A solar cell having Fill Factor (FF) 68% gives 0.6 V voltage at maximum power point at STC (input power density is 1000 W/m²). The cell gives 3 A short circuit current and 0.7 V open circuit voltage. The area of the solar cell is 50 cm². (i) What is the current at maximum power point of the solar cell? (ii) Calculate the power conversion efficiency of the cell. (iii) Draw the I-V curve of the cell.

A solar cell having Fill Factor (FF) 68% gives 0.6 V voltage at maximum power point at STC (input power density is 1000 W/m²). The cell gives 3 A short circuit current and 0.7 V open circuit voltage. The area of the solar cell is 50 cm². (i) What is the current at maximum power point of the solar cell? (ii) Calculate the power conversion efficiency of the cell. (iii) Draw the I-V curve of the cell.

Delmar's Standard Textbook Of Electricity

7th Edition

ISBN:9781337900348

Author:Stephen L. Herman

Publisher:Stephen L. Herman

Chapter30: Dc Motors

Section: Chapter Questions

Problem 6RQ: What is CEMF?

See similar textbooks

Similar questions

Calculate the equivalent resistances Rin of the following circuits. (The resistance value of the diodes in the conduction will be 0, the resistance value of the diodes in the insulation will be taken as infinity. R1=10ohm
With reference to energy conversion process, write the difference between Solar Power Tower system and Solar Photovoltaic System. Draw the structure of a solar cell and mark the electron flow direction and electric current flow directions
A. Explain the difference between charging current andfaradaic current. B. What is the purpose of waiting 1s after a voltage pulse before measuring current in sampled current voltammetry? C. Why is square wave voltammetry more sensitive than sampled current voltammetry?
b) Figure 3 shows the AC voltmeter that is given to you to make a measurement of 240Vrms from TNB AC supply. However, the voltage range is lower than the voltage of TNB AC supply. By using given AC voltmeter, design the new AC voltmeter circuit to measure the required voltage. Given Sac AC voltmeter meter is 5k2/V. Assume that the meter indicator will deflect 50% of full scale during measurement. V 40 30 20 10 CE 2-151 Figure 3
a) Graphically show the differences between alternating current voltage (A.C) and direct current voltage (D.C). What are the advantages of A.C compared to D.C?
A resistor Ra is in series with a voltage source Va. Draw the circuit. Label the voltage across the combination as v and the current as i. Draw and label the volt–ampere characteristic (i versus v).
The record efficiency for a single crystal silicon photovoltaic solar cell is 26.1%. Describe two methods to engineer PV cells to be more efficient than this and then compare these methods, evaluating if these alternate technologies are commercially viable. If you believe they are commercially viable describe in what situation they would be used.
A half-wave rectifier is needed to supply 15-V dc to a load that draws an average current of 250 mA. The peak-to-peak ripple is required to be 0.2 V or less. What is the minimum value allowed for the smoothing capacitance?
Three condensers of 6, 10, and 15 micro-farads are connected in series across a 200V supply. If the condensers are disconnected, how much energy can the charged condensers provide if connected across each other with like polarities together? Ans. 0.052 J
The graph below illustrates the effect of temperature on the conductivity of an extrinsic semiconductor. Which stage most semiconductor devices can be operated? III II by log, o low high temp. IT temp. Select one: O a. No correct answer given O b. Stage 2 because of the constant behaviour O c. Stage 3 because increasing the temperature increase the conductivity of semiconductor. d. Stage 1 because low temperature increases the conductivity of materials. Question 1 For some applications, gold is used as electrical conductor instead of copper because. Select one: a. all the answers are wrong b. Less density and cheaper than copper С. Easily oxidised and react with other material O d. It has higher conductivity than copper e. Good ductility and high strength
In a rectifier circuit , DC output voltage and RMS output voltage is 0.3 V & 0.49 V respectively. The form factor of this circuit is ___________________. a. 1.63 b. 3.27 c. 0.61 d. 1.17
24 A 6V battery, deliviers loma to three..... resistors in parallel, R₁ = 1kr, R2 = 2 kref=Rx-. Calculate: a) Current in Rx that is Ix. [Ans: I MA). b) Power dissipated. by. R.x. and R... [Anss 6mw, 36 mnd. Resistance ratio Rx/R [Anss: 6/1]- d) Current ratio I/Ix- (Ans: -6-/1]-