A rope connecting two blocks passes around a fric-The coeffi-tionless pulley and a fixed drum (Fig.cient of friction between the rope and the drum and be-tween the 10-kg block and the wall is 0.30; the pinsupporting the 30-kg block is frictionless. Determine themaximum force P for which no motion occurs.0.2 mP+30 kg0.6 m0.2 m-Im-10 kg100 N

Given: The mass of the block supported by the pin m1 is 30 kg. The mass of the block supported by…

Answered: A rope connecting two blocks passes…

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

Question Bank - Friction The two homogeneous bars AB and BC are connected with a pin at B and placed between rough vertical walls. If the coefficient of static friction between each bar and the wall is 0.4, determine the largest angle 0 for which the assembly will remain at rest. 600 mm 6N 600 mm 8 N A. Technology Druen by fanoation Tips: 6N force and 8N force are acting vertically by gravity at the center of the material. Expose the forces acting between the bars and the wall (F and N) Check which interaction will first impend sliding - then expose if free body diagram from the internal hinge at B. e =? Answer in ° (1-2 Decimals are accepted)
The thin plate ABCD of mass 8 kg is held in the position shown by the wire BH and two links AE and DF. Neglecting the mass of the links, determine immediately after wire BH has been cut (a) the acceleration of the plate, (b) the force in each link. H. E 150 mm 30% A B F 200 mm 30 D. IC 500 mm
The frame given in the figureR = 0.25m radius at point Ea frictionless reelare available. Support reactions andall joint forcescalculate. (W = 200 kN)
Q2. Replace the loading acting on the beam with a single resultant force. Determine (a) the force magnitude, F. (b) the horizontal angle of the force, 0. (c) how far the force should be placed from point A on the beam, x. A 60° |--2 -2 m 450 N 4 m 300 N B -3 m 700 N 30° 3000 N·m
Three pulleys are joined by solid steel shafts AB and BC. If G = 200 GPa, determine the unit shearing stress in shafts BC. In MPa A 25 mm ara B 450 N-m 1.2 m 1300N-m 38 mm dia 1.80 m 900 N-m
Problem I A 2.25-kg slender rod AB and a 1.85-kg slender rod BC are connected by a pin at B and by the cord AC. The assembly designed by engineers can rotate in a vertical plane under the combined effect of gravity and a couple M applied to rod BC. Knowing that in the position shown, the 300 mm angular velocity of the assembly is zero and the tension in cord AC is equal to 25.0 N, determine; A (a) the angular acceleration of the assembly (b) the magnitude of the couple, M 400 mm C 400 mm AM B
5- Replace the forces acting on the plate by a wrench. Specify the force and couple moment for the wrench and the point P(x, y) where its line of action intersects the plate. F, = |-300k) N %3D Fe= [200j| N 2m 500N 30 F = (4001) N
Question 2 Frame ABCDE shown in Figure Q2 is supported by a fixed connection at B, roller at D and pinned at A. The frame carries 200 kN horizontal point load acting at the middle of member AC, 50 kN point load at point E and 50 kN/m uniform distributed load on member BC. El is constant. majum (b) 2m 2 m 50 kN/m 200 kN 6 m Figure Q2: Frame [Rajah Q2: Kerangka] 6 m D Next, calculate the fixed-end moment (FEM) for all members. w 1000 50 kN (a) For the case of no sway, calculate the value of stiffness (K) and distribution factor (DF) for each member. 2 m
■ Determine the maximum tension force T for the three cases in the figure. ■ Consider only the resistance from the angle. 100 myn 5275 tomm TEM 10mm I 1/20mm Typical хот tom томил Вотик Вэтаа Somm T T
An 800 N-m couple is applied to the flywheel asshown. The coefficient of belt friction is 0.20. Theminimum force P required to prevent rotation of theflywheel is applied.a.) Which Tension is larger, TA or TB? Explainb.) What is the angle of contact in radians?c.) What is the value of the ratio TA/TB?
Isosceles triangular gate AB, as shown in the figure, is hinged at A. The horizontal force (P) is required at point B for equilibrium. The weight of the gate is negligible, and C 2 m J- 4 m E- 1.2 m 9- 60° S.G. of Oil 0.82 Oil, SG = 0.82 Gate DI
A thin and weightless beam is supported by a pin connection at A and by a roller at B (see figure 2.1). A load of 10 N is applied at the extremity C, at an angle of 45 degrees. A vertical load of 15 N is applied at point D, between 1 and B. (a) Assign a value to the length AD and calculate the reaction forces at A and B. (b) If you had to replace the pin connection and the roller support with only one support, what support would you use, and where, to keep the beam in equilibrium? Justify your suggestion(s). 15 N D 9m Figure 2.1 B 10 N 45° 3 m C

SEE MORE QUESTIONS

Recommended textbooks for you

Structural Analysis

Civil Engineering

ISBN:

9781337630931

Author:

KASSIMALI, Aslam.

Publisher:

Cengage,

Structural Analysis (10th Edition)

Civil Engineering

ISBN:

9780134610672

Author:

Russell C. Hibbeler

Publisher:

PEARSON

Principles of Foundation Engineering (MindTap Cou…

Civil Engineering

ISBN:

9781337705028

Author:

Braja M. Das, Nagaratnam Sivakugan

Publisher:

Cengage Learning

Structural Analysis

Civil Engineering

ISBN:

9781337630931

Author:

KASSIMALI, Aslam.

Publisher:

Cengage,

Structural Analysis (10th Edition)

Civil Engineering

ISBN:

9780134610672

Author:

Russell C. Hibbeler

Publisher:

PEARSON

Principles of Foundation Engineering (MindTap Cou…

Civil Engineering

ISBN:

9781337705028

Author:

Braja M. Das, Nagaratnam Sivakugan

Publisher:

Cengage Learning

Fundamentals of Structural Analysis

Civil Engineering

ISBN:

9780073398006

Author:

Kenneth M. Leet Emeritus, Chia-Ming Uang, Joel Lanning

Publisher:

McGraw-Hill Education

Sustainable Energy

Civil Engineering

ISBN:

9781337551663

Author:

DUNLAP, Richard A.

Publisher:

Cengage,

Traffic and Highway Engineering

Civil Engineering

ISBN:

9781305156241

Author:

Garber, Nicholas J.

Publisher:

Cengage Learning

SEE MORE TEXTBOOKS