A- The PV array installed on the roof of a certain building has a rated power (Pmp-STC) of 600 kWp under standard test conditions. 1- Describe how to connect the SUNCECO PV modules that have 305 W, 37.24 Vmpp to construct this array if each ON-Grid inverter used to connect the PV system to the grid has a rating of P kW where P value is the last two digits (from right) of your registration number (i.e. for the student that has a registration number 202112396, P =96). The DC voltage rating at the inverter input is in the range 90 – 550 V if its rating is less than 10 kW, whereas it is in the range 450- 800 V if its rating is more than 10 kW. You have to calculate the number of series panels in each string and number of parallel strings. Draw an overall diagram for this on-grid PV system with all the protection equipment at both DC and AC side. The inverter has dual MPPTS with a rating of 10 A each. You have to include all of the analysis required to finalize your design. You may need to let number of PV modules not connected. 2- Find the real power generation of this PV array at 900 W/m² and 30 °C if the power temperature coefficient of the PV modules is -0.0045 per degree.

A- The PV array installed on the roof of a certain building has a rated power (Pmp-STC) of 600 kWp under standard test conditions. 1- Describe how to connect the SUNCECO PV modules that have 305 W, 37.24 Vmpp to construct this array if each ON-Grid inverter used to connect the PV system to the grid has a rating of P kW where P value is the last two digits (from right) of your registration number (i.e. for the student that has a registration number 202112396, P =96). The DC voltage rating at the inverter input is in the range 90 – 550 V if its rating is less than 10 kW, whereas it is in the range 450- 800 V if its rating is more than 10 kW. You have to calculate the number of series panels in each string and number of parallel strings. Draw an overall diagram for this on-grid PV system with all the protection equipment at both DC and AC side. The inverter has dual MPPTS with a rating of 10 A each. You have to include all of the analysis required to finalize your design. You may need to let number of PV modules not connected. 2- Find the real power generation of this PV array at 900 W/m² and 30 °C if the power temperature coefficient of the PV modules is -0.0045 per degree.

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

Q2 (a) Figure Q2(a) shows a single-phase full-bridge square-wave voltage source inverter has resistor (R) and inductor (L) load of 10 Q and 5 mH respectively connected in series. The inverter output frequency is 50 Hz. The transistor switching scheme is complementary bipolar. (i) Draw the output voltage and current waveforms. (ii) Obtain an expression of the rms output voltage at the fundamental frequency. (iii) If the fundamental AC output voltage is 220 V, find the required DC input voltage for the inverter. (iv) Find the instantaneos load current by considering until the 9th harmonics number. (v) Calculate the total harmonics distortion (THD) of the load current. Use only the first three odd harmonics. (vi) Sketch the harmonics spectrum for output current. (vii) Show the displacement angle a, if 5th harmonic is to be eliminated.
In a single phase VSI bridge Inverter, the load current is Io =200 sin(wt-45°)mA. The d.c. supply voltage is 220 V. What is the power drawn from the supply ?
Q2. A) What are the main differences between the three-phase bridge 180 and 120 degree modes of conduction? B) What is a single-phase current source inverter?
What is meant by FACTS in power systems? Discuss about SVC type FACTS device.
A HVDC link is operating with 175 KV AC line voltage at the rectifier. When the DC current is 1100 Amps, the rectifier delay angle is 100 and inverter extinction angle is 200. The resistance of the line is 23 ohms and the commutating reactances of the rectifier and inverter are 22 ohms and 21 ohms. Calculate the DC voltages at the rectifier and inverter terminals and the AC line voltage at the inverter.
32) Bypass diodes are MOST often located in which PV system component? O Ihverters O Modules O Combiner boxes O Charge controllers 33) Which equipment in a PV system is used to change the voltage level and waveform of electrical energy? O Inverter O Array O Controller O Transformer 34 In a PV charge controller, what does the acronym MPPT mean? O Minimum power pulse technology Maximum power point tracking O Multiple power pulse tracking O Multiple power processing technology 35) Which tilt angle for south-facing PV arrays would receive the maximum annual solar energy for latitude 38° N? O 12° O 38° 53° O 68° A JUN étv
. What are the different manufacturing/assembly steps in creating a PCB?
I need a diagram of a circuit by the transform and rectification block, using the bridge rectifier circuit (KBJ1008). It can be a source of any value. You don't need to do any calculations, just a drawing of how this circuit will look, please.
Draw a 5-stage cascaded voltage multiplier circuit for the generation of HVDC and explain the construction & working principle.
Q2. A) Draw circuit diagram and output voltage waveform of three phase inverter (120- degree condition) has Y-connected resistive load B) What are the main differences between VSI and CSI the multiple choice list for each question
iv. For six-phase half-wave rectifier circuit, the preferred circuit from the point of harmonics reduction in the supply currents is: (a) Simple six-phase half-wave circuit. (b)Double-star six-phase half-wave circuit. (c) Six-phase fork connection circuit. v. The DC supply of single phase bridge inverter is 350V. For quasi-square wave output voltage with a 70 percent ON time and frequency is 50HZ, the RMS value of output voltage is: (a) 292.8V (b) 220.5V (c) 250.6V
Explain what is meant by maximum power point and outline the importance of MPP tracking inrelation to the operation of a PV installation