A small aluminum alloy [E = 79 GPa] tee shape is used as a simply supported beam as shown. For this beam, a = 155 mm. The cross- sectional dimensions of the tee shape are b = 16 mm, d = 24 mm, and t = 8 mm. After loads are applied to the beam at B, C, and D, a compressive normal strain of 410 µe is measured from a strain gage located at c = 9 mm below the topmost edge of the tee stem at section 1-1. What is the applied load P? P | 3P Strain gage- d D E H b

A small aluminum alloy [E = 79 GPa] tee shape is used as a simply supported beam as shown. For this beam, a = 155 mm. The cross- sectional dimensions of the tee shape are b = 16 mm, d = 24 mm, and t = 8 mm. After loads are applied to the beam at B, C, and D, a compressive normal strain of 410 µe is measured from a strain gage located at c = 9 mm below the topmost edge of the tee stem at section 1-1. What is the applied load P? P | 3P Strain gage- d D E H b

Steel Design (Activate Learning with these NEW titles from Engineering!)

6th Edition

ISBN:9781337094740

Author:Segui, William T.

Publisher:Segui, William T.

Chapter1: Introduction

Section: Chapter Questions

Problem 1.5.6P: The data in Table 1.5.3 were obtained from a tensile test of a metal specimen with a rectangular...

See similar textbooks

Similar questions

The data in Table 1.5.3 were obtained from a tensile test of a metal specimen with a rectangular cross section of 0.2011in.2 in area and a gage length (the length over which the elongation is measured) of 2.000 inches. The specimen was not loaded to failure. a. Generate a table of stress and strain values. b. Plot these values and draw a best-fit line to obtain a stress-strain curve. c. Determine the modulus of elasticity from the slope of the linear portion of the curve. d. Estimate the value of the proportional limit. e. Use the 0.2 offset method to determine the yield stress.
A small aluminum alloy [E = 61 GPa] tee shape is used as a simply supported beam as shown. For this beam, a = 155 mm. The cross-sectional dimensions of the tee shape are b %3D = 22 mm, d = 33 mm, and t = 7 mm. After loads are applied to the beam at B, C, and D, a %3D compressive normal strain of 420 µɛ is measured from a strain gage located at c = 6 mm below the topmost edge of the tee stem at section 1-1. What is the applied load P? P 3P В D E Strain gage- d H b Answer: P = i N
A small aluminum alloy [E = 62 GPa] tee shape is used as a simply supported beam as shown. For this beam, a = 220 mm. The cross-sectional dimensions of the tee shape are b = 18 mm, d = 27 mm, and t = 6 mm. After loads are applied to the beam at B, C, and D, a compressive normal strain of 430 με is measured from a strain gage located at c = 6 mm below the topmost edge of the tee stem at section 1-1. What is the applied load P
A small aluminum alloy [E= 77 GPa] tee shape is used as a simply supported beam as shown. For this beam, a = 160 mm. The cross- sectional dimensions of the tee shape are b= 22 mm, d = 33 mm, and t= 4 mm. After loads are applied to the beam at B, C, and D, a compressive normal strain of 410 uɛ is measured from a strain gage located at c = 10 mm below the topmost edge of the tee stem at section 1-1. What is the applied load P? %3D %3D %3D 3P Strain gage E Answer:
A small aluminum alloy [E = 74 GPa] tee shape is used as a simply supported beam as shown. For this beam, a = 130 mm. The cross- sectional dimensions of the tee shape are b = 25 mm, d = 38 mm, and t = 9 mm. After loads are applied to the beam at B, C, and D, a compressive normal strain of 460 µɛ is measured from a strain gage located at c = 5 mm below the topmost edge of the tee stem at section 1-1. What is the applied load P? P 3P Strain gage- d В D E 2 H Answer: P= i N
A small aluminum alloy [E = 65 GPa] tee shape is used as a simply supported beam as shown. For this beam, a = 165 mm. The cross- sectional dimensions of the tee shape are b = 19 mm, d = 29 mm, and t = 7 mm. After loads are applied to the beam at B, C, and D, a compressive normal strain of 480 µɛ is measured from a strain gage located at c = 5 mm below the topmost edge of the tee stem at section 1-1. What is the applied load P? %3D 3P Strain gage d. H. a. b. Answer: i ! N
A small aluminum alloy [E = 65 GPa] tee shape is used as a simply supported beam as shown. For this beam, a = 125 mm. The cross-sectional dimensions of the tee shape are b = 15 mm, d = 23 mm, and t = 9 mm. After loads are applied to the beam at B, C, and D, a compressive normal strain of 460 µɛ is measured from a strain gage located at c = 9 mm below the topmost edge of the tee stem at section 1-1. What is the applied load P? P 3P Strain gage D E H b. Answer: P = i 29254 N
A small aluminum alloy [E = 80 GPa] tee shape is used as a simply supported beam as shown. For this beam, a = 165 mm. The cross- sectional dimensions of the tee shape are b = 19 mm, d = 29 mm, and t = 7 mm. After loads are applied to the beam at B, C, and D, a compressive normal strain of 430 µɛ is measured from a strain gage located at c = 10 mm below the topmost edge of the tee stem at section 1-1. What is the applied load P? P ЗР Strain gage d D E H Answer: P = i
A small aluminum alloy [E = 65 GPa] tee shape is used as a simply supported beam as shown. For this beam, a = 165 mm. The cross- sectional dimensions of the tee shape are b = 19 mm, d = 29 mm, and t = 7 mm. After loads are applied to the beam at B, C, and D, a compressive normal strain of 480 µɛ is measured from a strain gage located at c = 5 mm below the topmost edge of the tee stem at section 1-1. What is the applied load P? P 3P |1 Strain gage- d D E 2 H b Answer: P= i N
A small aluminum alloy [E = 62 GPa] tee shape is used as a simply supported beam as shown. For this beam, a = 175 mm. The cross- sectional dimensions of the tee shape are b = 19 mm, d = 29 mm, and t = 6 mm. After loads are applied to the beam at B, C, and D, a compressive normal strain of 430 µɛ is measured from a strain gage located at c = 9 mm below the topmost edge of the tee stem at section 1-1. What is the applied load P? ЗР Strain gage d C D a H
A small aluminum alloy [E = 71 GPa] tee shape is used as a simply supported beam as shown. For this beam, a = 120 mm. The cross- sectional dimensions of the tee shape are b = 17 mm, d = 26 mm, andt = 6 mm. After loads are applied to the beam at B, C, and D, a compressive normal strain of 460 µɛ is measured from a strain gage located at c = 10 mm below the topmost edge of the tee stem at section 1-1. What is the applied load P? P P ЗР Strain gage C |D H Answer: P = N
A small aluminum alloy [E = 62 GPa] tee shape is used as a simply supported beam as shown. For this beam, a = 155 mm. The cross- sectional dimensions of the tee shape are b = 16 mm, d = 24 mm, and t = 9 mm. After loads are applied to the beam at B, C, and D, a compressive normal strain of 470 µɛ is measured from a strain gage located at c = 9 mm below the topmost edge of the tee stem at section 1-1. What is the applied load P? P 3P Strain gage х B 11 D E a a H b sla