A pressure management system (a diaphragm sensor giving a capacitance change with output processed by a bridge circuit anddisplayed digitally) is stated as having the following characteristics:• range: 0-125 KPa· accuracy: F 1.8 % of FSD· temperature sensitivity: 7 0.104 % of FSDIf the instrument measures 28 KPa at an ambient temperature of 30.1, what is the lower bound of the actual value?No label, no unit, just the number.

Given: For a diaphragm sensor, range: 0-125 kPa, accuracy: ∓1.8% of FSD, temperature sensitivity:…

A pressure management system (a diaphragm sensor giving a capacitance change with output processed by a bridge circuit and displayed digitally) is stated as having the following characteristics: • range: 0-125 KPa · accuracy: + 1.8 % of FSD · temperature sensitivity: + 0.104 % of FSD If the instrument measures 28 KPa at an ambient temperature of 30.1, what is the lower bound of the actual value? No label, no unit, just the number.

A pressure management system (a diaphragm sensor giving a capacitance change with output processed by a bridge circuit and displayed digitally) is stated as having the following characteristics: • range: 0-125 KPa · accuracy: + 1.8 % of FSD · temperature sensitivity: + 0.104 % of FSD If the instrument measures 28 KPa at an ambient temperature of 30.1, what is the lower bound of the actual value? No label, no unit, just the number.

Delmar's Standard Textbook Of Electricity

7th Edition

ISBN:9781337900348

Author:Stephen L. Herman

Publisher:Stephen L. Herman

Chapter30: Dc Motors

Section: Chapter Questions

Problem 6RQ: What is CEMF?

See similar textbooks

Similar questions

4. An RC filter stage (R = 33 0, C = 120 HF) is used to filter a signal of 24 V dc with 2 V rms operating from a full wave rectifier. Calculate the percentage ripple at the output of the RC Section for a 100-mA load. Also calculate the ripple of the filtered signal applied to the RC stage. *****END*****
Repeat example 35 for FWD and firing angle Fa) 60°. 215 l65 D1985 Example 35: A full wave rectifier used 220V, with firing angle 10° ,total resistance load 5 KQ, inductance 2.34 H,and frequency 60HZ, Draw and calculate: (a) VD.c and Ipc (b) VD.C(Max) (c) Vn (d) Vorms-
The sensitivity of a PMMC instrument is 10k /V. If this instrument is used in a rectifier type voltmeter with half wave rectification, the sensitivity will be:
CIRCUIT DIAGRAM : D1 IÑ4001 AC Source RL 1K Q VOUT PROCEDURES : 1. Construct the half-wave rectifier circuit as shown. 2. Monitor the input voltage using the oscilloscope. Adjust the oscilloscope to show at least two complete cycles of the input signal. Draw the input waveform in Graph 1 and measure the peak-to-peak value. Record this in Table 1. Convert this value into RMS value using the formula: 3. 4. Vp-p Vp-p P-P VRMS 2.828
A full-wave rectifier produces a 32V peak rectified voltage from a 50Hz ac source. Determine the filter capacitor needed to provide a DC output voltage 24V across a 500 ohm load.
Single phase half sinusoidal wave controlled rectifier with (? = 30?) pure resistive load (Vs =220 v. f=60 Hz, R=10Ω) Determine the average output voltage Vo  Determine the r.m.s value of the output voltage
Question 3 Consider the following cirucit: in + V1 R1 5 PULSE (0 2 1 1 1 1) (Note again the unrealistic diode characteristics.) The input is a ramp: 2.0V- 1.6V- 1.2V- 0.8V- 0.4V- 0.0V- 0.0s 0.2s 0.4s 0.6s 0.8s out .tran 2 .model diode D(Ron=5 Vfwd=1 Roff=1G) V(in) D1 diode 1.0s 1.2s 1.4s 1.6s 1.8s 2.0s The output voltage is similar to the input voltage, except that it breaks at a certain voltage and reaches a different final value. Find the break voltage and the final value of the output.
(VPP of input is 18 V. Bias voltage is 2 V. The positive peak value of output waveform for the given circuit diagram is. Diode is germanium) R1 D, VOuT VIN VsAS
A 60 Hz sinusoidal voltage with an RMS value of 120 V is applied to a single-phase full-wave SCR rectifier. The DC output voltage of the rectifier is 101 V, the firing angle (in degrees) of SCR is would be: O A. 36 O B. 45 O C. None of the other choices are correct O D. 30 O E. 60
Draw and explain the circuit of a simple AM demodulator using Junction diode ( draw the input and output waveforms )
6. A conductor carries a current that is equivalent to a 2.5 amp continuous current in one direction and a superimposed full-wave rectifier in the opposite direction. What is the maximum value of the latter if the average conductor current is zero?
For the given circuit: if Vin = 200 V rms, R, = 2.2 k2, f = 60 Hz, answer the following questions (assume practical diodes). a) Calculate the peak output voltage, Vp(rect) b) What is the peak forward current I, through each diode and the average power P(avg) that is delivered to R c) If a capacitor filter is connected from the rectifier output to ground, and the peak to peak ripple voltage was found to be Vr(pp) = 0.8 V, determine the value of the capacitor. d) Draw the output voltage waveform for the unfiltered rectifier and for the filtered rectifier in relationship to the input waveform (show two full cycles). Show all the necessary values on the graphs. 4:1 DI Vin RL D2 elle lelll