A sheet of water of uniform thickness (h = 0.02 m) flows from the device shown in the figure below. The water enters vertically through the inlet pipe and exits horizontally with a speed that varies linearly from 0 to 8 m/s along the 0.2-m length of the slit. Determine the y component of anchoring force necessary to hold this device stationary. 0 m/s- FAY= i 0.2m 0.02m N .8m

A sheet of water of uniform thickness (h = 0.02 m) flows from the device shown in the figure below. The water enters vertically through the inlet pipe and exits horizontally with a speed that varies linearly from 0 to 8 m/s along the 0.2-m length of the slit. Determine the y component of anchoring force necessary to hold this device stationary. 0 m/s- FAY= i 0.2m 0.02m N .8m

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Water flows at a rate of 3 m3/s through a 300 mm diameter pipe in which there is a 90o bend. if the pressure at the entrance to the bend is 450 kN/m2 (absolute), determine the total force necessary to anchor (kN) the bend. Friction losses can be neglected.
AVA cir Water is flowing through a horizontal pipe of diameter 200 mm at a velocity of 3 m/s. A circular solid plate of diameter 150 mm is placed in the pipe to obstruct the flow. Find the loss of head due to obstruction in the pipe if C = 0.62.
A piston 46mm in diameter slides concentrically in a fixed cylinder 50mm in diameter. The cylinder is filled with water and when the piston moves into the annular gap, water flows through the annular gap surrounding the piston. If the velocity of piston is 75mm/s raletive to the cylinder, determine the velocity of flow through the gap.
Water flows into the horizontal bend fitting at A with a velocity of V = 6 m/s, and exits at B into the atmosphere as shown in (Figure 1). A 150 mm 200 mm 400 mm y 30° B Determine the a-component of force at C needed to hold the fitting in place. Express your answer to three significant figures and include the appropriate units. Determine the y-component of force at C needed to hold the fitting in place. Express your answer to three significant figures and include the appropriate units.
Water flows through the elbow with a velocity of 4 m/s, as shown in . The pressure within the pipe at A and B is 220 kPa The flow occurs in the horizontal planc. Assume thero is no support at A and B. m/s 75 mm 75 mm 60 45 Part A Determine the a component of force the support at C exerts on the elbow. Express your answer to three significant figures and include the appropriate units.
Neglecting head losses, determinewhat horsepower the pump must deliver toproduce the flow as shown. Here theelevations at points A, B, C, and D are 110 ft.200 ft, 110 ft and 90 ft, respectively. The nozzle area is 0.10 ft2
A horizontal nozzle discharges water into the atmosphere as shown in the figure, being the relative pressure at point 1 equal to p1 = 20 kPa A Pitot tube connected to a mercury manometer is inserted into the flow in area section A1 indicating a height difference h = 0.02 m. For this reading indicated in the Pitot tube, determine the speed in the Area A1 section of the nozzle. For docking block sizing it is necessary to determine the force that the nozzle applies to the fluid. Calculate the component of this force in the x direction. Data: D1 = 0,075 m; D2 = 0,055 m; θ = 30° ; dHg = 13,6.
Oil flows from a tank through 150 m of 150 mm diameter pipe andthen discharges into air as shown. If the head loss from point 1to point 2 is 600 mm, determine the pressure needed at point 1 tocause 17 L/s of oil to flow.
Water flows from a nozzle with a speed of V = 10m/s Stream diameter = 0.1 m Nozzle -- Moving control volume and is collected in a container that moves toward the V = 10 m/s nozzle with a speed of Vcy = 2 m/s as shown in the figure. If the water between the nozzle and the tank is in the constant diameter stream, what is the accumu- V = 2 m/s 3 m lation rate of water in the tank?
The diameter of the pipe at point B is larger than at point A. - At which point is the water speed greater? Point B Point A It is the same at both points. Cannot be determined from the information given.
Water flows into the horizontal bend fitting at A with a velocity of V = 4.2 m/s, and exits at B into the atmosphere as shown in . A 150 mm 200 mm 400 mm 30 Part A Determine the r-component of force at C needed to hold the fitting in place. Express your answer to three significant figures and include the appropriate units.
If a turbulent water flows inside the piping system, the vertical distance h=30 mm, what is the velocity m/s of water at section A. Given that the area of A=3.1 A. A EGL HGL h