A physics experiment is set up using two pulleys, a string, and a weight as shown below. The larger pulley has a radius of 20 centimeters, and the smaller pulley has a radius of 5 centimeters. The distance between the centers of the pulleys is 51 centimeters. The string is pulled tightly across both pulleys so that AB is a common tangent of the pulleys. Find the length of string from A to B to the nearest tenth of a centimeter. weight

A physics experiment is set up using two pulleys, a string, and a weight as shown below. The larger pulley has a radius of 20 centimeters, and the smaller pulley has a radius of 5 centimeters. The distance between the centers of the pulleys is 51 centimeters. The string is pulled tightly across both pulleys so that AB is a common tangent of the pulleys. Find the length of string from A to B to the nearest tenth of a centimeter. weight

University Physics Volume 1

18th Edition

ISBN:9781938168277

Author:William Moebs, Samuel J. Ling, Jeff Sanny

Publisher:William Moebs, Samuel J. Ling, Jeff Sanny

Chapter10: Fixed-axis Rotation

Section: Chapter Questions

Problem 120AP: A grindstone with a mass of 50 kg and radius 0.8 m maintains a constant rotation rate of 4.0 rev/s...

See similar textbooks

Similar questions

A grindstone with a mass of 50 kg and radius 0.8 m maintains a constant rotation rate of 4.0 rev/s by a motor while a knife is pressed against the edge with a force of 5.0 N. The coefficient of kinetic friction between the grindstone and the blade is 0.8. What is the power provided by the motor to keep the grindstone at the constant rotation rate?
The cylindrical head bolts on a car are to be tightened with a torque of 62.0Nm . If a mechanic uses a wrench of length 20 cm, what perpendicular force must he exert on the end of the wrench to tighten a bolt correctly?
A 5kg weight is attached to a pulley which hav radius 8.65cm. Through what angle (in degrues) must the pulley be rotated to raise the wright 2.00 meters? IRound your answer to 4 decimals.
When a wrench is rotated the magnitude of the torque is 26N.m A 95-Force is applied 35 Cm from the fulcrum. At what angle to the wrench is the force applied?
F Pivot d The length of the pool cue is 1.5 m. A force of 11 N is applied at an angle 55°, a distance 0.7 meters from the pivot. What is the torque created? Answer to 3 sig figs.
In this problem you will be given pictures of two vectors, r and F. Based on these two vectors you should A determine the direction of the torque, T = r x F. Possible answers include left, right, up, down, in, out. les ne What is the direction of the torque vector? Submit Answer Tries 0/2 re 1 Len nce What is the direction of the torque vector? Submit Answer Tries 0/2 F x onai vel
(a) Convert 41.0° to radians, using the appropriate conversion ratio. rad (b) Convert 2. 46 rad to degrees. (c) If a circle has radius 1.60 m, what is the arc length subtended by a 41.0 angle?
The tire on a unicycle h a diameterof 24 inches and rotates at a rate of 187 revolutions per minute. Find the linear sped in miles per hour.
A rope te wound around a shaft 10cm in diameter. If a pull of 500N is exerted on the rope, what torque is imparted to the shaft?
Angle of rotation is often measured in revolution. Please determine how many radians is equivalent to 5.65 revolutions.
Find the number of revolutions of a bicycle wheel of diameter 0.7 mWhen the bike goes a distance of 22 m down the street.
You pull downward with a force of 28 N on arope that passes over a disk-shaped pulley of mass 1.2 kg and radius0.075 m. The other end of the rope is attached to a 0.67-kg mass.(a) Is the tension in the rope the same on both sides of the pulley?If not, which side has the greater tension? (b) Find the tension inthe rope on both sides of the pulley