is 3MW at wind speed 11.5m/s, generator efficiency is 94%, gear box efficiency is 0.75, power coefficient of blades is 0.59. What would be the diameter of the rotor
A petrol engine has a cylinder diameter and stroke of 120mm and 235 mm respectively. The clearance volume is 0.00029 m3. Find the total volume of the cylinder in m3? The total volume in m3?
The bore and stroke of an air compressor are 276mm and 164mm, respectively. If the piston displacement is 0.049m3/sec, what is the operating speed of the compressor?
Q1: An engine of multi-cylinder is to rotate at a speed of 600 r.p.m. At draw the turning moment diagram to a scale of 1 mm = 250 N-m and 1 mm = 3°, the areas below and above the mean torque line in mm^2 are: + 160,- 172, + 168, 191, + 197, - 162. The speed is to be kept within + 1% of the mean speed of the engine. Determine the necessary moment of inertia of the flywheel. Determine the suitable dimensions of a rectangular flywheel rim if the breadth is twice its thickness. The density of the cast iron is 7250 kg/m3 and its hoop stress is 6 MPa. Assume that the rim contributes 92% of the flywheel effect.
A double acting pneumatic cylinder has a diameter of 100 mm. The rod is 40 mm diameter and the stroke is 120 mm. It must produce a pushing force of 12 kN. The flow rate available in both directions is 12 dm3 /minit. Calculate:- The system pressure needed The force with which it pulls given the same pressure iii. The velocity on the extension The velocity of retraction The power used on the outstroke
A certain fan delivers 340 m3/min of air at a static pressure of 25.4 mm of water gagewhen operating at a speed of 400 rpm and requires an input of 3 kW. If in the sameinstallation 425 m/min of air are desired, what will be the new static pressure in termsof mm of water and fan power required?