(a) The pressure at which the steam should be reheated. (b) The thermal efficiency of the cycle. (c) Total heat input (Qin) (d) Total turbine work output (Wtur.out) (e) Draw the T-S diagram Notes: Assume the steam is reheated to the inlet temperature of the high-pressure turbine. • The moisture content of the steam at the exit of the low-pressure turbine is not to exceed 9.5% Boiler 650 C 17.5 MPa Reheater High-P turbine P₁ = Ps= Preheat 5 Pump Low-P turbine Condenser 15 KPa

(a) The pressure at which the steam should be reheated. (b) The thermal efficiency of the cycle. (c) Total heat input (Qin) (d) Total turbine work output (Wtur.out) (e) Draw the T-S diagram Notes: Assume the steam is reheated to the inlet temperature of the high-pressure turbine. • The moisture content of the steam at the exit of the low-pressure turbine is not to exceed 9.5% Boiler 650 C 17.5 MPa Reheater High-P turbine P₁ = Ps= Preheat 5 Pump Low-P turbine Condenser 15 KPa

Refrigeration and Air Conditioning Technology (MindTap Course List)

8th Edition

ISBN:9781305578296

Author:John Tomczyk, Eugene Silberstein, Bill Whitman, Bill Johnson

Publisher:John Tomczyk, Eugene Silberstein, Bill Whitman, Bill Johnson

Chapter22: Condensers

Section: Chapter Questions

Problem 8RQ: Four methods for controlling head pressure in an air-cooled condenser are ______, ______, _______,...

See similar textbooks

Similar questions

Example 2 - Super-Reheat 3 TA high-P Low-P turbine turbine Rankine Cycle high-P 3 5 turbine 4 boiler] pump 6 condenser S We are going to add a low pressure turbine (5-6) to the system we just analyzed. Before going into the L-P turbine, the exit steam from the first turbine (3-4) is reheated in the boiler at a constant pressure. Assume both 4 & 6 are at 100% saturated vapor state and the vapor exiting from the H-P turbine (state 4) expands to a lower pressure of 2 MPa (P4-2 MPa) before it is being reheated at a constant pressure to the state 5. Recalculate (a) the thermal efficiency of the system. low-P turbine -
GA: In a reaction turbine, the angles of receiving tips are 35° and of discharging tips, 20°. The blade speed is 100 m/s. Calculate the tangential force, power developed, diagram efficiency, and axial thrust of the turbine, if its steam consumption is 1 kg/min. Draw the velocity diagram on scale. B: What are the objects of using the condensers in steam plants?
A steam turbine produces 2.5 MW of work. Steam enters the turbine at 4 MPa and 400oC. Steam out turbine at 1.4 MPa and 300 C.a. What type of turbine is this (back pressure, condensing,extraction)! Why?b. Determine the steam flow rate (kg/hour)! (51963)c. Determine TSR and ASR (units must be stated)! (13,13 and20.79 kg/kWh)d. Determine the efficiency of the steam turbine!
the highest pressure of water in the power plant cycle is located a. after the boiler b. at the turbine exit c. at the exit of condenser d. at the inlet of turbine
The condensing pressure for a Rankine engine is 0.001325 MPavac. Calculate the following for steam flow rate = 1 kg/sec of steam when the steam at the beginning of expansion is at 119.6 deg SH and 4.0 Mpaa. Draw the TS and equipment diagrams for the ideal and actual case and find for the following for the ideal case: Ideal turbine work (KW). Ans.____________________________ Heat rejected at condenser (KJ/sec). Ans.____________________________ Mass of cooling water in kg/sec if cp H2O = 4.18 KJ/kg-K, and inlet temp of water to condenser = 20 deg C, outlet temp is 35 deg C. Ans.____________________________ Pump work in KW. Ans.___________________________
Q4// Answer A or B 201u, 4017 All What is the final part of the flue gas way of boiler furnace found to raise the temperature of water? Explain this?. Also, demonstrate briefly the water movement in power plant? B// What are the types of feedwater heaters in power plant, compare them? Explain the methods of cooling by these heaters and the ways of feeding.
3.) An ammonia compressor operates at evaporator pressure of 316.02 kPa and a condenser pressure of 1557 kPa. A twin-cylinder compressor with bore to stroke ratio of 0.85 is to used at 1200 rpm. The actual volumetric efficiency is 92% and compression and mechanical efficiency is 78% and 80% respectively. For a cooling capacity of 25 TR, (a) the sketch the p-h diagram labeling the evaporating and condensing temperature and pressures (b) define the all properties of ammonia taken from saturation table. Determine (c) the quantity of cooling water in the condenser in kg/min if the increase in temperature is 8°C, (d) the bore and stroke expressed in cm and (e) the size of the driving motor in hp. Given: h2 = h at 1557 kPa and s2 = s1 1695 kJ/kg
solve a,b and c asap. A steam turbine with rated capacity of 56.4 MW operates with steam at inlet conditions of 8.6 MPa and 500 oC, and discharges into a condenser at a pressure of 10kPa. Assuming a turbine efficiency of 0.75, determine: a. The state of the discharge from the turbine (saturated liquid, saturated mixture or saturated vapor...etc?) b. The steam mass flow rate c. Draw the process of steam expansion in the turbine on T-s diagram (T-s diagram only)
A simplified Rankine cycle and some data are given in the figure below. a. Show the process in a TS diagram b. Calculate the rate of heat addition (QH) to the boiler. c. Calculate Wpump- d. Calculate |Wnetl. e. Determine the thermal efficiency (n) 6 MPа, 550 °C Boiler 6 MPa w, (turbine) |mass flow rate (m): 22 kg/s Turbine Turbine efficiency (isentropic): 89 % w, (pump) 3 4 Condenser 50 КРa 50 kPa Working fluid: water
(a) What would be the necessary bore and stroke of a single acting four- cylinder, 350 rpm ammonia compressor working on simple saturation cycle between 35°C condenser and -15°C evaporator temperatures and developing 15 tons refrigeration. Given for the compressor: Ratio of stroke to bore = 1 Volumetric efficiency = 0.7 (b) If the index of compression is 1.15, find the error introduced in calculat- ing the work of compression by assuming the process to be isentropic. Also, find the heat rejected to the compressor-jacket cooling water.
3. For the gas system power illustrated in Figure 3 (with the air-standard analysis assumptions), calculate thermal efficiency, back work ratio, and Weycle -10 P₁ = 100 kPa T₁ = 350 K Oia Heat exchanger Heat exchanger Qout T₁ - 1500 K Turbine Wycle 1 T₁ - 1500 K p= 1000 kPa p= 100 kPa T₁ = 350 K Figure 3. Operating condition of a gas power system cycle (The P-V and T-S diagram)
A gas turbine cycle is preferred over steam power plant in power station that is used to generate electricity. Your manger asked you to investigate and study the possibility of upgrading the power plant discussed in Project-1 to a gas turbine cycle or a combination of both cycles (Combined cycle). The head of the department asked you to deliver a report showing a professional evaluation and assessment for gas turbine cycle efficiency given the following information.First you selected a gas-turbine power plant operating on an ideal Brayton cycle and according to the manufacturing datasheets it has the following specifications:• A pressure ratio of 10.• Heat is added to the cycle at a rate of 500 kW• Air passes through the engine at a rate of 1 kg/s• The air at the beginning of the compression is at 70 kPa and 0 C.