A steel bar of rectangular cross-section 50 mm x 60 mm is pinned at one end and fixed at the other end. It is subjected to axial compression. If the proportional limit of the material is 240 MPa then (Take E = 210 x 103 MPa) A Ratio of minimum MOI and maximum MOI of the section is 0.694. Correct Option Minimum length of the column is 1341.22 mm. C Minimum length of the column is 1896.916 mm. Correct Option Slenderness ratio is used as a parameter to differentiate between long and short columns. Correct Option

A steel bar of rectangular cross-section 50 mm x 60 mm is pinned at one end and fixed at the other end. It is subjected to axial compression. If the proportional limit of the material is 240 MPa then (Take E = 210 x 103 MPa) A Ratio of minimum MOI and maximum MOI of the section is 0.694. Correct Option Minimum length of the column is 1341.22 mm. C Minimum length of the column is 1896.916 mm. Correct Option Slenderness ratio is used as a parameter to differentiate between long and short columns. Correct Option

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

Situation 2 For the assembly shown, determine the stress in each of the two vertical rods if the temperature rises 40°C after the load P=50 KN is applied. Neglect the deformation and the mass of the horizontal bar AB. Compute the vertical movement under the load. Steel Aluminum E=200 GPa E=70 GPa L-4m A=300 mm? a-11.7x10*/°C L-3m A=900 mm a=23x10“ /°C 3 m 3 m 3 m Situation 3
A steel bar of rectangular cross section 45 mm (height) x 60mm (base) and pinned at each end is subject to axial compression. The proportional limit of the material is 320 Mpa and E= 200 GPa. -Find least Radius of Gyration (in mm)? -Determine the transition length (in mm) in which the Parabolic formula may be used instead of the Euler's equation.? -Determine the transition slenderness ratio in which the Parabolic formula may be used instead of the Euler's equation.? -If the Length is 1 meter, determine the critical load (in KN) using pin support. -if the length is 3 meters, determine the critical stressn(in MPa) using pin support.
2. Axial loads are applied to the compound rod that is composed of an aluminum segment rigidly connected between steel and bronze segments. What is the stress in each material given that P = 10 kN? Specify whether tension or compression. Bronze Aluminum Steel A =400 mm2 A= 600 mm2 A = 300 mm2 2P ЗР 4P P -3 m 5 m 4 m Stress in Bronze (MPa) %D Stress in Aluminum (MPa) %3D Stress in Steel (MPa)
CLO 1: A rigid beam rests on two bronze bars 700 mm long. Another aluminum bar is placed between them which is 699.93 mm long. If the weight of the beam is 375 KN, determine the stress in the aluminum bar (in MPa). Bronze Bronze Alum Alum Bronze A in mm2 850 1500 E in Gpa 70 83 103.56 O 79.45 451.30 33.47
A rectangle column 500 mm x200 mm in cross-section is subjected to a compression load 1000 KN, the stress on the column is: a. 30 MPa b. 10 MPa C. 50 MPa d. 20 MPa
Situation 1: A rigid bar ABC weighs 10 kN/m. The compressive stress of the copper bar is 20 MPa. Answer the following questions: 3m B 2 m Copper L=3m A = 1500 mm² Brass C L = 2 m A = 1200 mm² A. What is the stress of the brass bar? Indicate if it will experience tension (T) or compression (C) (MPa) B. What is the minimum required diameter of the pin at A assuming that the pin connection is in double shear? Consider the allowable shearing stress of the pin as 15 MPa. Round your answer in a multiple of 5. (mm)
Problem II. An exhaust gas piping fabricated as shown is subjected to a bending moment, an internal pressure, and a torque. In points A and B, the following stresses occur due to the loading: o 63.5 MPa, B=127 MPa, = 127 MPa A.B A.B a. Determine Gmin, omax, and its direction (in degrees) from x-axis at point A. b. Determine omin, omax, and its direction (in degrees) from x-axis at point B. 1 B d O A x
The composite shaft consists of a mid-section that includes the 25-mm-diameter solid shaft and a tube that is welded to the rigid flanges at A and B. Neglect the thickness of the flanges. The shaft is subjected to a torque of T = 1000 N. m. The material is A-36 steel, G = 75 GPa (Figure 1) Part A Determine the angle of twist of end C of the shaft relative to end D. Express your answer using three significant figures. vec ? $C/D = 0.100 rad Submit Previous Answers Request Answer Figure 1 of 1 X Incorrect; Try Again; 5 attempts remaining ( Return to Assignment Provide Feedback 25 mm 75 mm 6 mm A 150 mm. 225 mm 1150 mm. 圓

= H.W A Solid Steel bar of diameter 60mm and length 350 mm is placed inside an aluminum cylinder of inside diameter 70mm and out side diameter Ilomm, a compressive load of looo la is applied on the assembly, find the stresses in the bar and the cylinder? take Est = 200 GPa and EA1 = 70 G Pa. P=1000k Cover Plate 0.25mm dif do 350mm Alum, cylinder Steel bar
The composite shaft consists of a mid-section that includes the 25-mm-diameter solid shaft and a tube that is welded to the rigid flanges at A and B. Neglect the thíckness of the flanges. The shaft is subjected to a torque of T = 1000 N. m. The material is A-36 steel, G = 75 GPa (Figure 1) Part A Determine the angle of twist of end C of the shaft relative to end D. Express your answer using three significant figures. ΑΣφ vec $C|D = 0.0542 rad Submit Previous Answers Request Answer Figure X Incorrect; Try Again; 4 attempts remaining
Portions of a x-in. square bar have been bent to form the two machine components shown. Knowing that the allowable stress is 18 ksi, determine the maximum load that can be applied to each component. (a) 1 in. (b) The maximum load that can be applied to component (a) is The maximum load that can be applied to component (b) is lb. lb.
PROBLEM 6/6 F = 520 kN Determine the stress in each aluminum and steel bars after 0.2 mm F = 520 kN is applied. Note that a gap of 0.2 mm exist before the external load is Steel 280 mm applied and bars has equal distance with each other. Neglect the weight at the flat form. A = 1100 mm² E = 200 Gpa A = 2500 mm² E = 70 GPa Steel Aluminum