A tank is connected with cart by the rope A as shown in figure. When the water leaves the tank from the nozzle, it falls and strikes a vane attached to another cart. Neglect the friction effect. i. Compute the velocity of water leaving the tank Vi and water velocity leaving the cart V2. ii. Deterime the tensions in the rope A and the rope B. Nozzle area = 0.01 m? 2 m Horizontal free jets 4 m Rope A Rope B

A tank is connected with cart by the rope A as shown in figure. When the water leaves the tank from the nozzle, it falls and strikes a vane attached to another cart. Neglect the friction effect. i. Compute the velocity of water leaving the tank Vi and water velocity leaving the cart V2. ii. Deterime the tensions in the rope A and the rope B. Nozzle area = 0.01 m? 2 m Horizontal free jets 4 m Rope A Rope B

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

4. A centrifugal pump delivers water to a height of 22 metres at a speed of 800 r.p.m. The velocity of flow is constant at a speed of 2-0 m/s and the outlet vane anglc is 45°. If the pump discharges 225 litres of water per second, find the diameter of the impeller and width of the impcller at oudet. (Ans. 375 mm: 95 mm)
Pump BC shown brings oil (SG = 0.72) to reservoir D at 170 L/sec. The energy lost from A to B is 1.1 J/N and from C to D is 4.7 J/N. How many hp is needed for the pump to function if its efficiency is just 80%?
QUESTION 1 A jet of freshwater strikes a series of vanes of a turbine at 25° with the direction of motion and leaves it at 150° absolute with the direction of motion. The absolute inlet velocity of the jet is 25 m/s and the vanes move at a velocity of 10 m/s. Ignore friction across the vanes. Calculate: 1.1 the vane inlet angle. 1.2 the vane outlet angle. 1.3 the power/kg of water and, 1.4 the hydraulic efficiency.
QUESTION 1 A jet of freshwater strikes a series of vanes of a turbine at 25° with the direction of motion and leaves it at 150° absolute with the direction of motion. The absolute inlet velocity of the jet is 25 m/s and the vanes move at a velocity of 10 m/s. Ignore friction across the vanes. Calculate: 1.1 the vane inlet angle. 1.2 the vane outlet angle. 1.3 the power/kg of water and, 1.4 the hydraulic efficiency. QUESTION 2 A pipeline of 50 mm diameter and 4.5 km length connects two reservoirs whose constant difference of water level is 12 m. A branch pipe 1.25 km long and taken from a point distance of 1.5 km from reservoir A, leads to reservoir C whose water level is 15 m below that of reservoir A. Find the diameter of the branch pipe so that the flow into both the reservoirs is the same. Assume the coefficient of friction for each pipe, f = 0.0075, and neglect minor losses. QUESTION 3 The plunger diameter of a single-acting reciprocating pump is 115 mm and the stroke is 230 mm.…
A water jet with a flow rate of 2.83 m3 / s is traveling at 6 m / s in the positive x direction. The cost of the current striking a stationary splitter is correct about a 45 aç angle, other company are deflected downwards by the same angle and the final velocities of the two streams are 6 m / s. By neglecting the gravity, the separator is in place against the force applied by the water. calculate the x- and z- power of what is required to hold it. For water ? = 1.184 kg / m3
Q2/ An outward flow reaction turbine has tangential velocity at its inner rim as 20 m/s, and ratio of radii is 0.9. The turbine is placed 1 m below the water surface and blade angle are 90° and 20° at inlet and outlet respectively. The radial velocity of flow at inlet is 6 m/s. Neglecting frictional losses and taking the discharge as radial, draw velocity triangles at inlet and outlet and find: (a) guide vane angle (b) the velocity of water from the guides. (c) total head of water (d) hydraulic efficiency
5.9 Diffuser vanes are sometimes used in centrifugal pumps to increase the static pressure at discharge. A few such vanes are shown in the following figure. If the flow rate is 0.1 m³/s and the height of blades is 2 cm, find the increase in static pressure. The inside and outside radii are 15 cm and 21 cm, respectively. 104 Turbomachinery: Concepts, Applications, and Design 14° 27°
While rotating at 900 rpm, a centrifugal pump delivers 2500 gpm of water at ahead of 75 ft. If the impeller diameter is 1.5 ft. and the blade width is 1.75 in.,find the (a) blade angle β2, (b) radial velocity Vr2, and (c) blade speed u2. Assumeno whirl at the inlet.Ans: β2=12.5°; Vr2=8.1 ft./s; u2=70.7 ft./s
1.A pipe of diameter 300 m and length 3000 m is used for the transmission of power by water. The total head at the Inlet of the pipe is 400 m. Find the maximum power available at the outlet of the pipe. Take f=0.005 2. The head of water at the Inlet of a pipe of length 1500 m and diameter 400 mm is 50 m. A nozzle of diameter 80 mm at the outlet, is fitted to the pipe. Find the velocity of water at the outlet of the nozzle if f=0.01 for the pipe.
A jet of freshwater strikes a series of vanes of a turbine at 25° with the direction ofmotion and leaves it at 150° absolute with the direction of motion. The absolute inletvelocity of the jet is 25 m/s and the vanes move at a velocity of 10 m/s. Ignore frictionacross the vanes. Calculate:1. the power/kg of water
Patm A. water Tank B hi h2 As shown in the figure, at hi= 1.8 m, h2= 3.6 m positions, the water in the tank is discharged by means of a pump. The diameter of the pipe is D- 75 mm. Since the ambient pressure is 10 bar, calculate the velocity of the water in the pipe, the flow rate of the system and the absolute pressure at the peak (point B), ignoring all friction losses. Patm Note: If you find it necessary to solve the problem, you can make assumptions. But you must write down your assumptions. Take the gravity as g= 9.806 m/s² Hint: You can start with using Bernoulli Equation for A and C points.
The sprinkler system is used for watering the garden as given figure below. Working fluid enters the system at 2,02 liters/s. Calculate the required torque (N.m] holding the system as stationary for e-30°. (NOTE: Take p-1000 ka/m) Nozzle exit area normal to relative velocity = 18 mm =0.5m Yanıt: