A tensile test is conducted on a mild steel bar. The following data was obtained from the test : diameter of the steel bar= 3cm, Gauge Length of the bar = 20cm, Load at Elastic limit= 250kN, Extension at a load of 150kN= 0.21 mm, Maximum Load = 380kN, Total Extension= 60mm, Diameter of the rod at failure=2.25cm, determine young's modulus?

A tensile test is conducted on a mild steel bar. The following data was obtained from the test : diameter of the steel bar= 3cm, Gauge Length of the bar = 20cm, Load at Elastic limit= 250kN, Extension at a load of 150kN= 0.21 mm, Maximum Load = 380kN, Total Extension= 60mm, Diameter of the rod at failure=2.25cm, determine young's modulus?

Mechanics of Materials (MindTap Course List)

9th Edition

ISBN:9781337093347

Author:Barry J. Goodno, James M. Gere

Publisher:Barry J. Goodno, James M. Gere

Chapter1: Tension, Compression, And Shear

Section: Chapter Questions

Problem 1.6.7P: A wine of length L = 4 ft and diameter d = 0.125 in. is stretched by tensile forces P = 600 lb. The...

See similar textbooks

Similar questions

A wine of length L = 4 ft and diameter d = 0.125 in. is stretched by tensile forces P = 600 lb. The wire is made of a copper alloy having a stress-strain relationship that may be described mathematically by =18,0001+30000.03(=ksi) in which is nondimensional and has units of kips per square inch (ksi). (a) Construct a stress-strain diagram for the material. (bj Determine the elongation, of the wire due to the Forces P. (c) IF the forces are removed, what is the permanent set of the bar? (d) If the forces are applied again, what is the proportional limit?
A tensile test was conducted on a mild steel& the following data was obtained as follows. Diameter of the steel bar = 3 cm,Gauge length of the bar = 20 cm. Load at elastic limit = 250 kN . Extension at a load of 150kN = 0.21 mm . Maximum load = 380 kN . Total extension = 60 mm . Diameter of the rod at failure = 2. 25 cm Determine: (a) Young’s modulus (b) stress at elastic limit (c)the percentage of elongation (d) Percentage decrease in area.
4. A mild steel material is tested using universal testing machine & the following data was obtained as follows. Diameter of the steel bar = 5 cm, (ii) Gauge length of the bar = 150 cm, Load at elastic limit 650 kN (iv) Extension at a load of 350kN = 0.25 mm, Maximum load = 500 kN (vi)Total extension failure = 1.5 cm. Determine: (a) Young's modulus elastic limit (c) the nercentage of elongation in area. %3D = 5.5 cm, Diameter of the rod at (b) (d) Percentage decrease stress at
A test specimen in a tensile test has a gage length of 2.0 in and an area = 0.5 in?. During the test the specimen yields under a load of 32,000 lb. The corresponding gage length = 2.0083 in. This is the 0.2 percent yield point. The maximum load of 60,000 lb is reached at a gage length = 2.60 in. Determine: (a) Yield strength (b) Modulus of elasticity (c) Tensile strength (d) If the specimen necked to an area = 0.25 in', determine the percent reduction in area
A solid cylindrical bar is subjected to tensile test. The initial diameter of the bar is 60 mm. The change in diameter (Ad) after the test is 0,01438 mm. The applied load is 130 kN. The inital length of the bar is 240 mm. The change in length (Al) after the test is 0,1987 mm. Evaluate the Modulus of Elasticity (GPa)
Experiments were conducted in a tension testing machine to evaluate the material properties of two metallic rods both having diameter equal to 10 mm. First rod having modulus of rigidity of the material equal to 400 tonnes/cm2 when subjected to an axial tensile force of 6 kN, the change in its diameter was observed to be 0.0018 cm. The value for the bulk modulus of the second metallic rod is same as that of the first one but modulus of elasticity 18% more. Based on the material properties calculate and compare the values of different moduli as well as Poisson’s ratio for both metallic rods. Justify your answer with reasons.
Results of a tensile test of a 0.505-in. diameter aluminum alloy test bar are shown below. Initial length = 2.0 in. The proportional limit occurred with a load = 7000 lbs. What is the length after deformation of another bar (same aluminum alloy material) of initial length of 50 in. at a stress level of 30,000 psi? Load (Ib) (A) (in.) 0.000 1000 0.001 3000 0.003 5000 0.005 7000 0.007 7500 0.030 7900 0.080 8000 (maximum load) 0.120 7950 0.160 7600 (fracture) 0.205 O A. 50.1 in. O B. 50.3 in. O C.50.15 in. O D. 51.5 in.
Search nations Slide Show Review View Help A A A E E EE E e AV Aa 2 A- Shapes Ar Font Paragraph 13. For a given material, Young's modulus is 110 GN/m2 and shear modulus is 42 GN/m2. Find the bulk modulus and lateral contraction of a round bar of 37.5 mm diameter and 2.4 m long when stretched 2.5 mm
A tensile test is being conducted on a steel-rod specimen with a gauge length of L0=4.0 in and an initial diameter of d0=0.75 in. If the final length of the rod at fracture is Lt= 5.53 in, find the percent elongation of the rod at fracture
A specimen of titanium alloy is tested in torsion and the shear stress–strain diagram is shown in Fig.a. Determine the shear modulus G, the proportional limit, and the ultimate shear stress. Also, determine the maximum distance d that the top of a block of this material, shown in Fig. b, could be displaced horizontally if the material behaves elastically when acted upon by a shear force V. What is the magnitude of V necessary to cause this displacement?
A mild steel bar went through a tensile test conducted at the University of San Carlos Mechanical Engineering Laboratory. The following data was obtained from the test: i. Diameter of the steel bar = 30 mm ii. Gauge length of the bar = 200 mm iii. Load at the elastic limit = 250 kN iv. Extension at a load of 150 kN = 0.21 mm v. Maximum load = 380 kN vi. Total extension = 60 mm vii. Diameter of the rod at the failure = 22.5 mm Determine the Young’s modulus, the stress at the elastic limit, the percentage elongation, and the percentage decrease in area.
Mechanics of rigid bodies 3. A straight bar of uniform cross section is tested in tension. The bar’s cross sectional are is 6.5 square centimeter and a length of 4m. when the tensile load reaches 85kN, the total elongation is 2.5mm What is the stress and the modulus of elasticity of the bar