A solid shaft of circular cross section has a diameter of 15mm and is loaded by a torque of 130Nm at B and a torque of 560Nm at the free end (C). The material has a modulus of rigidity, G = 80 GPa. Determine the total twist at the free end of the shaft (C) 1.9 rad 550mm B 130Nm 650mm C 560Nm

A solid shaft of circular cross section has a diameter of 15mm and is loaded by a torque of 130Nm at B and a torque of 560Nm at the free end (C). The material has a modulus of rigidity, G = 80 GPa. Determine the total twist at the free end of the shaft (C) 1.9 rad 550mm B 130Nm 650mm C 560Nm

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Related questions

Q: The statements below refer to the main design drivers for the structure of various parts of a…

A: The dynamics of spaceflight are introduced in Spaceflight Dynamics, including orbits, manoeuvres,…

Q: 6. In the crystalline lattice of iron (bcc lattice) the concentration of vacancies is 0,1%. What is…

A: Given: In BCC lattice, the concentration of vacancies = 0, 1% To Find: The relative number n of…

Q: The collar has a mass of 2 kg and is attached to the light spring, which has a stiffness of 30 N∕m…

Q: Problem 7.56 If the system is rotating clockwise with the angular speed @ = 10 rad/s in the position…

A: Given: Angular speed of the system: →ωb=10 rad/s Length of the each bar is L. If the mass of the…

Q: Q/ Evaluate the following integrals. TC 2 √In ²7²7 e* sin(e) dx

Q: Kerosene is placed inside a glass capillary tube having a radius of 0.5 mm. The kerosene inside the…

A: Given data: Radius of capillary tube = R = 0.5 mm = 0.0005 m Standing height = h = 59 mm = 0.059 m…

Q: The U shape shown has dimensions of b-390 mm, d=195 mm, t - 24 mm, and tw 18 mm. A vertical shear…

Q: Question 3 A column of 7 m effective length is to be made by welding two 228 x 12 mm plates to a…

A: Given: The length of column, Le = 7 m The elastic modulus, E = 200 GPa The moment of inertia about…

Q: Figure 4 shows a simply supported timber beam AB with 4.5 m long carrying the uniformly distributed…

Q: a) In the situation illustrated above the mass m₁ is at rest initially. Show that the maximum…

Q: can you aswer part b and please accept the mass on the right (2m) as 2.5kg , the one on the left…

Q: 1. The moment of force F about point O is defined as M₂ = a. rx F b. Fx r c. r. F d. r* F Moment…

A: Given: r = position from point to any point on the line of action of force F F = Applied force We…

Q: A built up wooden beam is made up of two 50 mm by 150 mm sections glued on the lower sides of a 100…

A: Given data: ◆ The built-up beam is made up of following cross-sections: b1 × d1 = 100 mm × 250 mm b2…

Q: Water is flowing in a long cylindrical tube at a mass flowrate of 0.01 kg/s. If the tube diameter is…

Q: For the planar mechanism of figure below, link 4 serves as slider support which is free to rotate…

A: given data-Angular velocity ∆ω=250 rpmtime ∆t=5 sec

Q: Kerosene is placed inside a glass capillary tube having a radius of 0.5 mm. The kerosene inside the…

A: Given data as per question Standing height of kerosene=59 mmdiameter of capillary tube, r=0.5…

Q: Water at 25° is flowing between A and B through a steel pipe 30 centimeters in diameter and a length…

A: According to Bernoulli's equation is based on the principle of conservation of energy head i.e.,…

Q: s constructed from three boards bolted together as shown in Fig. Determine the m shear stress if the…

A: Given data: Shear Force V=35 kN Spacing between each of the bolt is s=250 mm

Q: Ø.495-.500 8.00

Q: b. Assume the robot has a mass M. If it needs to travel 1 km in 30 minutes whilst picking up rubbish…

Q: 3m 3 m² 1.5 2.5 m 2 m

Q: Explain the words "multidimensional" and "parallel" by giving an example of each.

Q: QUESTION FIVE: (a) State the purpose of conducting a Morse test on an internal combustion,…

A: a) Purpose of conducting Morse Test on an Internal Combustion, reciprocating piston engine are as…

Q: Determine the magnitudes of F₁, F2, and F3 for equilibrium of the particle. 5 kN F3 30% 40° 25 F₁ 9…

A: Given data: P1=5 kNP2=9 kN Need to determine the magnitude of the forces F1,F2,F3.

Q: In vibration testing, an instrumented hammer is often used to hit a device to excite it and to…

A: Given data: M=1 Kg c=5Kg/s K=100KN/m

Q: Problem 1. Concentrated load P, at B and difference AT(x) are applied to circular bar with Young's…

A: Given Data- concentrated load =P∘ temp: difference =∆T young's modulus =E diameter at point A=d1=d…

Q: 1. All form tolerances are surface controls except for (Select two correct answers) Straightness of…

A: Ans: Option first and fourth are correct. Straightness of a median line Flatness of a median plane…

Q: Rods (1) and (2) were supposed to fit exactly between the rigid walls at A and C, as indicated in…

A: Given DataE1=74 GPaA=1749 mm2L=738 mmE2=204 GPa

Q: An Insulated rigid tank containing 0.25 m3 of air at 50 oC and 1.5 Bar. If a paddle wheel with a…

Q: Problem 6 For the structure shown in the figure, determine the normal and shear stresses at point A…

Q: A heat pump is a device that transfer thermal energy from a lower temperature to a higher…

A: Given question: A heat pump is a device that transfers thermal energy from a lower temperature to a…

Q: A locomotive exerts a constant force of 200,000 lbs on a set of series-connected railroad cars…

Q: If you PICK a point interactively without OSNAP, the selected point will be on the current…

A: The OSNAP command means Object Snap. If we enter -OSNAP command prompt, the many prompt are…

Q: Knowing that at the instant shown bar AB has a constant angular velocity of 6.5 rad/s clockwise,…

Q: A mechanic is trying to tighten a giant bolt using a wrench. Forces are applied at points A and B. y…

Q: Kerosene is placed inside a glass capillary tube having a radius of 0.5 mm. The kerosene inside the…

Q: The pendulum is suspended from point O and consists of two bars, each weighing 10 lb. Determine the…

A: Weight of each bar = 10 lb Length of OA= 2 ft Length of BC = 2 ft It is required to determine the…

Q: A cylindrical pressure vessel is made by shrinking a brass shell over a mild steel shell. Both…

A: Given Data The wall thickness is:hwall=6 mm The external diameter of the brass tube is:De=750 mm…

Q: can you answer part a and please accept the mass on the right (2m) as 2.5kg , the one on the left…

Q: Question 3 Three members of the same material and same cross-sectional area used to support the load…

Q: hand three planes of 'orthographic' projection (i.e., top, front, and side views). The dimensions of…

Q: Describe the method of measuring the included angle '0 'by using three hard steel discs of rollers…

A: Draw the diagram to measure the included angle θ.

Q: A 3m X 2m window has an exterior surface temperature of 220C, and the outside wind is blowing air at…

Q: The head loss between points (1) and (2) in the figure shown is 0.3 m. Determine the water mass flow…

Q: Two plates each having an area of 5 m^2 are 127 mm apart. The plate on top is fixed while the plate…

Q: Explain the words "multidimensional" and "parallel" by giving an example of each.

A: In this problem, it is asking for the meaning of "multidimensional" and "parallel" by giving an…

Q: Problem Solving. Solve the following problems completely. 5. Motors from two different manufacturers…

Q: Two objects, A and B, each of mass m, are connected by springs as shown in the figure below. The…

A: Given data: the observed value is 2.27 sec-1 vA or fA=1.81 sec-1 v1 or f1=1.14 sec-1

Q: A steam plant operates on the cycle given below. A 4 S 3 The pressure levels are 10 kPa and 6000…

A: Given Data: Pump efficiency, ηP=0.70 Turbine efficiency, ηT=0.75 Pressure at point 4 and 3, P3=…

Q: Which of the following statements is NOT CORRECT for a truss structure. Each member of a truss…

Concept explainers

Combined Loading

Any functioning component, such as machine parts, structural members, pressure vessels, and so on, are all under the influence of more than one force. When anybody is under the influence of more than one force such as shear forces, bending moments, axial forces, torsion, and so on, then such body is said to be under combined loading. A very practical example of combined loading is the crankshaft of an internal combustion engine (IC engine). The crankshaft of the IC engine is under high rpm, which is caused due to the torsional forces. Due to the presence of piston, counterbalances, and internal imbalances, the crankshaft experiences lateral forces and due to the rise in temperature, the crankshaft undergoes thermal expansion, which pulls the crankshaft along the axial direction and lateral direction. The presence of unbalanced loads along the periphery of the crankshaft also induces a bending moment.

Question

A solid shaft of circular cross section has a diameter of 15mm and is loaded by a torque of 130Nm at B and a torque of 560Nm at the free end (C). The material has a modulus of rigidity, G = 80 GPa.
Determine the total twist at the free end of the shaft (C)
y
O
O
O
O
1.9 rad
0.7 rad
2.6 rad
Don't Know
-0.05 rad
550mm
B
130Nm
650mm
с
560Nm

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1-

VIEW

Step 2

VIEW

Step by step

Solved in 2 steps with 2 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.

Similar questions

A shaft made from acrylic is subjected to the three torques indicated below. The acrylic has a shear modulus of 1.7 GPa. Determine: a. The twist at the end D if the diameter if the shaft is 100 mm. b. The minimum shaft diameter if Tallow = 10 MPa 200 N•m A 800 N•m 300 mm B 400 N•m 600 mm C 600 mm
A hollow aluminium shaft of 80 mm outer diameter & 60 mm inner diameter is rotating @ 5 Hz when constant 120 KW is applied. Use the following: G(alum)=28 GPa, a=1.80 m, b=0.80m & L=2.60 m. Assumed that the angle of twist is constant.The torque "T2" developed at right fixed support at B is ___KN-m 3.82 2.64 0.48 1.18 5.03
The torque of 100 kip - ft is applied in the 16-ft-long hollow steel shaft. Note that the inner diameter of the shaft is two-thirds of its outer diameter D. If the inner diameter is 8 inches, find the angle of twist of the shaft. Use G = 12 x 10^6 psi for steel.
A constant torque of 75 lb-in. is applied to the circular rod below, with a radius of 2 in. The shear modulus G = 3.5 x 106 psi. What is the angle of twist, p, at the end of the 6 foot long rod? 0.117 rad 0.056 rad 0.234 rad 0.314 rad T
A tapered, wrought iron shaft of length 5 ft, has 2 inch diameter at the fixed end and 0.8 inch diameter at the free end. Determine the angle of twist of the shaft, if it carries a torque, T = 2000 lb-in at the free end. Use G = 10^7 psi for wrought iron.
The solid-circular member AC, having a diameter D and a shear modulus of 69 GPa, is subjected to the torques 2T and 3T at points A and B, respectively. If Tallow = 35 MPa and (OA/c)allow =2°. detemine the maximum pemissible value of the torque T. Use the table given below and your student ID to find the values of L1, L2, and D. B A 3T 2T Student L1 (m) L2 (m) D ID (mm) 1131731 1 0.6 78
A hollow steel shaft with an outside diameter of 75 mm and a wall thickness of 5 mm is subjected to a pure torque of T = 4090 N-m. The shear modulus of the steel is G = 80 GPa. Determine the magnitude of the angle of twist in a 2.0-m length of shaft. O 0.0755 rad O 0.1029 rad O 0.0637 rad O 0.0561 rad O 0.0797 rad
The shaft of a motor has a length of 15 times its diameter and has a maximum twist of 1.5degrees when twisted at 2.5 KN-m torque. If the modulus of rigidity of the shaft is 83 Gpa,find the shaft diameter in m
A solid circular steel shaft having an outside diameter of 1.75 in. is subjected to a pure torque of T = 8130 lb-in. The shear modulus of the steel is G = 12,000 ksi. Determine the magnitude of the angle of twist in a 6.00-ft length of shaft. O 0.0338 rad O 0.0382 rad O 0.0530 rad O 0.0573 rad O 0.0430 rad
The compound shaft carries the two torques shown. The shear moduli are 28 GPa for aluminum, 83 GPa for steel, and 35 Gpa for bronze. If T = 1168.7 Nm, U = 4515 Nm, x = 3.01 m, y = 2.36 m, z = 1.35 m, d = 90 mm, and e = 83 mm, find the angle of rotation of the free end of the shaft. Round off the final answer to two decimal places. U T Aluminum Steel Bronze
The mean dimensions of the cross-section of the leading edge and torsion box of an airplane wing can be approximated as shown. If the wing is made of 2014-T6 (G = 19 GPa) aluminum alloy having an allowable shear stress of Tallow = 158 MPa, and the wall thickness is 12 mm. Determine the maximum allowable torque and the corresponding angle of twist per meter length of the wing.
Consider two steel shafts CFG and HJ of diameters 50 mm and 70 mm respectively as shown in fig. The shaft CFG is supported at two bearings, while shaft HJ is fixed at 'H' and supported by bearings at 'J. Determine the torques T 1 and T 2 if the twisting at gears C and G is required to be 0.05 rad. Take E=205GPA, G=70GPA 600 mm 75mm 600 mm 50mm 800mm G. T2