A simplified diagram of a racing cars suspension and wheel is used to design the bars and pins. The force that the suspension must withstand can be considered to be a vertical force, F = 1.5 kN, acting vertically upwards at B. Calculate the minimum radius of the bars AB and BC if the maximum allowable stress oalow= 80 MPa. Also, calculate the minimum radius of the pin at A if this pin is in Double Shear and the maximum allowable shear stress Tallow = 50 MPa

A simplified diagram of a racing cars suspension and wheel is used to design the bars and pins. The force that the suspension must withstand can be considered to be a vertical force, F = 1.5 kN, acting vertically upwards at B. Calculate the minimum radius of the bars AB and BC if the maximum allowable stress oalow= 80 MPa. Also, calculate the minimum radius of the pin at A if this pin is in Double Shear and the maximum allowable shear stress Tallow = 50 MPa

International Edition---engineering Mechanics: Statics, 4th Edition

4th Edition

ISBN:9781305501607

Author:Andrew Pytel And Jaan Kiusalaas

Publisher:Andrew Pytel And Jaan Kiusalaas

Chapter4: Coplanar Equilibrium Analysis

Section: Chapter Questions

Problem 4.97P: The figure shows a wire cutter. Determine the cutting force on the wire at A when the 75-N forces...

See similar textbooks

Similar questions

The figure shows a wire cutter. Determine the cutting force on the wire at A when the 75-N forces are applied to the handgrips. (Hint: The horizontal components of pin forces at B and D are zero due to symmetry.)
The linkage shown is used in a vehicle suspension system. Find the forces indicated below when a static force of F = 820 lb is applied to the tire at point C at an angle of 0 = 22° as shown. Assume the connection of the wheel to member AB is rigid. hs hy hi F BY NC SA W4. W, Ws 2013 Michael Swanbom Values for dimensions on the figure are given in the following table. Note the figure may not be to scale. Variable Value Variable Value hi 10 in Wi 8.8 in h2 15.6 in W2 5.6 in h3 18.1 in W3 10.8 in h4 10.9 in WĄ 7.4 in h5 4.9 in W5 9.3 in For all answers, take x as positive to the right and y as positive upward. At point B, member AB exerts a force of B = j lbs on member BHE. At point A, member AD exerts a force of A + j lbs on member AB. At point H, shock GH exerts a force of H = i + i lbs on member ВНЕ. At point E, the magnitude of the force exerted on the car body by member BHE is lbs. At point D, the magnitude of the force exerted on the car body by member AD is lbs. At point G, the…
plz help before -ront The shaft is supported at its ends by two bearings A and B and is subjected to the forces applied to the pulleys fixed to the shaft. (Figure 1) The T₁ 410-N forces act in the - direction and the 200-N and 80-N forces act in the +y direction. The journal bearings at A and B exert only y and components of force on the shaft. Figure lashel but sol is 300 mm A 200 mm 2 150 mm 150 mm ✓ 200 mm 400 mm B. 200 N 200 N 80 N 80 N 1 of 1 ▾ Part B Determine the resultant shear force in the y direction on the cross section at C Express your answer to three significant figures and include appropriate units. (Vc)y=245.714 Submit Part C Submit * Incorrect; Try Again; 3 attempts remaining Check your signs. (Vc),= 175 ▾ Part D Determine the resultant shear force in the direction on the cross section at C. Express your answer to three significant figures and include appropriate unite. T= 10 ▾ Part E Previous Answere (Mc) Submit M ^ Part Fi * Incorrect; Try Again; 5 attempts remaining…
with the following modifications: Add an additional force P = 20kN acting downwards at point B
The cable carrying three 400-N loads has a sag at C of hC = 14 m. Calculate the following: 26.1 The magnitude of the tensile force in segment AB is Blank 1 N. 26.2 The magnitude of the tensile force in segment BC is Blank 2 N. 26.3 The magnitude of the tensile force in segment CD is Blank 3 N. 26.4 The magnitude of the tensile force in segment DE is Blank 4 N.
In the fig. shown, compute the ff: (11-13) the tension in cable BD 7.5 rt To = (14-15) the components of the support 10 rt At C. Ch Cv = 5 rt 1000 lb 12.5 ft S00 I In the fig. shown, compute the ff: (16-18) the resultant using cosine law (force polygon) 60 R = 35 (19-20) the angle of the R measured CW from the x- axis. 500 lb
Problem: The steel pipe has an inner diameter of 2.75 in and an outer diameter of 3 in. The pipe is fixed to the ground at C, and a wrench is attached to the opposite end. The wrench is subjected to a horizontal force of 20 lb that acts in -z direction. Points A and B are located on the surface of the pipe at the same cross section. Note that A lies directly above the -y axis, and B lies directly above the +z axis. 20 lb 10 in. A B y 12 in. (a) Find the normal and shear stresses at points A and B. (b) Find the principal stresses at points A and B. (c) Show all stresses from parts (a) and (b) on properly oriented elements, relative to the given coordinate system.
A 3D truss is supporting 2 forces F₁ and F₂- F₁ = 1,080 N at and angle alpha = 33 deg. F1 is in the y-plane • F2 = 2,232 N at an angle theta = 43 deg. F2 is in a y'z-plane The dimensions of the truss are: |dae=1.0 m dac=1.0m deo=17m LAB dAc pz Forces ась a Cartesian form of F Vector position from C Moment about Point C Moment about AC axis Vector position from E Moment about Point E Moment about BE axis Moment about EJ axis dGI = 1.7 m F₁ (N) املا قابل Fill this table, write your steps under the table, and make a drawing when requested of the moment found (either vector or scalar) y H F₂ (N) Total Force (N) or Moment (N.m) + Make a drawing + Make a drawing + Make a drawing + Make a drawing + Make a drawing Note: The force and the moment about a point are vectors. The moment about an axis is a scalar value. In the box below, enter the moment of F₁+F₂ made about AC-axis in N as an integer.
Given the Horizontal wood member shown that weights 38 lbs/ft and supports three vertical loads F1 - 200 Lbs, F2= 100 Lbs, F3 = -400 Lbs, and is supported by a Pin at A and a Roller at B, calculate Reaction Ay. A origin k 4' 200# f 4' 100# + 400# 4' t 4' B X
QUESTION 2: For the nose landing gear of an aircraft shown in the figure, calculate the internal forces at the vertical section at point A. -150 mm 20 mm- 60° 300 mm -175 mm 12 kN
A safety valve spring having 9 and 2 coils has the ends squared and ground. The outside diameter of the coil is 115 mm and the wire is 13 mm. It has a free length of 203 mm. The length of which this spring must be initially compressed to hold a boiler pressure of 1.38 MPa on the seat of 32 mm diameter. Modulus of rigidity is taken as G=80GN/m?. Find the force acting on the valve set. Compute the Wahl factor
In the given figure, support A is a roller and support B is a pin support. If P=15 kips, calculate the 1) vertical reaction at A, 2) vertical reaction at B, 3) horizontal reaction at B P 6 kips 6 kips В 6 ft – 3 ft 2 ft ' 2 ft