A rod with a cross-sectional area of A and loaded in tension with an axial force of P = 2000 lbf undergoes a stress of o = P/A. Using a material strength of 24 kpsi and a design factor of 3.0, determine the minimum diameter of a solid circular rod.
Q: A spherical gas-storage tank with an inside diameter of 12 m is being constructed to store gas under…
A:
Q: The pipe assembly shown is subjected to a force F = 7 kN and P = 14 kN. It is made of steel with Sy…
A:
Q: Select the lightest W shape that will act as a column of 7 m long with both end hinged and support…
A:
Q: 100 D P= 400 kN 5. A hollow steel tube with an inside diameter of 100 mm must carry a tensile load…
A:
Q: A gap of 0.02 in. exists between the composite rod and the wall when the temperature is 75°F. NOTE:…
A: Given data: ◆ The properties of an aluminum: Thermal Expansion coefficient: αAl = 12.9 × 10-6 /°F…
Q: A 150-mm diameter shaft supports a load of 12 kN. The shaft runs in a bearing whose length is 1.5…
A:
Q: A storage tank is 5 m in diameter, 4 m high and the density of the fluid it contains is 795 kg/m3.…
A:
Q: The compression load of 120 kN acts on the steel pipe of Table B-14. Determine the minimum Nominal…
A: Compressive load =120kN Factor of safety =1.5 Yield strength =240 MPa Let diameter be "d"
Q: Determine the changes in length, breadth and thickness of a steel bar which is 4 m long, 30 mm wide…
A:
Q: Three parallel vertical rods of equal length (L-2m) support a rigid beam AB to which a force…
A: Given dataLength of the rods L = 2mTransvers load acting on the rigid beam P = 40kNProperties of…
Q: A thin-walled pressure vessel with an outer diameter of 0.6m and a material thickness of t= 6mm is…
A: Please find the answer below
Q: An open belt drive connected two parallel shafts 1.2 m apart. The driving and driven shafts rotate…
A: Here Given that L=1.2m= distance between driving pulley and driven pulley N1=350 rpm= rotational…
Q: Q A cylindrical pressure vessel has an inner diameter of 1.5 m and a thickness of 12 mm. Determine…
A: Given data:
Q: A thick cylinder is built up by shrinking an aluminium tube 20mm thick upon a hollow aluminium…
A:
Q: A stepped circular bar having diameters of 20 mm, 15 mm, and 10 mm over axial lengths of 100 mm, 80…
A:
Q: 1. A solid bar of circular cross section has a diameter of 40mm and length of 1300mm. G=80GPa and…
A: This question is related with the pure torsion equation.
Q: A bar with a rectangular cross section is connected to a support bracket with a circular pin as…
A: Find the maximum allowable load
Q: A bar with a rectangular cross section is connected to a support bracket with a circular pin. The…
A:
Q: A 3.2-meter-long fixed and hollow cast iron column has its internal and external diameters as 60 mm…
A: Given Data The length of the column is: L=3.2 m Internal diameter of the column is: di=60 mm=0.06 m…
Q: A coiled spring with 5 cm of outside diameter is required to work under the load of 190 N. The wire…
A: Given data: NA=6 Need to determine the total number of coils in the spring.
Q: Determine the diameter of a circular rod made of ductile material with a fatigue strength (complete…
A:
Q: The principal stresses at a point inside a solid object are ơ1 = 100 MPa, 02= 100 MPa and 03= 0 MPa.…
A:
Q: A thrust collar that rests on a 0.95 in. thick polymer plate supports the vertical nylon shaft. The…
A:
Q: The 10-mm-diameter steel bolt is surrounded by a bronze sleeve in (Figure1). The outer diameter of…
A: givendiameter of steel bolt ds=10mmouter diameter of this sleeve is dc=20mminner diameter of this…
Q: A steel bar is placed between two copper bars, each having the same area and length as steel bar at…
A: Given that: T1 = 20 oC T2 = 320 oC dL = 1.5 mm It is required to determine the original length of…
Q: A soccer ball with an inside diameter of 118 mm is inflated to a gage pressure of 110 kPa. The ball…
A: Given Pressure, P = 110 kPa Factor of safety, f = 3 Yield strength, Y = 25…
Q: 1. A rod will be selected to support a tensile load of 74 kN. If the allowable tensile stress of the…
A: It is required to choose correct option
Q: The uniform 3830 kg bar is supported by a smooth wall at A and by a pin at B that is in double…
A: givenuniform bar mass m=3830kgdouble shear working shear stress is σw=74 MPag=9.81m/s2LAB=10mL1=6m
Q: A spherical gas-storage tank with an inside diameter of 26 ft is being constructed to store gas…
A: Given data: Geometry of tank : SphericalInside diameter of tank = d = 26 ft = 26 x 12 = 312 inGas…
Q: Situation 2 -A steel column of hollow circular cross section is supported on a circular steel base…
A:
Q: A spherical gas-storage tank with an inside diameter of 32 ft is being constructed to store gas…
A:
Q: A pressure vessel has an internal diameter of 1 m and is to be subjected to an internal pressure of…
A:
Q: 1. A 60-mm diameter steel tube with a wall thickness of 3 mm just fits in a rigid hole. Determine…
A:
Q: PROBLEM NO. 4 In Fig. 4, determine the normal stress and change in length of the aluminum rod if the…
A:
Q: Determine the diameter of a tensile member of a circular cross-section. The following data is given…
A:
Q: 1. A piston rod of an air-operated press is to exert a maximum force of 20 kN. During the…
A: given; maximum force(F)=20KNcylinder pressure (P)=700KPalenth of piston rod (L)=760mm=0.76m
Q: A spherical gas-storage tank with inside diameter, d = 6.5 (m) is being constructed to store gas…
A: Given data Diameter of spherical tank = d = 6.5 mInternal pressure = 1.9 MPaYield strength of…
Q: A steam boiler, 1.2 meter in diameter, generates steam at a gauge pressure of 0.7 N/mm2. Assuming…
A:
Q: A spherical gas tank has an inner radius of r = 1.5m, if it subjected to an internal pressure of p =…
A: r=1.5m Ap=300kPa
Q: Rods AC and BD are В A made of the same material and are A4c = A35 = 0.5 in.? E 4c = E3D = 10.6x10°…
A: Given: the load acting on member CD, P = 1 kip The length of rods, L = 4 ft The area of the rods, A…
Q: a short hollow cylindrical steel compression member is required to support an axial load of 180 kN.…
A:
Q: The internal pressure of a 400 mm inside diameter cylindrical tank is 10 MPa and the wall thickness…
A:
Q: A 12cm x 16cm air compressor is operated with a maximum pressure of 10 kg/cm2. There are5 bolts with…
A: Givendi=12cmdo=16cmP=10kg/cm2n=5σy=64ksi
Q: A steel [E = 200 GPa] rod with a circular cross section is 8-m long. Determine the minimum diameter…
A:
Q: 20 ksi 40 ksi 60 ksi The differential element above represents the state of plane stress at a point…
A: Stress is defined as the force per unit area of the surface. There are two types of stresses in…
Q: The d = 12-mm-diameter solid rod passes through a D = 17-mm-diameter hole in the support plate. When…
A:
Q: Determine the outside diameter of a hollow steel rod that will carry a tensile load of 55,000 kg at…
A: Giventensile load P=55000kgstress σ=1500kg/cm2thickness t=10mm=1cm
Trending now
This is a popular solution!
Step by step
Solved in 2 steps
- A spherical balloon is filled with a gas. The outer diameter of the balloon is 20 in. and the thickness is 0,012 in. Calculate the maximum permissible pressure in the balloon if the allowable tensile stress and the allowable shear stress in the balloon are 1 ksi and 0.3 ksi, respectively.An elevated jogging track is supported at intervals by a wood beam AB (L = 7.5 ft) that is pinned at A and supported by steel rod BC and a steel washer at B. Both the rod (dBC= 3/16 in.) and the washer (dB= 1.0 in.) were designed using a rod tension force of TBC=415 lb. The rod was sized using a factor of safely of 3 against reaching the ultimate stress tru— 60 ksi. An allowable bearing stress sba= 565 psi was used to size the washer at B. A small platform HF is suspended below a section of the elevated track to support some mechanical and electrical equipment. The equipment load is uniform load q = 50 lb/ft and concentrated load WE= 175 lb at mid-span of beam HF. The plan is to drill a hole through beam ABaX £land install the same rod (dBC) and washer) dB) at both D and F to support beam HF. (a) Use s and to check the proposed design for rod DF and washer d,: are they acceptable? (b) Re-check the normal tensile stress in rod BC and bearing stress at 8 if either is inadequate under the additional load from platform HF. Re-design them to meet the original design criteria.-27 A square plate with side dimension of 2 in. is subjected to compressive stress a and tensile stress The stresses on element A oriented at angle ?? x1=45° aresy1= 75 psi. tx1y1= 275 psi. . Find the state of stress on the element lilt is rotated clockwise to align the x3 axis with the horizontal x axis.
- Solve the preceding problem if the internal pressure is 3,85 MPa, the diameter is 20 m, the yield stress is 590 MPa, and the factor of safety is 3.0. (a) Determine the required thickness to the nearest millimeter. (b) If the tank wall thickness is 85 mm, what is the maximum permissible internal pressure?-26 A rectangular plate of dimensions 125 mm × 75 mm is subjected to tensile stress sy= 67 kPa and compressive stress a. If it is known that the normal stress along the diagonal t—t is ??t= -6.57 kPa, find stress ??y on element A. aThe hollow drill pipe for an oil well (sec figure) is 6,2 in. in outer diameter and 0.75 in. in thickness. Just above the bit, the compressive force in the pipe (due to the weight of the pipe) is 62 kips and the torque (due to drilling) is 185 kip-in. Determine the maximum tensile, compressive, and shear stresses in the drill pipe.
- A pressurized circular cylinder has a sealed cover plate fastened with steel bolts (see figure). The pressure P of the gas in the cylinder is290psi, the inside diameter D of the cylinder is 10.0 in., and the diameter dBof the bolts is 0.50 in. I f the allowable tensile stress in the bolts is 10,000 psi, find the number n of bolts needed to fasten the cover.A wine of length L = 4 ft and diameter d = 0.125 in. is stretched by tensile forces P = 600 lb. The wire is made of a copper alloy having a stress-strain relationship that may be described mathematically by =18,0001+30000.03(=ksi) in which is nondimensional and has units of kips per square inch (ksi). (a) Construct a stress-strain diagram for the material. (bj Determine the elongation, of the wire due to the Forces P. (c) IF the forces are removed, what is the permanent set of the bar? (d) If the forces are applied again, what is the proportional limit?Solve the preceding problem if F =90 mm, F = 42 kN, and t = 40°MPa
- An aluminum bar has length L = 6 ft and diameter d = 1.375 in. The stress-strain curse for the aluminum is shown in Fig. 1.34. The initial straight, line part of the curve has a slope (modulus of elasticity) of 10.6 × 106 psi. The bar is loaded by tensile forces P = 44.6 k and then unloaded. (a) That is the permanent set of the bar? (b) If the bar is reloaded. what is the proportional limit? hint: Use the concepts illustrated in Figs. l.39b and 1.40.A capped cast-iron pipe is compressed by a brass rod, as shown. The mil is turned until it is just snug, then add an additional quarter turn to pre-compress the cast-iron pipe. The pitch of the threads of the bolt ap = 52 mils (a mil is one-thousandth of an inch). Use the numerical properties provided. (a) What stresses a and arwill be produced in the cast-iron pipe and brass rod. respectively, by the additional quarter turn of the nut? (b) Find the bearing stress ahbeneath the washer and the shear stress t(in the steel cap.The rails of a railroad track are welded together at their ends (to form continuous rails and thus eliminate the clacking sound of the wheels) when the temperature is 60°F. What compressive stress ?? =6.5×10-6 /? is produced in the rails when they are heated by the sun to 120"F if the coefficient of thermal expansion a = the modulus of elasticity E = 30 × 106 psi?