A prestressed T-beam shown which is reinforced with a bonded tendon having an area Aps=1580 mm?,fo'=34.5 MPa, fou=1862 MPa, and the effective stress after losses, fse=1102 MPa, „foy=1713 MPa. Span ofbeam is 6 m.а.What is the value of the stress in prestressed reinforcement at nominal strength (fps)b.Find the ultimate moment capacityC.Find the live load1220 mm-10.85 fo'|80부N.A.600d-a/2Aps60T=Aps fps250

Answer We are given Bonded tendon Tendon Area Aps = 1580 mm2 f'c = 34.5 Mpa fpu =1862 Mpa Effective…

A prestressed T-beam shown which is reinforced with a bonded tendon having an area Aps=1580 mm?, f.'=34.5 MPa, fou=1862 MPa, and the effective stress after losses, fse=1102 MPa, fpy=1713 MPa. Span of beam is 6 m. а. What is the value of the stress in prestressed reinforcement at nominal strength (fps) b. Find the ultimate moment capacity с. Find the live load 1220 mm- 10.85 fo' 80 a NA.- 600 d-a/2 Aps 60 T=Aps fps 250

A prestressed T-beam shown which is reinforced with a bonded tendon having an area Aps=1580 mm?, f.'=34.5 MPa, fou=1862 MPa, and the effective stress after losses, fse=1102 MPa, fpy=1713 MPa. Span of beam is 6 m. а. What is the value of the stress in prestressed reinforcement at nominal strength (fps) b. Find the ultimate moment capacity с. Find the live load 1220 mm- 10.85 fo' 80 a NA.- 600 d-a/2 Aps 60 T=Aps fps 250

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

Determine the prestressing steel area required for the precast concrete T-beam. Use the following data: Total moment = 250 kN-m Effective stress fse= 862 MPa Allowable concrete stress = f.=11 MPa Consider zero stress at the bottom of the beam I=3673x106 mm4 A=103125 mm² Eccentricity = 271.6 mm Centroid of steel is located at 100 mm from the bottom of the beam. Select one: a. 591.97 mm b. 789.29 mm 2. C. 443.98 mm 2. d. 986.61 mm
A beam, which is rectangular, has a base of 250 mm, and d = 625 mm. The beam is singly reinforced, where the recorded strain in the steel is 0.005, and the strain in the concrete is 0.003. fc' = 20.7 MPa, fy = 414.6 MPa. Note: As is not Given a) Determine the value of "a". %3D
A rectangular steel block is 75 mm in the x-direction, 50 mm in the y-direction and 100 mm in the z direction. The block is subjected to triaxial loading consisting of three uniformly forces as follows: KN tension in the x-direction, 250 KN compression in the y-direction, and 240 KN tension in the z-direction. If u = 0.3 andE = 200 GPa, Determine the total resulting strain in the x- direction. %3D
A rigid steel plate is supported by three posts of high-strength concrete each having an effective cross-sectional area A = 40,000 mm2 and length L = 2 m (see figure). Before the load P is applied, the middle post is shorter than the others by an amount s = 1.0 mm. The allowable compressive stress in the concrete is 20 MPa and E of concrete is 30 GPa. What is the minimum load P (kN) needed to close the gap? P S
A singly reinforced beam will be provided with the reinforcing bars corresponding to 90% of the maximum reinforcement ratio specified in the ACI Code for a tension-controlled (i.e., underreinforced) design. The materials used have the following properties: ??′ = 4000 psi, ?? = 80000 psi, ?? = 0.002 Estimated the steel area ?? Sketch the stress and strain distributions in the beam cross-section. The diagrams should show the location of the neutral axis and the compressive/tensile forces acting on the cross-section Calculate the nominal moment strength ?? and the design moment strength ??? [in kips-ft] Briefly explain how the formula of moment calculation can be derived Assume that the design moment strength is less than the factored moment. Hence, compression rebars will be added. The effective depth is ?′ = 1.5′′. Determine the steel area of compression rebars ??′ so that the compression bars yield at the flexural failure Based on ??′ determined in part d calculate the nominal…
A singly reinforced rectangular section has a width of 250mm and an effective depth of 460mm. The concrete has a compressive strength of 21MPa. The steel has a yield strength of 275 MPa and E = 200,000 MPa. Calculate the ideal flexural strength for the following areas of steel: a. 2580 mm² b. 5160 mm² c. The value at balanced failure
Problem 6: The wood beam is subjected to a load of 12 kN. Determine the transverse shear stress at point A is located 75 mm from the lower surface of the beam. Also what is the bending normal stress at A? 12 KN + 300 mm TH 200 mm -2 m---1 4.1 75 mol IM
A rectangular pretensioned beam has concentric prestress force of 1000 KN. The beam is 300 x 500 mm in dimension and M20 grade of concrete is used with creep coefficient of 1.6 and residual shrinkage strain of 3 x10-4. Ast = 500 sq.mm. Find the following: a. Loss due to elastic shortening use Est = 200 GPa and Ec = 5700(Fc)^1/2 b. Loss due to creep c. Loss due to shrinkage d. Total loss of prestress
A pretensioned member with a dimension of 250mm x 360mm is subject to an eccentric tendon that is located 105mm from the soffit. Area of the prestressing steel to be 502 sq. mm and the modulus of elasticity is 200 GPa. The Modulus of elasticity of concrete is 36.8 GPa. Creep coefficient = 1.6 and the shrinkage strain = 3 x10^6. Assume a 5% steel relaxation. Find the total prestressed loss in percentage.
1. The prestressed beam is pre tensioned by a bonded prestress tendon having an area Aps = 650 mm2. fpu = 1728 MPa fpe = 988 MPa %3D fpy = 1486 MPa fc' = 27.6 MPa 300 mm |120 400 mm 600 mm 120 100 a. Find the value of the stress in prestressing reinforcement at nominal length. b. What is the design moment strength of the beam c. Is the beam over or under reinforced.
A prestressed concrete beam has the following characteristics: a width of 300mm overall depth of 600mm prestressing tendons are placed at a distance “e” below the NA of the beam the applied prestressing force is P in kN there is 15% loss of prestress 4. Find e in mm when the compressive stresses at the top and bottom of the beam are 0 MPa and 16MPa, respectively.
In all Questions use the Working Stress Method and the flowing material 25 MPa and f, = 420 MPa. properties f = If the stress in the top fiber of the concrete is f = 12.5MPa and in the steel is 400 MPa. Ec 25000 MPa, Es 200000 MPa. Determine the following: 1-Maximum strain in concrete 2- Maximum strain in steel and 3- Flexural strength of the section (the moment M) P 500 mm 300 mm