A sinusoidal voltage Av = 36.0 sin 100t, where Av is in volts and t is in seconds, is applied to a series RLC circuit with L = 150 mH, C = 99.0 µF, and R = 73.0 N. (a) What is the impedance of the circuit? (b) What is the maximum current? A (c) Determine the numerical value for w in the equation i = Imax Sin (wt – 4). rad/s (d) Determine the numerical value for o in the equation i = Imax sin (wt – p). rad

A sinusoidal voltage Av = 36.0 sin 100t, where Av is in volts and t is in seconds, is applied to a series RLC circuit with L = 150 mH, C = 99.0 µF, and R = 73.0 N. (a) What is the impedance of the circuit? (b) What is the maximum current? A (c) Determine the numerical value for w in the equation i = Imax Sin (wt – 4). rad/s (d) Determine the numerical value for o in the equation i = Imax sin (wt – p). rad

University Physics Volume 2

18th Edition

ISBN:9781938168161

Author:OpenStax

Publisher:OpenStax

Chapter15: Alternating-current Circuits

Section: Chapter Questions

Problem 27P: In an RLC series circuit, the voltage amplitude and frequency of the source are 100 V and 500 Hz,...

See similar textbooks

Similar questions

A series RLC circuit has resistance R = 50.0 and inductance L. = 0.500 H. (a) Find the circuits capacitance C if the voltage source operates at a frequency of f = 60.0 Hz and the impedance is Z = R = 50.0 . (b) What is the phase angle between the current and the voltage?
In an RLC series circuit, the voltage amplitude and frequency of the source are 100 V and 500 Hz, respectively, an R = 5O0. L=0.20H, and C=2.0F . (a)What is the impedance of the circuit? (b) What is the amplitude of the current from the source? (C) If the emf of the source Is given by v(tt)=(100V)sin , how does the current vary with time? (d) Repeat the calculations with C changed to 0.20F .
An PLC series circuit with R=600 , L = 30 mH. and c=0.050F is driven by an ac source whose frequency and voltage amplitude are 500 Hz and 50 V, respectively, (a) What is the impedance of the circuit? (b) What is the amplitude of the current in the circuit? (c) What is the phase angle between the emf of the source and the current?
In the AC circuit shown in Figure P32.3, R = 70.0 and the output voltage of the AC source is Vmax sin t. (a) If VR = 0.250 Vmax for the first time at t = 0.0100 s, what is the angular frequency of the source? (b) What is the next value of t for which VR = 0.250 Vmax? Figure P32.6 Problem 3 and 5.
An ac source of voltage amplitude 10 V delivers electric energy at a rate of 0.80 W when its current output is 2.5 A. What is the phase angle between the emf and the current?
Consider the Filter circuit shown in Figure P33.56. (a) Show that the ratio of the amplitude of the output voltage to that of the input voltage is to that of input voltage is VoutVin=1/CR2+(1C)2 (b) What value does this ratio approach as the frequency decreases toward zero? (c) What value does this ratio approach as the frequency increases without limit? (d) At what frequency is the ratio equal to one-half?
In an oscillating RLC circuit, R = 7.0 L. = 10 mH. And C = 3.0 F. Initially, the capacitor has a charge of 8.0 C and the current is zero. Calculate the charge on the capacitor (a) five cycles later and (b) 50 cycles later.
An RLC circuit has resistance R = 225 and inductive reactance XL. = 175 . (a) Calculate the circuits capacitive reactance XC if its power factor is cos = 0.707. Repeat the calculation for (b) cos = 1.00 and (c) cos = 1.00 102.
An inductor and a resistor are connected in series across an AC source as in Figure OQ33.1. Immediately after the switch is closed, which of the following statements is true? (a) The current in the circuit is V/R. (b) The voltage across the inductor is zero, (c) The current in the circuit is zero, (d) The voltage across the resistor is V (e) The voltage across the inductor is half its maximum value.