help A pipe has an outside diameter of 3m and an inside diameter of 2.9m. It isacted upon by a tensile force of 200N. What is the stress acting on the pipe?A solid round bar of diameter 250mm has a tensile force of 0.2kN acting onit. What is the stress acting on the bar?A tensile test specimen has a length of 190mm. This is increased by 0.045mmwhen subject to an applied force. Calculate the strain?A material has a length of 300mm. This is increased by 0.02mm when subjectto an applied force. Calculate the strain?A concrete cuboid section of material 15mm x 10 mm and 2600mm long, issubject to an axial load of 450ON. It has a Young's Modulus of Elasticity of 14GN/m2. Calculate how far will the material compress?An aluminium cuboid bar of cross section 9mm x 8 mm and 1500mm long, issubject to an axial load of 500ON. It has a Young's Modulus of Elasticity of 69GN/m2 Determine the distance the bar will compress due to the axial load.

Dear student, According to the guidelines I am allowed to answer only first…

Answered: A pipe has an outside diameter of 3m…

Mechanics of Materials (MindTap Course List)

9th Edition

ISBN:9781337093347

Author:Barry J. Goodno, James M. Gere

Publisher:Barry J. Goodno, James M. Gere

Chapter7: Analysis Of Stress And Strain

Section: Chapter Questions

Problem 7.7.15P: A brass plate with a modulus of elastici ty E = 16 X 106 psi and Poisson’s ratio a = 0.34 is loaded...

See similar textbooks

Similar questions

A solid round bar of diameter 250mm has a tensile force of 0.2kN acting on it. What is the stress acting on the bar?
A specimen of titanium alloy is tested in torsion and the shear stress–strain diagram is shown in Fig.a. Determine the shear modulus G, the proportional limit, and the ultimate shear stress. Also, determine the maximum distance d that the top of a block of this material, shown in Fig. b, could be displaced horizontally if the material behaves elastically when acted upon by a shear force V. What is the magnitude of V necessary to cause this displacement?
Find stress of a aluminum cylinder of diameter 12.8mm and gauge length 50.8mm. The force applied is 47,500N.
Calcuate torsion From Point A to Point C, Calcuate Bending From Point A to Point B and Point A to Point C. Draw a FBD from point A to point B and another for point A to C indicating what stresses are been calculate. Use the stress tensor and stress cube to Indicate what forces are acting at point A. Force apply at point B is 70lb Distacen from Point A to B is 12 in or 1 feet long Distacen from Point A to C is 3 in Handle diameter 0.625 in
lin. = 0.2 x 103 in. You test a concrete cylinder having a diameter of 6.00 in and a gauge length of 12 in by applying compression forces. The results of your test are reported in the table as load vs. contraction. Draw, by hand on engineering paper, a stress-strain diagram using scales of: 1 in. = 0.5 ksi in. From the diagram, determine approximately the Modulus of Elasticity. Load (kip) Contraction (in) 0.0 0.0000 5.0 0.0006 9.5 0.0012 16.5 0.0020 20.5 0.0026 25.5 0.0034 30.0 0.0040 34.5 0.0045 38.5 0.0050 46.5 0.0062 50.0 0.0070 53.0 0.0075
What force is required in Newton to punch a 30-mm diameter hole in a plate that is 15 mm thick? The shear strength is 350 MN/m^2. question 2: A type of stress that acts coplanar with cross section of material.
a 12mm thick steel tire has a width of 110mm and an internal diameter of 800mm. It is heated and shrunk onto a steel wheel 800.50mm in diameter. The modulus of elasticity of steel is 200gpa. Which of the following most nearly gives the comprehensive pressure between the tire and the wheel? A 3.30 mpa B 3.90 mpa C 3.75 mpa D 4.35 mpa
(d) Define Modulus of Resilience 2. Draw the stress-strain diagram for a typical ductile material and locate the salient points onit 3. A bar of 25 mm diameter is tested in tension. It is observed that when a load of 60 kN is applied, the measured over a gauge length of 200 mm is 0.12 mm and contraction in diameter is 0.0045 mm. Find Poissa 4. A circular rod of diameter 16 mm and 500 mm long is subjected to a tensile force 40 kN. The modulus of e steel may be taken as 200 kN/mm?. Find the elongation and strainin the bar due to applied load. 5. Define (a) Resilience (b) Proof resilience PART -B structions: Part B consists of 3 Units. Answer any one full question from each unit. Each questioncarries 8 marks and may have su 1. A steel circular bar has three segments as shown in the fig. Determine the total elongation ofthe bar. Take E = 210 GPa. 300 kNI 330 kN 30 mm 50KN 15 mm 20 mm 80 kN A + 150 mm 200 mm 250 mm B. D (OR)
A pipe has an outside diameter of 0.7 inches and inside diameter of 0.12 inches. A force of 144 lbs is applied at the end of a 1.1 ft lever arm, causing the pipe to twist. What is the maximum stress in the pipe in psi? the correct answer is 28248 please show steps!!
A tensile force. of 120 kN is applied on a 0.02-m diameter and 2-m long rod. After applying the load, the diameter decreases to 0.01998 m and the length increases to 2.01 m. The true stress on that rod is?
A rectangular block of size in mm as shown in fig., is subjected to stressess. Determine the change in linear dimension and change in volume of the block. Take E = 200 X 106 kPa and poisson's ratio = 0.3. 140MPA 50MPA 140MPA 50 MPa 900 600
Find the value of stress Force 2.2 N Area=2 m2

SEE MORE QUESTIONS

Recommended textbooks for you

Mechanics of Materials (MindTap Course List)

Mechanical Engineering

ISBN:

9781337093347

Author:

Barry J. Goodno, James M. Gere

Publisher:

Cengage Learning

Mechanics of Materials (MindTap Course List)

Mechanical Engineering

ISBN:

9781337093347

Author:

Barry J. Goodno, James M. Gere

Publisher:

Cengage Learning

SEE MORE TEXTBOOKS