2. AllmembersofthetrussAВCshown have across-sectionalarea of 500 mm² and allpins have a diameter of 20mm.Determine:2 m(a) The axial stresses in members BC andDEDFE(b) The shear stresses in the pin at A,assuming the pin is in double shear- 2 m 2 m- 2 mP = 21 kNV

given-cross sectional area of member=500mm2diameter of pin=20mm

Answered: (a) The axial stresses in members BC…

Engineering

Civil Engineering

(a) The axial stresses in members BC and DE (b) The shear stresses in the pin at A, assuming the pin is in double shear

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

1.51 In the steel structure shown, a 6-mm-diameter pin is used at C and 10-mm-diameter pins are used at B and D. The ultimate shearing stress is 150 MPa at all connections, and the ultimate normal stress is 400 MPa in link BD. Knowing that a factor of safety of 3.0 is desired, determine the largest load P that can be applied at A. Note that link BD is not reinforced around the pin holes. Front view 160 mm 13 D CB Top view 18 mm 120 mm C D Side view 6 mm
3. For the given structure and boundary conditions, what is the allowable load Pallow if the material strengths in shear and tension are T = 200 MPa and o=360 MPa, respectively? The pins carry shear and bars BC and DE carry axial load. Disregard the stress conditions of member ACD, which carries lateral load. All pins are in single-shear and have a diameter of 12mm. Use a factor of safety of 2.0. A ABC = 100mm2 B D C Pallow E ADE = 100mm² 240mm 150mm
A rigid bar BCD is connected by link at AC at point C as shown in the figure. The Structure is supported by bolts at A and B that are in the single shear. The bar is loaded by 4kn at point D. Determine the minimum diameter of the bolt at B if the allowable shear stress is 120 mpA
DProb. 2.8-8. Boom AC in Fig. P2.8-8 is supported by a rec- tangular steel bar BD, and it is attached to a bracket at C by
2. Member AB shown in the figure supports a 5 N/mm uniformly distributed load and 4kN concentrated load as shown in the figure. Determine the position x of these loads so that the average tensile stress in the tie rod AC is equal to 90% of the compressive stress at the smooth support B. The rod has a diameter of 19 mm and the contact area at is 700mm². (Hint: quadratic formula) B A X 5 N/mm 4 kN 300mm B
2. The following the truss figure, came from your Module 1. Page 9. B D F 3 m H H. E G 30 kN 70 kN 4 panels at 4 m = 16 m But this time, All the members have a cross sectional area of 850 mm². Find the normal stress of the following members а. EF b. GH c. DF
A structural member is fabricated with the cross section show below and is eccentrically loaded with F. - 26--| F 2t F b. Use G = 77.2 GPa. If I = 4 m, t= 3 mm, b = 80 mm, and F = 121 kN, Determine the maximum shear stress due to torsion. Select the correct response: 168.056 MPa 215.278 MPa 155.556 MPa of 133.333 MPa 22
The C83400-red-brass rod AB and 2014-T6- aluminum rod BC are joined at the collar B and fixed connected at their ends. If there is no load in the members when T₁ = 50°F, determine the average normal stress in each member when T₂ = 120°F. Also, how far will the collar be displaced? The cross-sectional area of each member is 1.75 in². 3 ft B 2 ft
All truss members in the truss shown are made of the same material and are of the same cross-sectional area. The failure normal tensile stress for the material is 16ksi, and the failure compressive normal stress is 10 ksi. A factor of safety, FS, of 1.6 is to be applied. The internal forces in each member can be computed using statics. As a hint, it was predetermined that the maximum forces occur at members DE and AD. Determine the following by using 4 decimal places: * Magnitude and type of axial force in member DE. * Magnitude and type of axial force in member AD. * The required area in in2 for truss member DE. * The required area in in2 for truss member AD * What is the minimum required cross-sectional area in in2 for all the members if they are to be of the same size?
the bars and truss have a cross section of 250mm^2. If thr maximum average axial stress in any bar is not to exceed 250N/mm^2, determine the magnitude of P of the loads that can be applied 2P 3m 3m -O E 2m B
Problem 01.054-Analysis of an inverted T-frame In the steel structure shown, a 6-mm-diameter pin is used at C and 12-mm-diameter pins are used at B and D. The ultimate shearin stress is 150 MPa at all connections, and the ultimate normal stress is 340 MPa in link BD. Knowing that a factor of safety of 3.0 is desired, determine the largest load P that can be applied at A. Note that link BD is not reinforced around the pin holes. Front view. 160 mm D B 18 mm B Top view 120 mm largest load P that can be applied at A is 99252 2.328 KN. ED 6 mm 22B Side view
2 من إجمالي 2 Q3 - Find the normal stress at sections A-A, B-B, C-C, and D-D for the member shown in Figure (3). A assume that the area of the member is (A mm2) , and the weight of member is (W kN) cross sectional A L/4 В В L/4 C L/2 4 4 F2 kN 3 Fi kN Figure (3)