A Single Area consists of 3generating units (G1/G2/G3) with the following characteristics:G1: 250 MVA rating, R1 = 0.02 pu (on the 250 MVA base), initial output P1 = 200 MW.G2: 350 MVA rating, R2 = 0.015 pu (on the 350 MVA base), initial output P2 = 300 MW.0.03 pu (on the 300 MVA base), initial output P3 = 150 MW.G3: 300 MVA rating, R3=The frequency of the system is 60 Hz.Assuming D = 1 pu on a common base of 1000 MVA, what is the new generation output forG3 for a load increase of 75 MW?Select one:O a. 190.55 MWO b. None of theseO c. 203.38 MWd. 166.01 MW

A Single Area consists of 3 generating units (G1/G2/G3) with the following characteristics: G1: 250 MVA rating, R1 = 0.02 pu (on the 250 MVA base), initial output P1 = 200 MW. G2: 350 MVA rating, R2 = 0.015 pu (on the 350 MVA base), initial output P2 = 300 MW. G3: 300 MVA rating, R3 0.03 pu (on the 300 MVA base), initial output P3 = 150 MW. = The frequency of the system is 60 Hz. Assuming D = 1 pu on a common base of 1000 MVA, what is the new generation output for G3 for a load increase of 75 MW? Select one: O a. 190.55 MW O b. None of these O c. 203.38 MW d. 166.01 MW

A Single Area consists of 3 generating units (G1/G2/G3) with the following characteristics: G1: 250 MVA rating, R1 = 0.02 pu (on the 250 MVA base), initial output P1 = 200 MW. G2: 350 MVA rating, R2 = 0.015 pu (on the 350 MVA base), initial output P2 = 300 MW. G3: 300 MVA rating, R3 0.03 pu (on the 300 MVA base), initial output P3 = 150 MW. = The frequency of the system is 60 Hz. Assuming D = 1 pu on a common base of 1000 MVA, what is the new generation output for G3 for a load increase of 75 MW? Select one: O a. 190.55 MW O b. None of these O c. 203.38 MW d. 166.01 MW

Power System Analysis and Design (MindTap Course List)

6th Edition

ISBN:9781305632134

Author:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Publisher:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Chapter3: Power Transformers

Section: Chapter Questions

Problem 3.30P: Reconsider Problem 3.29. If Va,VbandVc are a negative-sequence set, how would the voltage and...

See similar textbooks

Similar questions

What is the load current for the circuit shown in the figure? Please choose one: a. 9.0 mA b. 7.5 mA c. 3.0 mA D. 6.0 mA
what is the use of DC/DC tension converter DC/DC booster MT3608
Consider a PV Module with 24 solar PV cells with the Size of each 15cm x 10cm are connected in series. Choose the correct statement for the above PV Module. (Assume necessary data) a. The output power is 2.25W and the output current is 0.09A b. The output power is 540W and the output current is 45A c. The output power is 54W and the output current is 2.25A d. The output power is 54W and the output current is 4.5A
1) The term Bi is defined as Select one: O a. Negative change in reference bus power to the power change DPi on bus i O b. All of these 1/Pfi Clear my choice
For Fixed Bias Configuration Solve for Ib, Ic and le. Atleast 2 decimal place. Be mindful of units. Assume Ic is not equal to le. ... 4 RC 15002 RB VCC 20V 90A/A 100k2 Ib=Blank 1 HA Ic=Blank 2mA le=Blank 3 mA Blank 1 Add your answer Blank 2 Add your answer Blank 3 Add your answer
Which of the following statement is true? a. Angle between load voltage and load current in a pure capacitive load is 45 degree. b. Angle between load voltage and load current in a pure capacitive load is is 180 degree. c. Angle between load voltage and load current in a pure capacitive load is is zero. d. Angle between load voltage and load current in a pure capacitive load is is 90 degree.
Damping ratio quettion.
5) For a single phase full wave bridge rectifier with a resistive load if the input voltage is 125 V, 60 Hz with the value of resistance is 20 ohms. Compute the value of rms value of load voltage and average value of load voltage by formulating the equations with all steps (uncontrolled)
The voltage regulation can be equal to zero :when .The t and current is not too highO .The p.f. is leading p.f. for any possible current O .The p.f. is lagging p.f. for rated current O
Question 15 In half wave rectifier with filter, if the capacitance is increased, the ripple factor increases. True False Moving to another question will save this response. ip
QUESTION 2 Given is a voltage regulator with a nominal output voltage Vo=11V. When the load current varies between 0.1A and 5A, the output voltage varies between 10.8V and 11V. - Determine the load regulation in percent, write the answer without the unit.
iii. For fully controlled single phase bridge rectifier with inductive load (load current is continuous) ,supply voltage 220 V(RMS) and a=30° .The mean value of output voltage is : (a) 150.32V (b) 171.52V (c) 120.98V