Answered: A square box of side 1 m having mass 40…

Name: A square box of side 1 m having mass 40 kg is submergend into the wate
Uploaded: 2024-03-20T06:56:55.000Z
Channel: Bartleby
Description: A square box of side 1 m having mass 40 kg is submergend into the water. A crane used to pull the box upto the surface of the water. Determine how much tension developed into the cable of the crane.

Engineering

Mechanical Engineering

A square box of side 1 m having mass 40 kg is submergend into the water. A crane used to pull the box upto the surface of the water. Determine how much tension developed into the cable of the crane.

International Edition---engineering Mechanics: Statics, 4th Edition

4th Edition

ISBN:9781305501607

Author:Andrew Pytel And Jaan Kiusalaas

Publisher:Andrew Pytel And Jaan Kiusalaas

Chapter8: Centroids And Distributed Loads

Section: Chapter Questions

Problem 8.122P: The 12-ft wide quarter-circular gate AB is hinged at A. Determine the contact force between the gate...

See similar textbooks

Similar questions

The 12-ft wide quarter-circular gate AB is hinged at A. Determine the contact force between the gate and the smooth surface at B due to water pressure acting on the gate. Use =62.4lb/ft3 for water.
One side of the container has a 03-m square door that is hinged at its top edge. If the container is filled with water, determine the smallest force F that must be applied to the bottom edge of the door to keep it closed.
The cylindrical water tank with R = 10 ft and H = 1.6 ft has thin steel walls of uniform thickness and weighs 18000 lb when empty. Determine the depth of the water h for which the center of gravity G of the tank plus water will be located at the surface of the water. For water, use =62.4lb/ft3.
The weight of the cylindrical tank is negligible in comparison to the weight of water it contains (water weighs 62.4lb/ft3). The coefficient of static friction between the tank and the horizontal surface is s. (a) Assuming a full tank, find the smallest force P required to tip the tank, and the smallest s that would allow tipping to take place. (b) If the force P = 200 lb initiates tipping, determine the depth of water in the tank.
The 280-kg, 6-m-wide rectangular gate is hinged at B and leans against the floor at A making an angle of 45° with the horizontal. The gate is to be opened from its lower edge by applying a normal force at its center. Determine the minimum force F required to open the water gate.
In the set-up shown, a rectangular gate, ABCD, is used to store layers of oil and water. Theweight of the gate is 4 kN and the force exerted by the stopper on the gate is measured tobe 30 kN.Draw the free body diagram of the rectangular gate.
The 0.5-m-radius semi-circular gate is hinged through the top edge AB. Find the required force to be applied at the center of gravity to keep the gate closed.
The 100cm radius cylinder weighs 3.1 KN and rest on the bottom of a container which is 1.5 meter long. Oil and water are poured into the left and right portion of the container to the depth of 0.8m and 1.4m respectively. Find the magnitude of the horizontal and vertical components of the force which will keep the cylinder touching the container at B.
A vertical bulkhead has a door 3m high and 2m wide fastened by two hinges A and B as shown and is kept closed by a bolt connected at C. Determine the reactions at the hinges and at the bolt if the water surface is 4m above the top of the door. water surface 4.0 m 1.5 m 1 bc 2.0 m Ao Bo 0.3 m -.1 m 0.3 m 4 2.4 m
A vertical rectangular plate is submerged in a fluid with its topedge parallel to the fluid’s surface. Show that the force exerted bythe fluid on one side of the plate equals the average value of thepressure up and down the plate times the area of the plate.
The uniform control gate AB shown is pinned at A and rests on the smooth surface at B. The gate has a width of 1m. If the gate has a mass of 3.9 Mg, determne the maximum depth of water h in the reservoir that will cause the gate to be on the verge of opening.
A 10 m x 15 m rectangular plate is submerged in water at 6 m. The plate is inclined at 35deg with the horizontal. The specific weight of water is given by y = 9.81 kN/m3. Obtain the resultant force of pressure on the plate.