A steel propeller shaft is to transmit 4.5 MW at 3 Hz without exceeding a shearing stress of 60 MPa or twisting through more than 1° in a length of 26 diameters. Compute the proper diameter if G = 83 GPa.

A steel propeller shaft is to transmit 4.5 MW at 3 Hz without exceeding a shearing stress of 60 MPa or twisting through more than 1° in a length of 26 diameters. Compute the proper diameter if G = 83 GPa.

Mechanics of Materials (MindTap Course List)

9th Edition

ISBN:9781337093347

Author:Barry J. Goodno, James M. Gere

Publisher:Barry J. Goodno, James M. Gere

Chapter3: Torsion

Section: Chapter Questions

Problem 3.12.4P: The stepped shaft shown in the figure is required to transmit 600 kW of power at 400 rpm. The shaft...

See similar textbooks

Related questions

Q: 4. A pair of gears with a reduction ratio of 2.32 operating on 83mm cen- tres is required. The…

A: Q-4 part (g): The input power is 31.416 kW

Q: In an air-standard Otto cycle engine, the following data were obtained: k = 1.4, P₁ = 103 kPa, t₁ =…

Q: 1:- Find the power of the main electric motor required in a lathe machine to operate a steel welder…

A: INTRODUCTION: One of the traditional machines is the lathe. The lathe machine's primary duty is to…

Q: Q3-Blocks A and B have a mass of 7 kg and 10 kg, respectively, and there are pulleys at C and D.…

Q: A spur gear has pitch circle diameter D and number of teeth T. The circular pitch of the gear is 2πD…

Q: A 6-in-wide and 8-in-high vertical hot surface in 78°F air is to be cooled by a heat sink with…

A: In thermodynamics when the energy from the high temperature medium to the low temperature medium…

Q: Find Resultant, magnitude, & position

Q: In a Rankine cycle the turbine work is 1000 KJ/kg and pump work of 13 KJ/kg. If heat generated by…

A: GivenWT=1000kJ/kgWP=-13 kJ/kgQ=2800kJ/kg

Q: Locate the centroid of the shaded area shown. y 2. 120 40 40 30 1 30 20 20 50- 120

Q: 0.07088lbm/ft3, μ = 0.04615 lbm/ft-hr) is to be transported through a 550 ft long circular cast iron…

Q: Electrical discharge machining process, breakdown voltage across inter electrode gap (IEG) IS 400 V…

Q: A// For laminar flow over a flat plate, the local heat transfer coefficient h, is known to where x…

A: given; local heat transfer coefficient(hx) vary with x-1/5 so;hx=k*x-1/5where;k=constantheat…

Q: Sketch diagrams (including a coordinate system) showing the planes represented by the following…

Q: Q6. A small size cooling tower is designed to cool 400kg of water per minute. The water enters the…

Q: draw the free-body diagram

Q: in Figure (6.21) is a solid circular rod with diameter d=10 mm. Determine the axial stress o in the…

Q: Q6. A small size cooling tower is designed to cool 400kg of water per minute. The water enters the…

Q: 6. (a) The temperature distribution across a wall of an aluminium cylin- der block, 4 mm thick at a…

Q: The ratio h₂/h₁ is 104

A: Given; Determine the ratio of h2/h1?where, Head loss is = h1 Pipe length and fluid remaining the…

Q: Write a short paper that discuss the worldwide trend and application of the technology relative to…

A: given; Write a short paper that discuss the worldwide trend and application of the technology…

Q: A pair of gears with a reduction ratio of 2.32 operating on 83mm cen- tres is required. The module…

A: Given : m=02 mm x=0 (for standard gear x=0) to find,…

Q: magnitude of total work done (in kJ) on the

A: Given; V1=10 m/sV2=20 m/s Elevation increases by 20 m ∆T=1 KMass= 10 kg Cv=100 J/kg K Gravitational…

Q: A reheat-regenerative Rankine cycle, producing 250 MW, has two feedwater heaters, a closed one for…

Q: 28. 2.5 kg/min of saturated steam at 4.6 MPa expand adiabatically until its temperature is 200 deg…

A: Mass flow rate, m˙= 2.5 kg/min= 2.560 kg/s State 1: Saturated steam and P1= 4.6 MPa State 2: T1=…

Q: Q2: For the raw data shown in Table below: 1) Find out which of the x₁ or x₂ variables is better…

Q: Thank you for the answer. but sir/ma'am it's kind of blurry can you do something about it if no,…

Q: Define the friction losses in pipes, what are the parameters that effect on friction in the pipe?…

A: Pump head, Hp=4 mPipe diameter, D=10 cm=0.1 mDiameter at nozzle exit, d=5 cm=0.05 mFriction factor,…

Q: hiaxial yield stress of a material is 420 MPa etermine shear yield stress using Von Mise.

Q: 26. Saturated steam at 3.27 MPa undergoes a T = c process until its pressure becomes 0.8 MPa.…

Q: Use the process of partial fractions to determine the inverse Laplace of the following functions: s²…

Q: The orthographic views of an object are shown below. a) Draw its isometric drawing using a pencil.…

Q: Water is flowing from the tank into a series of pipes and then into the atmosphere through 75…

Q: Blocks A and B have a mass of 7 kg and 10 kg, respectively, and there are pulleys at C and D. Using…

A: there are two interfaces

Q: Q.1 Determine the force (P) shown in figure knowing that the resultant of two forcec passes through…

Q: The temperature distribution across a wall of an aluminium cylin der block, 4 mm thick at a certain…

Q: Steam is entering a turbine at 5 MPa and 400°C and exits at 10 kPa going to a condenser. The work…

Q: T 2.5" 1 ly 3" To

Q: maximum shear stress in the wall?

A: Given data; Inner radius,r=8 mm Wall thickness,t= 50 mm Gauge pressure=4 MPa Determine the maximum…

Q: 17 A gas occupies 0.2 cu. m. at 65.8 kPa & 20°C. Find its volume at STP. * 1.210 cu m 12.10 cu m O…

Q: Explain the concept of formation and stability of metal-complexes and its application for the…

A: Concept of formation and stability of metal complexes: A species that is formed between an ion of…

Q: 3) Determine the moment of inertia of the composite area about the x and y axes

Q: The maximum principle stress for the stress state shown in the figure is (b) 20 (a) o (c) 30 (d) 1.5…

A: From the data given in question, Normal stress along x direction = σx = σ Normal stress along y…

Q: Q'/ If the fitting symbol between the shaft and hole is (8G7/h6), find? 1-The upper and lower…

Q: Q1) A steel cylinder 10 cm in diameter and 10 cm long is initially at 300 °C. It is suddenly…

Q: In Part a, could you please explain where the 4 comes from on the line before the answer.

Q: F6-11. Determine the force in members GF. GD, and CD of the truss. State if the members are in…

Q: 4. A pair of gears with a reduction ratio of 2.32 operating on 83mm cen- tres is required. The…

A: Since you have asked only specific question so i answer only the subpart H for you. Given Data The…

Q: In the system shown, a force P(t) is applied at C. Bar ABCD is of negligible mass. Determine: The…

Q: H.W3 Determine the slope and deflection of end A of the cantilevered beam. E = 200 GPa and I =…

Q: Q1-A 75-Kg man wants to pull a 145- Kg box and the coefficient of static friction between the box…

A: Given data Mass of man = 75kg Mass of box = 145 kg. Coefficient of static friction between box and…

Concept explainers

Combined Loading

Any functioning component, such as machine parts, structural members, pressure vessels, and so on, are all under the influence of more than one force. When anybody is under the influence of more than one force such as shear forces, bending moments, axial forces, torsion, and so on, then such body is said to be under combined loading. A very practical example of combined loading is the crankshaft of an internal combustion engine (IC engine). The crankshaft of the IC engine is under high rpm, which is caused due to the torsional forces. Due to the presence of piston, counterbalances, and internal imbalances, the crankshaft experiences lateral forces and due to the rise in temperature, the crankshaft undergoes thermal expansion, which pulls the crankshaft along the axial direction and lateral direction. The presence of unbalanced loads along the periphery of the crankshaft also induces a bending moment.

Question

A steel propeller shaft is to transmit 4.5 MW at 3 Hz without exceeding a shearing stress of 60 MPa or
twisting through more than 1° in a length of 26 diameters. Compute the proper diameter if G = 83 GPa.

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Step by step

Solved in 2 steps with 2 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.

Similar questions

A motor driving a solid circular steel shaft with diameter d = 1.5 in, transmits 50 hp to a gear at B, The allowable shear stress in the steel is 6000 psi. Calculate the required speed of rotation (number of revolutions per minute) so that the shear stress in the shaft does not exceed the allowable limit.
What is the maximum power that can be delivered by a hollow propeller shaft (outside diameter 50 mm, inside diameter 40 mm, and shear modulus of elasticity 80 GPa) turning at 600 rpm if the allowable shear stress is 100 MPa and the allowable rate of twist is 3.0°/m?
A full quarter-circular fillet is used at the shoulder of a stepped shaft having diameter D2= 1.0 in. (see figure), A torque T = 500 lb-in. acts on the shaft. Determine the shear stress at the stress concentration for values as follows: D1= 0.7,0.8, and 0.9 in. Plot a graph showing versus D?
A tubular shaft being designed for use on a construction site must transmit 120 kW at 1,75 Hz, The inside diameter of the shaft is to be one-half of the outside diameter. If the allowable shear stress in the shaft is 45 MPa, what is the minimum required outside diameter d?
The stepped shaft shown in the figure is required to transmit 600 kW of power at 400 rpm. The shaft has a full quarter-circular fillet, and the smaller diameter D1= 100 mm. If the allowable shear stress at the stress concentration is 100 MPa, at what diameter will this stress be reached? Is this diameter an upper or a lower limit on the value of D2?
A square tube section has side dimension of 20 in. arid thickness of 0.5 in. If the section is used for a 10-ft-long beam subjected to 1250 kip-in, torque at both ends, calculate the maximum shear stress and the angle of twist between the ends. Use G = 11,600 ksi.
A stepped shaft ACB having solid circular cross sections with two different diameters is held against rotation at the ends (sec figure). If the allowable shear stress in the shaft is 6000 psi, what is the maximum torque (T0) that may be applied at section C? Find (T0)max if the maximum angle of twist is limited to 0.55º. Let G = 10,600 ksi.
A hollow steel propeller shaft is to transmit 4.5 MW at 3 Hz without exceeding a shearing stress of 50 MPa or twisting through more than 1deg in a length of 26 diameters. Compute the proper diameter if Do =2Di. Show your complete solution.
A hollow shaft has an inner diameter of 0.035m and outer diameter of 0.06m. Compute for the torqueif the shear stress is not to exceed120 MPa in N-m.
A solid shaft is required to transmit 120 kW power at 200 rpm. Find the suitable diameter of the shaft if the maximum torque transmitted in each revolution exceeds the mean by 20%. Take allowable shear stress as 70 N/mm2 for the material of the shaft.
Compute the torsional shear stress in a hollow shaft with an outside diameter of 40 mm and an inside diameter of 30 mm when transmitting 28 kilowatts(kW) of power at a speed of 45 rad/s.
A circular-closed-tube shaft, with an outer radius of 20 mm and an inner radius of 15 mm, and 650 mm long, is transmitting 50kW of power while rotating at a frequency of 20HZ. Compute the maximum shear stress (in Pa) and the angle of twist (in degree) for the shaft. The shear modulus G is 100 GPa. Hint: Please refer to the table of K and Q factors in the lecture notes.