a) Programmable Read-Only Memory (PROM) is a computer memory chip whichis programmable once it is created and the information cannot be erasedImplement the following Boolean functions using PROM.F1(A1, A0) =F2(A1, A0) =m(3,5,7),m(4,5,7)Major TopicProgrammable Read Only Memory (PROM)Major TopicProgrammable Logic Array (PLA)b)A combinational circuit is defined by the function F1= Σ m (3,5,7),F2 = Σ m (4,5,7). Implement the circuit using a PLA which consists of 3 inputs(A, B and C), 3 product terms and two outputsBloomsDesignationAPMajor TopicCombinational Logic CircuitsBloomsDesignationANMajor TopicMemories Devicesc) A combinational circuit has four inputs and one output, the output equal 1 when:1 - all the inputs are equal to 1 or2- non of the inputs are equal to 1 or3- an odd number of inputs are equal to 1.Design the logic circuit.BloomsDesignationAPd) Using the required steps convert a D flip-flop to T flip-flopSporeBloomsDesignationANStoreScoreScore

As per bartleby guidelines if multiple questions are posted in single image, only first question…

a) Programmable Read-Only Memory (PROM) is a computer memory chip which is programmable once it is created and the information cannot be erased Implement the following Boolean functions using PROM. F1(A1, A0) = F2(A1, A0) = m(3,5,7), m(4,5,7) Major Topic Programmable Read Only Memory (PROM) Blooms Designation AP Sobre

a) Programmable Read-Only Memory (PROM) is a computer memory chip which is programmable once it is created and the information cannot be erased Implement the following Boolean functions using PROM. F1(A1, A0) = F2(A1, A0) = m(3,5,7), m(4,5,7) Major Topic Programmable Read Only Memory (PROM) Blooms Designation AP Sobre

Systems Architecture

7th Edition

ISBN:9781305080195

Author:Stephen D. Burd

Publisher:Stephen D. Burd

Chapter2: Introduction To Systems Architecture

Section: Chapter Questions

Problem 2VE: A(n) __________ is a storage location implemented in the CPU.

See similar textbooks

Similar questions

Category: CPU Wiring Look at the following (incomplete) diagram of the Hack CPU taken from figure 5.9 of the textbook. ALU output outM instruction AM inM writeM A addressM inc reset PC po Match the wires A, B, C, D and E with the logic expression that describes the signal they should carry. The logic expressions use the operators not (!), and (&&) and or (I). The 16 wire instruction is named instr. The A and C instruction formats are: A-instruction: 0 V. V. V C-instruction: 1 1 1 a c1 c2 c3 c5 c6 d1 d2 d3 j1 j2 j3 Mire number: 15 14 13 12 11 10 9 8 6. 4 3 1 instr[15) && instr[3] B. instr[14] ALU
Design an 8 bit calculator in assembly language using emu 8086 that perform thefollowing functionalities: Take input from user Perform 8 bit addition Perform 8 bit subtraction Display result
The Register indirect addressing mode is: Immediate Operand Addressing Mode Register Operand Addressing Mode Memory Operand Addressing Modes Direct addressing mode
(d) The table below shows the ALUcontrol signal of the datapath we discussed in class. Instruction Funct ALU Орсode ALUop ALU action operation field control Iw 00 load word XXXXXX add 0010 Sw 00 store word XXXXXX add 0010 beq 01 branch equal subtract 0110 XXXXXX R-type 10 add 100000 add 0010 R-type 10 subtract 100010 subtract 0110 R-type 10 AND 100100 AND 0000 R-type 10 OR 100101 OR 0001 R-type 10 set on less than 101010 set on less than 0111 You want to add the bne instruction into the datapath, which already includes the required hardware for the instruction. Write out the ALUop for bne and how you can determine whether the bne results in the branch to be taken.
Write the microprocessor code that collects (33)16 data with (2F)16 information
Convert the C code below into RISC-V assembly language for the following scenarios: 1) Starting address of array A is x3 2) variable last is assigned to register x12 3) the return value of the procedure is assigned to register x20 Note that it is a non-leaf procedure
The Register indirect addressing mode is: Immediate Operand Addressing Mode mcq question Register Operand Addressing Mode Memory Operand Addressing Modes Direct addressing mode
ASSEMBLY The ROR instruction is only suitable for signed integers. True False
Consider a microprocessor based board which has 7-segment and Led is connected to it. Design an assembly language code such that input from user is taken; when user presses “1” “AB9876543CDEF210” should display on 7-seg Display and when user press 2 leds should glow 17 times in a loop. If any other key is pressed no action should be taken Rubrics: Analytic Approach (50%) Syntax (25%) Desired output (25%)
The loop instructions transfer execution control to another point designated by the instruction pointer. (ip) O (ecx) + sign extended 8-bit displacement (ip) + sign extended 8-bit displacement O (ip) + unsigned 8-bit displacement O (ecx) + unsigned 8-bit displacement
microprossor Q3/(A) Write an ALP to evaluate x(y - z) where x = 50H, y = 60H and z = 80H and store the result in a memory location 540O0H.
2. Combinational circuits: Y = (A B) + (A C). B a) Refer to the equation above, draw a combinational logic circuit that implements this function. b) Draw a truth table for the 2(a) circuits. c) Write a sum-of-products representation of Y. d) Write a product-of-sums representation of Y. e) Write the Assembly language code for the equation above using instruction 2-address and instruction 3-address.