Answered: A steel flat plate of 20 mm thickness,…

A steel flat plate of 20 mm thickness, uniformly tapers from 200 mm to 100 mm width in the a length of 500 mm. Find the extension of the plate if an axial pull of 40 kN is applied at its ends.

International Edition---engineering Mechanics: Statics, 4th Edition

4th Edition

ISBN:9781305501607

Author:Andrew Pytel And Jaan Kiusalaas

Publisher:Andrew Pytel And Jaan Kiusalaas

Chapter7: Dry Friction

Section: Chapter Questions

Problem 7.78P: The figure shows a steel bar being processed by a rolling mill. Given that P=80kN and r =0.016,...

See similar textbooks

Related questions

Q: Flat belt 100mm wide and 8mm thick transmits power between two pulleys, running at 1600 m/min. The…

Q: A steel wheel of 800mm diameter on a horizontal steel rail. It carries a load of 60ON. The…

A: We have to calculate rolling force

Q: A flange bolt coupling consists of six ½” diameter bolt spaced evenly around a bolt circle of 14”…

A: Given that: six 1/2 inch bolts are evenly spaced. Bolt circle diameter is 14 inches. Allowable…

Q: A flange bolt coupling is used to connect a solid shaft 90 mm in diameter to a hollow shaft 100 mm…

Q: A uniform shaft of diameter 30 mm is subject to a 60 N of tangential force. Calculate the shear…

A: Given data: The diameter of the shaft is D = 30 mm. The tangential force acting on the shaft is F =…

Q: Consider the 1inch steel square tube loaded in torsion.the tube has wall thickness of 0.0196 inch…

A: Given: maximum allowable shear stress = 7.2 kpsi tube wall thickness = 0.0196 inch Do = 1 inch Di =…

Q: A hollow steel shaft, 500 mm outside diameter and 300 mm inside diameter, has a coupling 80 mm thick…

A: Given data: Outside diameter of hollow shaft = 500 mm Inside diameter of hollow…

Q: ghtening force of 2200 N. If the bolt used has metric threads of 4 mm pitch, the torque requi

A: given:tightening force =2200NPitch=4mm

Q: 3.51 Fig. shows a circular steel bar. (a) and Fig. square steel bar (b) have the same torque T…

A: Givenfor circular shaft r=aπfor square shaftside=a

Q: A rectangular key is used in a pulley connected to a line shaft at 15 kW and 600 rpm. If shearing of…

A: Given:P=15 kWN=600 rpmζ=230 MPaw=d4l=1 in =0.0254 m

Q: 11 A rectangular bar section of aluminium alloy has outside dimensions 100 mm x 50 mm, as shown in…

A: As illustrated in the image, a rectangular bar section of aluminium alloy has outer dimensions of…

Q: A flanged bolt coupling consist of six 10 mm diameter steel bolts on a bolt circle 300 mm. in…

Q: For the figure below, the average shearing stress in each rivet is .kPa (Hint: Two 22-mm-diameter…

Q: A metallic cube of side 5cm, has its lower surface fixed rigidly. When a tangential force 98100 N…

Q: A flanged bolt coupling is used to connect a solid shaft 120 mm in diameter to a hollow shaft 100 mm…

Q: Compute the torsional shear stress in a circular shaft with a diame to a torque of 800 N-m.

Q: A rigid bar, hinged at one end, is supported by two identical springs as shown in Fig. P-349. Each…

Q: The constant wall thickness of a tube with the elliptical cross section shown is 0.12 in. what…

A: As per given Question Wall thickness =0.12in Shear force =6000 psi We have to determine the torque

Q: 10-spline shaft ( d= 0.91D, w= 0.156D, h= 0.045D ) and permanent fit has a diameter of 70 mm. Find…

Q: A steel tube of outer diameter 86mm and inner diameter 52mm is under pure torsion. The diameter of a…

A: Outer diameter = 86 mm Inner diameter = 52 mm Answer is (B) 81.98 mm

Q: 5. A rigid bar is smooth pinned at O and supported by two identical springs as shown. Each light…

A: Given Turns = 20 Wire diameter = 3/4 Mean diameter = 7 inch Maximum shear stress = 18 ksi To find…

Q: Calculate the amount of torque generated by the rod with circular cross-section as shown in the…

A: Given: Force = 48 lb Diameter = 5 in.

Q: the load on each tire of the car is 1000kg and the tires diamater is 50cm . if the coefficient of…

Q: QI/ The 15-mm diameter steel bolt is screwed tightly into a block at A. Suppose that the couple…

A: Write the length of the wrench. L=300 mm=300 mm×1 m1000 mm=0.30 m Write the displacement of the…

Q: Prove that the most efficient triangular section is the one with a 90° vertex angle.

A: Area of the triangular section, A=my(y)=y2tanϕ Wetted perimeter, P=2y01+m2=2ysecϕ

Q: find the smallest diameter bolt that can be used in the clevis P=400KN shearing strength of the…

Q: A 4-spline shaft and to slide when not under load has a diameter of 2.5 in. Find the compressive and…

A: Givend=2.5inP=2500lbsL=2in

Q: A circular shaft of diameter 120 mm is welded to a rigid plate by a fillet weld of size 6 mm. If a…

Q: A hollow vertical cylindrical steel pipe with an outside diameter of 300 mm and 6 mm thick has a…

Q: 4. A small race car has an aluminum hub (shown in red). The drive axle is press-fit into the hub,…

Q: In a bolted joint two smooth members are connected with an axial tightening force of 2200 N. If the…

Q: Find the R ratio for this cyclic loading

A: Given; Mean stress=+140MPaMinimum stress=-70MPaTherefore we have to find R ratio?

Q: Two steel plates grade 300 having the same dimensions (250mm width x 25mm depth) are joint using…

A: Given data, Applied force, F = 950 kN = 950000 N Shear strength of the bolt, τs,bolt=0.6×830=498 MPa…

Q: A 3/8 inch flat leather belt is 12 inch wide and is used on a 24 inch diameter pulley rotating at…

Q: -In the clevis shown in Fig. below, find the minimum bolt diameter and the minimum thickness of each…

Q: The members of the structure in Fig. weigh 200lb/ft. Determine the smallest diameter pin that can be…

Q: A square steel bar, 25 mm on a side and 650 mm long, is subjected to a torque of 230 N #m. Compute…

Q: Calculate the force (kN) required to punch a circular blank of 942.5 mm" surface area in a plate of…

Q: A torque To is transmitted between two flanged shafts by means of four 20-mm bolts. diameter of the…

A: Schematic diagram of flanged shaft after considering the force F in the bo;t due to torque T

Q: (6) A double square-threaded power screw transmits 1,800in-lb of torque and raises a machine head;…

Q: The bell crank as shown in the fig. is in equilibrium, determine the shearing force in the pin at

Q: Five movable pulleys are arranged as in the first system of pulleys. If the efficiency of the system…

A: Given data as per question No. of pulleys =5 The efficiency of the system = 80% The load has to be…

Q: In a tensile test on a steel tube of external diameter 18 mm and internal diameter 12 mm, an axial…

A: Given data To determine poisson's ratio and ther modulus

Q: 1000mm Input shaft A 100mm Bearing support 200mm 450mm pulley pulley 200mm 150mm 450mm pulley…

A: NOTE:- As per our company guidelines we are supposed to answer only first 3 sub-parts. Kindly repost…

Q: A leather belt which is 125 mm wide and 6 mm thick, is used for transmitting power from a pulley.…

A: Given l= 125 mm w = 6mm d = 750 mm n = 500rpm Theta = 150o Mass ratio with volume = 1 m3 for 1 kg…

Concept explainers

Forming and Shaping

Metal forming is a category of metalworking process through which the material can be given the desired shape and size by subjecting it to plastic deformation, where the component undergoes bulk deformation process upon application of loads. Unlike the shearing and machining process, the material does not undergo up to a failure point as indicated in the stress-strain curve. Hence, the stresses induced during the forming process are greater than yield strength but less than the failure strength of the material. The process does not lead to the loss of material, so it can be said to be an economical process. During forming, the material is subjected to tensile forces, compressive forces, bending, and shearing loading conditions. The material should possess the property of ductility to undergo the forming process.

Question

A steel flat plate of 20 mm thickness, uniformly tapers from 200 mm to 100
mm width in the a length of 500 mm. Find the extension of the plate if an
axial pull of 40 kN is applied at its ends.
bị

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

This is a popular solution!

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Trending now

This is a popular solution!

Step by step

Solved in 2 steps with 1 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.

Similar questions

The figure shows a steel bar being processed by a rolling mill. Given that P=80kN and r =0.016, determine the force F required to advance the bar at a constant speed.
Q 2 A steel flat plate of 20 mm thickness, uniformly tapers from 200 mm to 100 mm width in the a length of 500 mm. Find the extension of the plate if an axial pull of 40 kN is applied at its ends.
5. An open belt 100 mm wide connects two pulleys mounted on parallel shafts with their centres 2.4 m apart. The diameter of the larger pulley is 450 mm and that of the smaller pulley 300 mm. The coeffi- cient of friction between the belt and the pulley is 0.3 and the maximum stress in the belt is limited to 14 N/mm width. If the larger pulley rotates at 120 r.p.m., find the maximum power that can be trans- mitted. [Ans. 2.39 kW]
The bar in the attached picture has a thickness of 16mm and a total width of 48mm. The pin has an diameter of 11mm.....
The lap joint shown is fasted by 20mm diameter rivets. Calculate the maximum safe load P that can be applied if the shearing stress in the rivet is limited to 96MPa and the bearing stress is limited to 124 MPa. Assume the Applied load is uniformly distributed among the four rivets.
a b c d h 82 mm 139 mm 39 mm 18 mm 33 mm Clamps like the one shown are commonly used in woodworking applications. This clamp has the dimensions given above, and its jaws are 38 mm wide (in the direction perpendicular to the plane of the picture). The screws of the clamp are adjusted so that there is a uniform pressure of 190 kPa being applied to the workpieces by the jaws. Find the force carried in each screw.Note: Assume that A, B, C, and D act as pins. (Denote tension forces with positive values; compressive forces with negative values.)
4.As shown in the figure, a square threaded screw is used in a vise to exert a pressure of 2 tons. If the screw is double-threaded and has a pitch of 0.25 m and a mean radius of 1.5 inch, determine the torque that must be applied at B to create this pressure. Assume the coefficient of friction to be 0.15. P
In a bolted joint two smooth members are connected with an axial tightening force of 2200 N. If the bolt used has metric threads of 4 mm pitch, the torque required for achieving the tightening force is
Find strain
An open belt 100 mm wide connects two pulleys mounted on parallel shafts with their centres 2.4 mapart. The diameter of the larger pulley is 450 mm and that of the smaller pulley 300 mm. The coefficient of friction between the belt and the pulley is 0.3 and the maximum stress in the belt is limited to14 N/mm width. If the larger pulley rotates at 120 r.p.m., find the maximum power that can be transmitted
Assume that the axial load P applied to the lap joint is distributed equally among the three 20-mm-diameter rivets. What is the maximum load P that can be applied if the allowable stresses are 40 MPa for shear in rivets, 90 MPa for bearing between a plate and a rivet, and 120 MPa for tension in the plates?
3. The rail roads are usually made of steel material segments with a 10 m long. Between each segments there are some spacing for the contraction and expansion because of temperature differences. a. When the temperature of certain region is changes between -20.0 °C and 30 °C how much space they should put between each segment? b. If the segments are originally in contact, what is the stress in them at 30 °C?