A shaft with 15 mm diameter is fixed as shown below. The shaft is made from AISI 1006 cold drawn steel (280 MPa). The (a) Draw the stress elements at point A (top of shaft) and B (side of shaft), indicating the magnitude and directions of the stresses. applied loading is as follows: F = 0.55 kN, P = 4 kN, T = 25 Nm. (b) Find the safety factor at point A and B using both MSS and DE theory. -100 mm A 15-mm D.

A shaft with 15 mm diameter is fixed as shown below. The shaft is made from AISI 1006 cold drawn steel (280 MPa). The (a) Draw the stress elements at point A (top of shaft) and B (side of shaft), indicating the magnitude and directions of the stresses. applied loading is as follows: F = 0.55 kN, P = 4 kN, T = 25 Nm. (b) Find the safety factor at point A and B using both MSS and DE theory. -100 mm A 15-mm D.

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

The rectangular bar shown is connected to a support bracket with a 16 mm diameter pin. The width of the rectangular bar is 60 mm and its thickness is 25 mm. The bearing stress in the bar cannot exceed 200 MPa. Determine the maximum value of Pmax that can be supported based solely on consideration of the bearing stress in the bar. Note: This question is not asking about any stresses in the support bracket.just bearing stress in the rectangular bar. Rectangular bar Support bracket
Problem 5-82 The Am1004-T61 magnesium tube is bonded to the A-36 steel rod. If a torque of T = 5 kN m is applied to end A, determine the maximum shear stress in each material. Sketch the shear stress distribution. 900 mm B 80 mm, 40 mm
Determine the maximum force P that can be applied to the specimen. The bar is made from steel and has an allowable stress of 150 MPa. 2R = 5mm R = 20mm- PP 150mm -6mm
The light rigid bar ABCD shown below is pinned at B and connected to two vertical rods. Assuming that the bar was initially horizontal and the rods stress-free, determine the stress in each rod after the load P = 20 kN is applied. steel L=1.5 m A=300 mm2 2 m- E= 200 GPa B D Aluminun L=2 m P = 20 kN - 1m A= 500 mm2 E= 70 GPa
A steel tube is rigidly attached between an Al rod and a bronze rod. Axial loads are applied at the positions indicated. Find the maximum value of P that will not exceed a stress of 80MPa in Al, 150MPa in steel and 100 Mpa in bronze. -1.0m 200 mm² 2.0m Steel 400 mm² 2P -2.5 m Bronze 500 mm²
Two cylindrical rods AB and BC are welded together at B and loaded as shown. Knowing that the average normal stress must not exceed 175 MPa in rod AB and 150 MPa in rod BC, determine the smallest allowable values of d1 and d2. 300 mm 250 mm A B C -d₁ 40 kN -d₂. 30 kN
Given the compound bar below, determine the maximum allowable value of P if the change in length of the bar is limited to 5.67mm. The bar properties and allowable stresses are given in the table below. (answer in N)
The general stress element shown is loaded such that o = 20 MPa, oy = -20 MPa, Txy = 10 MPa. What is the max dy 1 xy 70x
The rigid bar AB is hinged at A and supported by a steel plate hanger. The hanger is fixed at C and bolted at D with two plates. D Given: Width of plate hanger = 40 mm Thickness od plate hanger = 10 mm Bolt diameter = 20 mm 2 m 1.2 m B Allowable bolt shear stress = 60 MPa Allowable bolt bearing stress = 250 MPa W a. What is the allowable stress in the hanger based on bolt capacity in double shear at D. b. If the maximum tensile stress in the hanger is 130MPA, find the allowable load W c. If the load W= 60KN, find the vertical displacement at B.
The material used for the shaft has an allowable shear stress of tallow= 40 MPa. If the members are connected together with a fillet weld of radius r= 2.25 mm, determine the maximum torque T that can be applied. Where will the largest stress occur? 30 mm 30 mm 15 mm T T T Figure 6
A steel pipe is subjected to the 16-kN load shown below. Its outside diameter is 140 mm and its thickness is 7 mm. Consider that the yield strength of steel is 240 MPa. Analyze point H ONLY. Due to the pressure in the pipe, there is an 11.25-MPa (T) normal stress along x and a 22.50-MPa (T) normal stress along z of point H. A. Determine the internal forces and moments at the pertinent section through an FBD. B. Determine the stresses experienced by point H. Illustrate using a stress element. C. Determine the FS by MSST at point H D. Determine the von Mises equivalent stress at point H E. Determine the FS by MDET at point H 700 mm 16 KN 1,300 mm
2. The bronze bar 3 m long with a cross-sectional area of 350mm2 is placed between two rigid walls. At a temperature of -20 oC, there is a gap of 2.2 mm. Find the temperature atwhich the compressive stress in the bar will be 30 MPa ifthe bar will experience:a. No tensile.b. With an tensile of 5,000 N.Use α = 18.0 x 10-6 /oC and E = 80 GPa.