A thin layer of wires forms an infinite sheet of current. There are 15 wires per meter and each wire caries a current 8 [A] as shown in the figure. Then, the magnetic flux density [µWb/m²] for x < 0 equals to: -0000 __¶¶___¶¶¶__ Im O a. -75.40âx O b.-37.70ây O c.-37.70âx O d. -188.50ây O e. -188.50âx O f. -75.40ây N wires

A thin layer of wires forms an infinite sheet of current. There are 15 wires per meter and each wire caries a current 8 [A] as shown in the figure. Then, the magnetic flux density [µWb/m²] for x < 0 equals to: -0000 ¶¶_¶¶¶__ Im O a. -75.40âx O b.-37.70ây O c.-37.70âx O d. -188.50ây O e. -188.50âx O f. -75.40ây N wires

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

show thatvthis is a magnetic flux density: then prove and interpret it with reasons on each step
An iron circuit with a small0.75 mm air gap is shown in Figure 1. A 6000 turn coil carries a current I = 18 mA which sets up a flux within the iron and across the air gap. The cross section of the iron is a consistent 0.8 cm2, and the mean length of the flux path is 0.15 m. a) Redraw the magnetic circuit using schematic symbols of an electric circuit with reluctance in each part of the circuit. b) State's Ohm's Law for magnetic circuit. c) By neglecting the effect of fringing, calculate the reluctance of the circuit. d) Find the flux within the core. N = 6000 Iron circuit (u, = 800 for iron). Figure 1
An iron circuit with a small 0.75 mm air gap is shown in Figure 1. A 6000 turn coil carries a current I = 18 mA which sets up a flux within the iron and across the air gap. The cross section of the iron is a consistent 0.8 cm2, and the mean length of the flux path is 0.15 m. a) Redraw the magnetic circuit using schematic symbols of an electric circuit with reluctance in each part of the circuit. b) State's Ohm's Law for magnetic circuit. c) By neglecting the effect of fringing, calculate the reluctance of the circuit. d) Find the flux within the core. N = 6000 Iron circuit (4, = 800 for iron).
An iron circuit with a small 0.75 mm air gap is shown in Figure 1. A 6000 turn coil carries a current I = 18 mA which sets up a flux within the iron and across the air gap. The cross section of the iron is a consistent 0.8 cm², and the mean length of the flux path is 0.15 m. a) Redraw the magnetic circuit using schematic symbols of an electric circuit with reluctance in each part of the circuit. b) State's Ohm's Law for magnetic circuit. c) By neglecting the effect of fringing, calculate the reluctance of the circuit. d) Find the flux within the core. N = 6000 Iron circuit (ur = 800 for iron).
An iron circuit with a small 0.75 mm air gap is shown in Figure 1. A 6000 turn coil carries a current I = 18 mA which sets up a flux within the iron and across the air gap. The cross section of the iron is a consistent 0.8 cm?, and the mean length of the flux path is 0.15 m. a) Redraw the magnetic circuit using schematic symbols of an electric circuit with reluctance in each part of the circuit. b) State's Ohm's Law for magnetic circuit. c) By neglecting the effect of fringing, calculate the reluctance of the circuit. d) Find the flux within the core. N = 6000 Iron circuit (4, = 800 for iron). Figure 1
4. Two current-carrying loops are arranged so that one of the loops just sits above the other just like in the figure below. The current in each loop is directed counterclockwise. Draw the resulting magnetic field for each loop to determine how the loops will "interact" with each other. 00
25 PROBLEMS 12 cm +1.5-mm gap IP1000t Armature (sheet steel) Cast steel A = 2 cm? throughout FIGURE 1.27. The relay shown in Figure 1.27 has a core made of cast steel and an armature of sheet steel. A flux of 0.8 T in the air gap produces a force that pulls in the CO armature. a. Determine the required current to pull in the armature. b. What force is exerted on the armature to overcome the spring tension? c. Assuming in the closed position the air gap is reduced to 0.1 mm, to what value may the current be reduced (dropout current of relay) just to retain closure? Assume that the same force is required in the closed position to overcome the spring force.
Consider an iron ring of 10 cmdiameter is uniformly wounded with 3000 turns of wire. The coil current is 0.25 A and a flux density of 0.6 T is set in the ring. Determine the relative permeability of the iron and magnetic field strength.
Using figures (a) and (b), a magnetic flux density of 0.1 Wb in the air gap Determine the current I in the coil with 200 turns required to produce
An iron core has a cross-sectional area of 10-3 square meter and mean circumference of 1 meter. The relative permeability of the material is 500 and the number of turns is 200. Determine the current required to set up a flux of0.001 weber. 7.54 A b. 7.96 A c. 8.19 A d. 8.47 A a.
The length of a magnetic circuit in a moving iron instrument is 300mm. The coil around the soft iron core has 360 turns and takes a current of 1.75 A. The core is square in section with sides of 20mm. Take the relative permeability of soft iron as 1100. Determine the total flux
Problem 1A core with a coil has 240 turns, to generate a flux ø of 0.008482 weber, how much should the current i1 be and what will its direction be? Relative permeabilities: metal 1 of 250 and metal 2 of 375. Core depth 25cm